Search NASA⌕ Search

Engineering topics

Macosko, Christopher W.

Publications and source records attributed to Macosko, Christopher W..

Polyethylene Blends for Improved Oxygen Barrier: Processing-Dependent Microstructure and Gas Permeability

Here this work demonstrates a greater than expected enhancement of oxygen barrier properties in linear low-density polyethylene (LLDPE)-based materials by blending LLDPE with high-density polyethylene (HDPE). The films made by melt pressing the LLDPE/HDPE blends had a greater reduction in oxygen permeability coefficients (PO 2 ) than predicted using common permeability reduction models, i.e., the harmonic average model and zero-permeability nanofiller model. The reduction of PO 2 was attributed to the presence of spherulite crystal structures, as revealed by atomic force microscopy combined with infrared spectroscopy (AFM-IR). The LLDPE matrix exhibited significant spherulite formation even at a relatively low addition of HDPEs, which likely formed tortuous pathways for diffusing oxygen molecules. Transport results from melt-pressed films contrast with the results from films with similar compositions prepared by film blowing, which did not show barrier enhancement beyond expectation. AFM-IR revealed that the blown films lacked spherulite crystals likely due to stretching in the machine direction followed by rapid cooling. These findings demonstrate the role of processing in controlling microstructures and thus the oxygen barrier performance. This work offers the possibility of achieving easily recyclable LLDPE-based packaging materials by simple blending of polyethylenes with different crystalline content.

36 MATERIALS SCIENCE↗

Improved Polypropylene Thermoformability through Polyethylene Layering

Due to its low cost, stiffness, and recyclability, isotactic polypropylene (iPP) is an excellent candidate for packaging applications. However, iPP is notoriously difficult to thermoform due to its low melt strength. The addition of just 10 thin layers of high-molecular-weight, linear low-density polyethylene (LLDPE) into iPP sheets by coextrusion significantly increased extensional viscosity and reduced sag. Both LLDPE and iPP were metallocene-catalyzed with excellent adhesion as measured in our previous work. Here, we performed a series of hot tensile tests and sheet sag measurements to determine the properties of the iPP sheet and the multilayer sheet between 130 and 180 °C. To evaluate the thermoformability of these multilayer sheets, truncated conical cups were positive vacuum formed at different temperatures and heating times, and the crush strength was measured. Cups that released easily from the mold with good shape retention and a crush strength within 80% of the maximum value were used to define a temperature–time thermoformability window. We estimated the maximum stress that occurred during the thermoforming process to be 5 MPa. Layer thicknesses before and after thermoforming were used to estimate an average strain of 0.78. The thin LLDPE layers decreased the yield stress below 5 MPa. This enabled thermoforming at sheet temperatures as low as 150 °C. The immiscible LLDPE interfaces increased extensional viscosity, which decreased sag in the multilayer sheets compared to iPP. This broadened the thermoforming range to temperatures as high as 180 °C and allowed longer heating times. These highly thermoformable, layered sheets may be recycled as iPP since they contain only 8% of LLDPE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of a Layered Morphology on Drip Suppression in Burning Polymers

Fire safety in polymers is critically important with products such as textiles and consumer goods, as well as materials used in construction, aerospace, transportation, and furniture. Additives used as anti-dripping and flame-retardant agents impose acute human health issues and have negative environmental impacts. With a focus on developing additive-free solutions, here we used multilayer coextrusion to fabricate layered polyethylene/polypropylene (PE/PP) films and investigated the effect of a layered morphology on dripping and burning rates. The experimental results for multilayered PE/PP samples were compared to control groups of melt blended PE/PP samples. The multilayer configuration provides two significant advantages: 154% delay in the time to the first drip and up to 87% reduction in the number of drips compared to the value for the melt blended samples with no additives. PE/PP blends with up to 2 wt % polytetrafluoroethylene, a commonly used anti-dripping agent in the industry, showed only 85% delay in the time to the first drip and about 60% reduction in the number of drips. We discovered a linear relationship between film thickness and burning rate, which allows for the use of the volumetric burning rate to normalize the effect of film thickness. No benefit in the burning rate was observed when comparing multilayered structures and conventional melt blended architectures or blends with PTFE. Annealing studies and transmission electron microscopy at areas close to the combustion zones confirmed that higher extensional viscosities induced by the layered structures and morphological changes due to the layer breakup play an important role in reducing dripping. By combining the first drip time and overall drip numbers, a parameter, “dripping index”, was defined to establish a fire safety map to simplify material comparisons. This study demonstrates that a multilayer film geometry can provide an additive-free solution to yield control over fire safety parameters in polymers.

