Engineering topics

Mackenzie, Anne I.

Publications and source records attributed to Mackenzie, Anne I..

14 records

NASA NTRS2019

Electromagnetic Modeling for the Conformal Lightweight Antenna System for Aeronautical Communications Technologies (CLAS-ACT) Program: Final Report

A series of electromagnetic simulations was conducted for the Conformal Lightweight Antenna System for Aeronautical Communications Technologies (CLAS-ACT) Program. The program designed, built, and flight tested a 14.25 GHz conformal patch array antenna for satellite communications on a T-34C airplane. Various studies were performed to evaluate the effects of antenna element spacing, array shape, signal taper, phased array pointing angle, null steering coefficients, antenna platform, and location on the airplane. This report documents the methods and some of the results of tests done over a 2 ½ year period.

Mackenzie, Anne I.↗

NASA NTRS2018

Estimating a Large Phased Array Antenna Radiation Pattern by Computer Electromagnetic Simulation

The design of a conformal antenna for use on UAV's (Unmanned Aerial Vehicle) and other aircraft can be enhanced with computational electromagnetic modeling to determine the expected radiation patterns of the antenna when mounted on the aircraft. However, detailed simulation of the antenna structure and the aircraft together requires significant computational resources and time which may not be available. This paper details several methods for estimating the radiation pattern of a 50 by 50-element patch antenna. The Conformal Lightweight Antenna Structures for Aeronautical Communication Technologies (CLASACT) Program aims to build and test a 14.25 gigaherz (Ku-band) conformal antenna on a NASA-owned UAV. The antenna is intended for satellite communications and will enable communication between a ground station and a UAV when the separation distance is too great for line-of-sight communication. It is estimated that a 2 degree beamwidth will be necessary, requiring a 50 by 50 array of patch elements. The narrow beamwidth requirement, together with an element spacing of 0.6 lambda means that the array length will be 30 wavelengths, electrically very large. Three methods of varying complexity are described for estimating the total far-field radiation pattern. The results are shown for each method in the form of a normalized power pattern.

Mackenzie, Anne I.↗

NASA NTRS2015

EM Modeling of Far-Field Radiation Patterns for Antennas on the GMA-TT UAV

To optimize communication with the Generic Modular Aircraft T-Tail (GMA-TT) unmanned aerial vehicle (UAV), electromagnetic (EM) simulations have been performed to predict the performance of two antenna types on the aircraft. Simulated far-field radiation patterns tell the amount of power radiated by the antennas and the aircraft together, taking into account blockage by the aircraft as well as radiation by conducting and dielectric portions of the aircraft. With a knowledge of the polarization and distance of the two communicating antennas, e.g. one on the UAV and one on the ground, and the transmitted signal strength, a calculation may be performed to find the strength of the signal travelling from one antenna to the other and to check that the transmitted signal meets the receiver system requirements for the designated range. In order to do this, the antenna frequency and polarization must be known for each antenna, in addition to its design and location. The permittivity, permeability, and geometry of the UAV components must also be known. The full-wave method of moments solution produces the appropriate dBi radiation pattern in which the received signal strength is calculated relative to that of an isotropic radiator.

Mackenzie, Anne I.↗

NASA NTRS2008

New Basis Functions for the Electromagnetic Solution of Arbitrarily-shaped, Three Dimensional Conducting Bodies using Method of Moments

In this work, we present a new set of basis functions, defined over a pair of planar triangular patches, for the solution of electromagnetic scattering and radiation problems associated with arbitrarily-shaped surfaces using the method of moments solution procedure. The basis functions are constant over the function subdomain and resemble pulse functions for one and two dimensional problems. Further, another set of basis functions, point-wise orthogonal to the first set, is also defined over the same function space. The primary objective of developing these basis functions is to utilize them for the electromagnetic solution involving conducting, dielectric, and composite bodies. However, in the present work, only the conducting body solution is presented and compared with other data.

Mackenzie, Anne I.↗

NASA NTRS2008

An Alternate Set of Basis Functions for the Electromagnetic Solution of Arbitrarily-Shaped, Three-Dimensional, Closed, Conducting Bodies Using Method of Moments

In this work, we present an alternate set of basis functions, each defined over a pair of planar triangular patches, for the method of moments solution of electromagnetic scattering and radiation problems associated with arbitrarily-shaped, closed, conducting surfaces. The present basis functions are point-wise orthogonal to the pulse basis functions previously defined. The prime motivation to develop the present set of basis functions is to utilize them for the electromagnetic solution of dielectric bodies using a surface integral equation formulation which involves both electric and magnetic cur- rents. However, in the present work, only the conducting body solution is presented and compared with other data.

