Search NASA⌕ Search

Engineering topics

Maggiora, R

Publications and source records attributed to Maggiora, R.

Density profile sensitivity study of ASDEX Upgrade ICRF Antennas with the TOPICA code

During operation of the ASDEX Upgrade (AUG) ion cyclotron radio frequency (ICRF) system, Tungsten (W)-coated poloidal limiters and structures connected along magnetic field lines to the antenna can be sources of W, which is attributed to sputtering by ions accelerated in radio frequency (RF) sheaths. In order to analyze and optimize the ICRF antenna performance, accurate and efficient simulation tools are necessary. TOPICA code was developed for analysis of ICRF antenna systems with plasma loading conditions modeled with ID FELICE code. This paper presents an initial comparative analysis of two AUG ICRF antennas for a set of model plasma density profiles (with varying density gradient and antenna cut-off distance). The antennas are presently installed in AUG and differ in that one was partially optimized using HFSS code to reduce E{sub ||} near fields. Power transferred to plasma and sheath driving RF potentials are computed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recent Results on Coupling Fast Waves to High Performance Plasmas on DIII-D

Fast Waves (FWs) at 60 MHz and 90 MHz are used in DIII-D for central electron heating and current drive. Coupling of FWs to high-performance discharges is limited by low antenna loading in these regimes. To extend the application of high-power FWs to such regimes, methods of increasing the antenna loading in these regimes are needed. A systematic study of loading enhancement techniques has been carried out in DIII-D, including reduction of the antenna/plasma distance, gas puffing into the far scrape-off layer (SOL), and control of other parameters that affect the particle balance in the far SOL. Quantitative understanding of the physics of the loading resistance and its dependence on edge density profiles is demonstrated. The core FW heating efficiency appeared to be {approx}100% in the Advanced Inductive regime, consistent with the high first-pass direct electron absorption of {approx}75% that is predicted by the ray-tracing code GENRAY in this high electron beta regime.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

JET ITER-Like Antenna Analysis Using the TOPICA Code

In this work, we carried out the analysis of the recently installed JET ITER-Like antenna with TOPICA code. Comparisons between TOPICA simulations and measurements taken during the actual experiment are instead part of the overview talk on the JET ITER-Like antenna [4]. As routinely done for all simulated antennas, TOPICA inputs are the technical drawings of the launcher and the accurate density and temperature profiles, which, in this case, have been provided by the JET team. The standard outputs are the input parameters of the antenna, namely the impedance matrix, the electric current distribution and the electric field pattern at the interface between the antenna region and the plasma column. This work, together with [4], provides an additional proof that the code can be adopted to predict the behavior of the JET ITER-Like antenna, and to confidently pass to the next step, i.e. using TOPICA for the challenging task of optimizing the complex design of the actual ITER antenna. More generally viewed, the possibility to reliably simulate the detailed geometry of an ICRF antenna, given a realistic plasma description, and to obtain the actual antenna input parameters, is of paramount importance to evaluate and predict the system performances, and to assist in system operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

UWB radar technique for arc detection in coaxial cables and waveguides

As spread spectrum technology has revolutionized the communications industry, Ultra Wide Band (UWB) technology is dramatically improving radar performances. These advanced signal processing techniques have been adapted to coaxial cables and waveguides to provide new features and enhanced performance on arc detection. UWB signals constituted by a sequence of chips (properly chosen to reduce side lobes and to improve detection accuracy) are transmitted along the transmission lines at a specified Pulse Repetition Frequency (PRF) and their echoes are received by means of directional couplers. The core of the receiver is an ultra high-speed correlator implemented in a Digital Signal Processor (DSP). When a target (arc) is detected, its position and its 'radar cross section' are calculated to be able to provide the arc position along the transmission line and to be able to classify the type of detected arc. The 'background scattering' is routinely extracted from the received signal at any pulse. This permits to be resilient to the background structure of transmission lines (bends, junctions, windows, etc.). Thanks to the localization feature, segmentation is also possible for creating sensed and non-sensed zones (for example, to be insensitive to antenna load variations)

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Performance of the ITER ICRF Antenna plug as expected from TOPICA matrices