36 MATERIALS SCIENCE↗

Sub-Micrometer Zeolite Films on Gold-Coated Silicon Wafers with Single-Crystal-Like Dielectric Constant and Elastic Modulus

A low-temperature synthesis coupled with mild activation produces zeolite films exhibiting low dielectric constant (low-k) matching the theoretically predicted and experimentally measured values for single crystals. This synthesis and activation method allows for the fabrication of a device consisting of a b-oriented film of the pure-silica zeolite MFI (silicalite-1) supported on a gold-coated silicon wafer. The zeolite seeds are assembled by a manual assembly process and subjected to optimized secondary growth conditions that do not cause corrosion of the gold underlayer, while strongly promoting in-plane growth. The traditional calcination process is replaced with a non-thermal photochemical activation to ensure preservation of an intact gold layer. The dielectric constant (k), obtained through measurement of electrical capacitance in a metal-insulator-metal configuration, highlights the ultralow k approximate to 1.7 of the synthetized films, which is among the lowest values reported for an MFI film. There is large improvement in elastic modulus of the film (E approximate to 54 GPa) over previous reports, potentially allowing for integration into silicon wafer processing technology.

Tiriolo, Raffaele↗

Open‐Pore Two‐Dimensional MFI Zeolite Nanosheets for the Fabrication of Hydrocarbon‐Isomer‐Selective Membranes on Porous Polymer Supports

Abstract Two‐dimensional zeolite nanosheets that do not contain any organic structure‐directing agents were prepared from a multilamellar MFI (ML‐MFI) zeolite. ML‐MFI was first exfoliated by melt compounding and then detemplated by treatment with a mixture of H 2 SO 4 and H 2 O 2 (piranha solution). The obtained OSDA‐free MFI nanosheets disperse well in water and can be used for coating applications. Deposits made on porous polybenzimidazole (PBI) supports by simple filtration of these suspensions exhibit an n ‐butane/isobutane selectivity of 5.4, with an n ‐butane permeance of 3.5×10 −7 mol m −2 s −1 Pa −1 (ca. 1000 GPU).

Zhang, Han↗

Open‐Pore Two‐Dimensional MFI Zeolite Nanosheets for the Fabrication of Hydrocarbon‐Isomer‐Selective Membranes on Porous Polymer Supports

Abstract Two‐dimensional zeolite nanosheets that do not contain any organic structure‐directing agents were prepared from a multilamellar MFI (ML‐MFI) zeolite. ML‐MFI was first exfoliated by melt compounding and then detemplated by treatment with a mixture of H 2 SO 4 and H 2 O 2 (piranha solution). The obtained OSDA‐free MFI nanosheets disperse well in water and can be used for coating applications. Deposits made on porous polybenzimidazole (PBI) supports by simple filtration of these suspensions exhibit an n ‐butane/isobutane selectivity of 5.4, with an n ‐butane permeance of 3.5×10 −7 mol m −2 s −1 Pa −1 (ca. 1000 GPU).

Zhang, Han↗

Accelerating Reactive Compatibilization of PE/PLA Blends by an Interfacially Localized Catalyst

Here, we show catalyst localized at the interface can compatibilize polyethylene (PE) and polylactide (PLA) blends. Telechelic hydroxyl functional PE was synthesized by ring opening metathesis polymerization, which reacted with PLA in melt mixing (shown by adhesion and droplet size reduction). We also examined lewis acid tin catalysts as interfacial reaction promoters, with the goal of interfacial localization. Finally, stannous octoate was shown to localize at the interface by transmission electron microscopy with energy dispersive X-ray spectroscopy and improved dispersion of PLA in PE as compared to uncatalyzed materials and a nonlocalized tin chloride dihydrate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