Mackenzie, Anne I.↗

NASA NTRS2007

New Basis Functions for the Electromagnetic Solution of Arbitrarily-shaped, Three Dimensional Conducting Bodies Using Method of Moments

In this work, we present a new set of basis functions, de ned over a pair of planar triangular patches, for the solution of electromagnetic scattering and radiation problems associated with arbitrarily-shaped surfaces using the method of moments solution procedure. The basis functions are constant over the function subdomain and resemble pulse functions for one and two dimensional problems. Further, another set of basis functions, point-wise orthogonal to the first set, is also de ned over the same function space. The primary objective of developing these basis functions is to utilize them for the electromagnetic solution involving conducting, dielectric, and composite bodies. However, in the present work, only the conducting body solution is presented and compared with other data.

Mackenzie, Anne I.↗

NASA NTRS2002

Fabrication and Electromagnetic Characterization of Novel Self-Metallized Thin Films

Unique, self-metallized films were investigated for deployable reflector antenna applications at L-band. Polyamic acid resins or soluble polyimides were doped with metal complexes, cast into films, and thermally cured. Each resulting film had a metallic layer on one side, adhering unfailingly to the polymer. Metallization was successful for silver or palladium in 3,3',4,4'-benzophenonetetracarboxylic acid dianhydride (BTDA) and 4,4'- oxydianiline and for gold in BTDA and 2,2-bis[4-(4- aminophenoxy)phenyl]hexafluoropropane (4-BDAF) or the space durable polyimide, 2,2-bis(3,4-dicarboxyphenyl)- hexafluoropropane dianhydride and 4-BDAF (LaRCCP1). Reflectivity, transmissivity, and emissivity were determined, using an HP 8510 Vector Network Analyzer, to within 0.001 precision and accuracy. A custom-made test fixture/positioner, a thru-reflect-line calibration, and calculated reflection coefficients were used. The Ag film proved most suitable for further study, with 0.9957 reflectivity and 0.0042 emissivity. The Pd films were 0.89 reflective and 0.11 emissive; both Au films tested entirely transmissive. Transmission and scanning electron micrographs, S-parameters, and power coefficients are shown.

Mackenzie, Anne I.↗

NASA NTRS2001

Comparison of Thermal Coefficients for Two Microwave Detectors

Laboratory measurements were performed to compare the thermal coefficients of two microwave detectors that might be used for direct detection in L-band radiometers. In particular it was desired to compare the performance of a new-technology flash ADC (analog-to-digital converter) against that of an older-technology diode detector in series with a VFC (voltage-to-frequency converter). The outputs of two state-of-the-art detectors were recorded as a constant 1.414-GHz signal was input and the physical temperatures of the detectors were varied over a range of 10 C. As a further experiment, each detector was tested with a noise diode source and with a sine wave synthesizer source. Thermal coefficients were computed in terms of W/C and in terms of ppt/C at nominal operating temperatures reasonable for the individual devices. Finally, thermal coefficients were calculated in K/C to indicate the change in brightness temperature seen by a theoretical sea surface salinity radiometer employing each detector. The K/C for the flash ADC was determined to be about 2.8 times that of the diode/VFC. Different reactions of the ADC to a noise input and a sine wave input indicated that ADC tests for radiometric purposes, such as this one, should be performed using a noise input.

Mackenzie, Anne I.↗

NASA NTRS2000

Three Averaging Techniques for Reduction of Antenna Temperature Variance Measured by a Dicke Mode, C-Band Radiometer

As new radiometer technologies provide the possibility of greatly improved spatial resolution, their performance must also be evaluated in terms of expected sensitivity and absolute accuracy. As aperture size increases, the sensitivity of a Dicke mode radiometer can be maintained or improved by application of any or all of three digital averaging techniques: antenna data averaging with a greater than 50% antenna duty cycle, reference data averaging, and gain averaging. An experimental, noise-injection, benchtop radiometer at C-band showed a 68.5% reduction in Delta-T after all three averaging methods had been applied simultaneously. For any one antenna integration time, the optimum 34.8% reduction in Delta-T was realized by using an 83.3% antenna/reference duty cycle.

