Search NASA⌕ Search

Engineering topics

Maddox, B.

Publications and source records attributed to Maddox, B..

The structure of sc16 GaP obtained at 17.5 GPa and 1400 K

We report using a laser-heated diamond anvil cell, a powdered sample of gallium phosphide was compressed to 17.5 GPa and heated up to 1400 K. The material obtained was characterized at room temperature using synchrotron x-ray diffraction. Experimental results were compared with first-principles calculations. The polymorph observed assumes the simple cubic structure (sc16) initially reported for GaAs at high pressures. Microdiffraction mapping showed variable grain sizes of the synthesized phase, with the largest grains located in the middle of the heated spot. Structural refinements were performed on selected grains. The structure predicted based on first-principles calculations is in close agreement with the experiments. The two Ga–P bonds show similar lengths in sc16-GaP; however, the bond angles differ, resulting in a distorted tetrahedral coordination geometry.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Inferring Strength of Tantalum from Hydrodynamic Instability Recovery Experiments

Hydrodynamic instability experiments allow access to material properties at extreme conditions, where strain rates exceed 105 s -1 and pressures reach 100 GPa. Current hydrodynamic instability experimental methods require in-flight radiography to image the instability growth at high pressure and high strain rate, limiting the facilities where these experiments can be performed. An alternate approach, recovering the sample after loading, allows measurement of the instability growth with profilometry. Tantalum samples were manufactured with different 2D and 3D initial perturbation patterns and dynamically compressed by a blast wave generated by laser ablation. The samples were recovered from peak pressures between 30 and 120 GPa and strain rates on the order of 107 s -1 , providing a record of the growth of the perturbations due to hydrodynamic instability. These records are useful validation points for hydrocode simulations using models of material strength at high strain rate. Recovered tantalum samples were analyzed, providing an estimate of the strength of the material at high pressure and strain rate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dynamic Behavior of Engineered Lattice Materials

Additive manufacturing (AM) is enabling the fabrication of materials with engineered lattice structures at the micron scale. These mesoscopic structures fall between the length scale associated with the organization of atoms and the scale at which macroscopic structures are constructed. Dynamic compression experiments were performed to study the emergence of behavior owing to the lattice periodicity in AM materials on length scales that approach a single unit cell. For the lattice structures, both bend and stretch dominated, elastic deflection of the structure was observed ahead of the compaction of the lattice, while no elastic deformation was observed to precede the compaction in a stochastic, random structure. The material showed lattice characteristics in the elastic response of the material, while the compaction was consistent with a model for compression of porous media. Here, the experimental observations made on arrays of 4 x 4 x 6 lattice unit cells show excellent agreement with elastic wave velocity calculations for an infinite periodic lattice, as determined by Bloch wave analysis, and finite element simulations.

36 MATERIALS SCIENCE↗

K{sub α} and bremsstrahlung x-ray radiation backlighter sources from short pulse laser driven silver targets as a function of laser pre-pulse energy

Measurements of silver K-shell and bremsstrahlung emission from thin-foil laser targets as a function of laser prepulse energy are presented. The silver targets were chosen as a potential 22 keV backlighter source for the National Ignition Facility Experiments. The targets were irradiated by the Titan laser with an intensity of 8 × 10{sup 17} W/cm{sup 2} with 40 ps pulse length. A secondary nanosecond timescale laser pulse with controlled, variable energy was used to emulate the laser prepulse. Results show a decrease in both K{sub α} and bremsstrahlung yield with increasing artificial prepulse. Radiation hydrodynamic modeling of the prepulse interaction determined that the preplasma and intact target fraction were different in the three prepulse energies investigated. Interaction of the short pulse laser with the resulting preplasma and target was then modeled using a particle-in-cell code PSC which explained the experimental results. The relevance of this work to future Advanced Radiographic Capability laser x-ray backlighter sources is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laser shocking of materials: Toward the national ignition facility

In recent years a powerful experimental tool has been added to the arsenal at the disposal of the materials scientist investigating materials response at extreme regimes of strain rates, temperatures, and pressures: laser compression. In this paper, this technique has been applied successfully to mono-, poly-, and nanocrystalline metals and the results have been compared with predictions from analytical models and molecular dynamics simulations. Special flash x-ray radiography and flash x-ray diffraction, combined with laser shock propagation, are yielding the strength of metals at strain rates on the order of 10 7 –10 8 s -1 and resolving details of the kinetics of phase transitions. A puzzling result is that experiments, analysis, and simulations predict dislocation densities that are off by orders of magnitude. Finally, other surprises undoubtedly await us as we explore even higher pressure/strain rate/temperature regimes enabled by the National Ignition Facility.

36 MATERIALS SCIENCE↗