The performances of the present ICRF antenna plug design is evaluated by means of the TOPICA 24x24 matrix for plasma loading supplemented by 4-port junction (4PJ) matrices. For their interpretation these results are compared with a cruder modeling by the semi-analytical code ANTITER II. From this analysis we conclude: (1) The broadbanding effect of the service stub on the response of the 4PJ made for one triplet is maintained for the complete array for all the heating and current drive phasings. (2) For a given maximum voltage of the 8 feeding lines the radiated power capability is roughly constant in the entire frequency band. (3) The power capability of the array is significantly dependent on the distance of the antenna to the Last Closed Flux Surface, the density profile in the scrape-off layer (SOL) and on the toroidal and poloidal phasings. The dependence on phasing is stronger for wider SOL (4) For a not too optimistic plasma density profile (Sc2 shortl7) a power capability exceeding 20 MW is only obtained for the 00 {pi}{pi} heating toroidal phasing and for the co-current drive phasing in the upper part of the frequency band for a maximum voltage in the complete system of 45 kV. (5), On account of the plasma gyrotropy the quadrature poloidal phasing introduced by hybrid feeding must excite waves propagating upwards in the ITER configuration to obtain the best coupling, (6) The large power capability difference between opposite current drive phasings is attributed to the coupling between the toroidal and poloidal phasings induced by the poloidal steady magnetic field.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Electromagnetic Modelling of Dielectric Loads in front of an ICRH ITER Array using TOPICA and HFSS codes for comparison

The antenna scattering (S-matrix) or impedance matrix at location where the antenna is connected to the power system is of crucial importance to assess compliance with power handling requirements and to design the tuning-and-matching system. The electrical behaviour of an Ion Cyclotron Resonance Heating (ICRH) ITER antenna in front of an infinite isotropic load was assessed numerically using the HFSSR and TOPICA codes for comparison. The calculations were performed at 45 MHz, for various thicknesses of the vacuum layer, various relative permittivities {epsilon}' for dielectric medium without losses ({epsilon}'' = 0),{epsilon}' ranging from 81 to 1000 and for various conductive losses {epsilon}'' = {sigma}/{epsilon}{sub 0}{center_dot}{omega}, for electrolyte medium ({epsilon}' = 81),{epsilon}'' ranging from 0 to 1000. The numerical results obtained with TOPICA and HFSS codes show a good overall agreement in case of vacuum, dielectric and electrolyte mediums. The best absorption of the fast magneto-sonic (Alfven) waves into the loads (i.e. the minimum of the module of antenna input reflection coefficient S11) is obtained around {epsilon}' = 400 for dielectric medium and around {epsilon}'' = 400 for electrolyte case.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On the Use of EBG in ICRF and LH Launcher

High impedance surfaces or electromagnetic band gap (EBG) surfaces have proved themselves to be useful in wireless communications applications due to their unique characteristics such as no propagating surface wave support, no conduction of RF current for a given bandwidth, in-phase electromagnetic reflection and non-inverted image of the electric charge in front of them. These characteristics make possible to design compact antennas achieving better performance in terms of radiation and input impedance. ICRF and LH antennas in plasma experiments can take advantage of using EBG surfaces. One of the main issues in ICRF plasma heating is the low power coupling of the plasma facing antenna. The adoption of EBG surfaces in the ICRF antenna structure and the advantages offered by a predictive designing tool as TOPICA offer the possibility to improve significantly the coupled power to plasma. The adoption of EBG surfaces in the LH waveguides permits to reduce the major dimension of waveguides not affecting drastically the propagation. It is then possible to manufacture more compact LH arrays of waveguides.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Analysis of LH Launcher Arrays (Like the ITER One) Using the TOPLHA Code

TOPLHA (Torino Polytechnic Lower Hybrid Antenna) code is an innovative tool for the 3D/1D simulation of Lower Hybrid (LH) antennas, i.e. accounting for realistic 3D waveguides geometry and for accurate 1D plasma models, and without restrictions on waveguide shape, including curvature. This tool provides a detailed performances prediction of any LH launcher, by computing the antenna scattering parameters, the current distribution, electric field maps and power spectra for any user-specified waveguide excitation. In addition, a fully parallelized and multi-cavity version of TOPLHA permits the analysis of large and complex waveguide arrays in a reasonable simulation time. A detailed analysis of the performances of the proposed ITER LH antenna geometry has been carried out, underlining the strong dependence of the antenna input parameters with respect to plasma conditions. A preliminary optimization of the antenna dimensions has also been accomplished. Electric current distribution on conductors, electric field distribution at the interface with plasma, and power spectra have been calculated as well. The analysis shows the strong capabilities of the TOPLHA code as a predictive tool and its usefulness to LH launcher arrays detailed design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