Mackenzie, Anne I.↗

NASA NTRS1997

Measured Changes in C-Band Radar Reflectivity of Clear Air Caused by Aircraft Wake Vortices

Wake vortices from a C-130 airplane were observed at the NASA Wallops Flight Facility with a ground-based, monostatic C-band radar and an antenna-mounted boresight video camera. The airplane wake was viewed from a distance of approximately 1 km, and radar scanning was adjusted to cross a pair of marker smoke trails generated by the C-130. For each airplane pass, changes in radar reflectivity were calculated by subtracting the signal magnitudes during an initial clutter scan from the signal magnitudes during vortex-plus-clutter scans. The results showed both increases and decreases in reflectivity on and near the smoke trails in a characteristic sinusoidal pattern of heightened reflectivity in the center and lessened reflectivity at the sides. Reflectivity changes in either direction varied from -131 to -102 dBm(exp -1); the vortex-plus-clutter to noise ratio varied from 20 to 41 dB. The radar recordings lasted 2.5 min each; evidence of wake vortices was found for up to 2 min after the passage of the airplane. Ground and aircraft clutter were eliminated as possible sources of the disturbance by noting the occurrence of vortex signatures at different positions relative to the ground and the airplane. This work supports the feasibility of vortex detection by radar, and it is recommended that future radar vortex detection be done with Doppler systems.

Mackenzie, Anne I.↗

NASA NTRS1993

Windshear radar calibration, 1992 flights: Transmitter power and receiver gain stability

During the 1992 NASA airborne Doppler windshear radar flights, radar calibrations were performed prior to each flight in order to determine transmitter power, receiver gain, and receiver noise power. The calibration results show that the average transmitter power in radar mode 6 was 186 watts, with a standard deviation of 7 watts. The average high power amplifier gain was 9.62 dB. At the wide IF bandwidth setting, the receiver gain was 123.1 dB, while at the narrow IF bandwidth setting, the gain was 121.8 dB. The receiver system noise as seen at the receiver input was -107.0 dBmw using the wide IF bandwidth and -107.9 dBmw using the narrow IF bandwidth. In radar mode 7, the receiver gain was the same as in mode 6. However, the receiver noise in mode 7 was about 2.5 dB less using the wide IF bandwidth and 2.0 dB less using the narrow IF bandwidth. The R/T unit flown in 1992 had also been flown the previous year when it produced comparable results. This technical memorandum was written as a follow-up to NASA TM-107589 (June 1992), which describes similar radar calibrations performed during the 1991 windshear radar flight experiments.

Mackenzie, Anne I.↗

NASA NTRS1992

Spectrum characteristics of Denver and Philadelphia ground clutter and the problem of distinguishing wind shear targets from moving clutter

Spectral analysis of 1991 wind shear flight data has provided information about the power spectral density, spectral width, and velocity of ground clutter detected by the wind shear radar at several major airports. Ground clutter must be recognized and separated from weather targets before wind shear can be computed. Information will be presented characterizing and comparing ground clutter and weather target spectra. The information includes (1) spectral widths of stationary ground clutter seen at various scan and tilt angles, (2) power spectral density and velocity of moving ground clutter relative to the stationary ground clutter, and (3) spectral widths and velocities of weather targets. A summary of numerical results in the form of histograms and example numerical results in the form of spectral plots are presented.

Mackenzie, Anne I.↗

NASA NTRS1992

Windshear radar calibration: Transmitter power and receiver gain stability

An experimental windshear Doppler radar was flown on 27 occasions during a series of flight experiments in 1991. Radar calibrations were performed by the flight team to monitor the transmitter power and receiver gain from pre-flight to post-flight and from one day to another. From the recorded calibration data, the receiver gain and effective receiver system noise were calculated and tabulated, together with the transmitter power. These quantities of interest are compared for two receiver/transmitter (R/T) units and two intermediate frequency (IF) bandwidths that were tested in various modes. It was found that, in most operating modes, gain stayed within a 2.5-dB range and transmitter power stayed within a 20-watt range. R/T number 1 had 0.8 dB more gain and 1.2 dBm less noise power than R/T number 2. The 7-MHz IF bandwidth resulted in 1 dB more gain and 1 dBm less noise than the 2-MHz IF bandwidth. Depending on the R/T unit and IF bandwidth, the effective system noise power averaged between -107.3 dBm and -109.5 dBm.

Mackenzie, Anne I.↗

NASA NTRS1990

Radar multipath study for rain-on-radome experiments at the Aircraft Landing Dynamics Facility

An analytical study to determine the feasibility of a rain-on-radome experiment at the Aircraft Landing Dynamics Facility (ALDF) at the Langley Research Center is described. The experiment would measure the effects of heavy rain on the transmission of X-band weather radar signals, looking in particular for sources of anomalous attenuation. Feasibility is determined with regard to multipath signals arising from the major structural components of the ALDF. A computer program simulates the transmit and receive antennas, direct-path and multipath signals, and expected attenuation by rain. In the simulation, antenna height, signal polarization, and rainfall rate are variable parameters. The study shows that the rain-on-radome experiment is feasible with regard to multipath signals. The total received signal, taking into account multipath effects, could be measured by commercially available equipment. The study also shows that horizontally polarized signals would produce better experimental results than vertically polarized signals.

Mackenzie, Anne I.↗