Search NASA⌕ Search

Engineering topics

Mahurin, Shannon Mark

Publications and source records attributed to Mahurin, Shannon Mark.

31 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Bifunctional Ionic Covalent Organic Networks for Enhanced Simultaneous Removal of Chromium(VI) and Arsenic(V) Oxoanions via Synergetic Ion Exchange and Redox Process

Chromium (VI) and arsenic (V) oxoanions are major toxic heavy metal pollutants in water threatening both human health and environmental safety. Here, the development is reported of a bifunctional ionic covalent organic network (iCON) with integrated guanidinium and phenol units to simultaneously sequester chromate and arsenate in water via a synergistic ion-exchange-redox process. The guanidinium groups facilitate the ion-exchange-based adsorption of chromate and arsenate at neutral pH with fast kinetics and high uptake capacity, whereas the integrated phenol motifs mediate the Cr(VI)/Cr(III) redox process that immobilizes chromate and promotes the adsorption of arsenate via the formation of Cr(III)-As(V) cluster/complex. The synergistic ion-exchange-redox approach not only pushes high adsorption efficiency for both chromate and arsenate but also upholds a balanced Cr/As uptake ratio regardless of the change in concentration and the presence of interfering oxoanions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Synthesis of Poly(ionic Liquid)s-block-poly(methyl Methacrylate) Copolymer-Grafted Silica Particle Brushes with Enhanced CO 2 Permeability and Mechanical Performance

Poly(ionic liquid) (PIL)-based block copolymers are of particular interest as they combine the specific properties of PILs with the self-assembling behaviors of block copolymers, broadening the range of potential applications for PIL-based materials. In this work, three particle brushes: SiO 2 -g-poly(methyl methacrylate) (PMMA), SiO 2 -g-PIL, and SiO 2 -g-PMMA-b-PIL were prepared through surface-initiated atom transfer radical polymerization. Unlike the homogeneous homopolymer particle brushes, the block copolymer particle brush SiO 2 -g-PMMA-b-PIL exhibited a bimodal chain architecture and unique phase-separated morphology, which were confirmed by size-exclusion chromatography and transmission electron microscopy. In addition, the influence of the introduction of the PMMA segment on the gas separation and mechanical performance of the PIL-containing block copolymer particle brushes were investigated. A significant improvement of Young’s modulus was observed in the SiO 2 -g-PMMA-b-PIL compared to the SiO 2 -g-PIL bulk films; meanwhile, their gas separation performances (CO 2 permeability and CO 2 /N 2 selectivity) were the same, which demonstrates the possibility of improving the mechanical properties of PIL-based particle brushes without compromising their gas separation performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

CO 2 Chemisorption Behavior of Coordination-Derived Phenolate Sorbents

CO 2 chemisorption via C-O bond formation is an efficient methodology in carbon capture especially using phenolate-based ionic liquids (ILs) as the sorbents to afford carbonate products. However, most of the current IL systems involve alkylphosphonium cations, leading to side reactions via the ylide intermediate pathway. It is important to figure out the CO 2 chemisorption behavior of phenolate-derived sorbents using inactive and easily accessible cation counterparts without active protons. Herein, phenolate-based systems were constructed via coordination between alkali metal cations with crown ethers to avoid the participation of active protons in CO 2 chemisorption. Reaction pathway study revealed that CO 2 uptake could be achieved by O-C bond formation to afford carbonate. CO 2 uptake capacity and reaction enthalpy were significantly influenced by the coordination effect, alkali metal types, and alkyl groups on the benzene ring.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Synthesis and Characterization of Macrocyclic Ionic Liquids for CO 2 Separation

In this work, a series of ionic liquids with symmetric, macrocyclic cations composed of N-heterocycles connected by alkyl or ether linkages coupled with bis(trifluoromethylsulfonyl)imide or bis(pentafluoroethanesulfonyl)amide anions were synthesized to explore their application in CO 2 separation. These novel ionic liquids showed selective physical absorption of CO 2 compared to N 2 making them potential candidates for carbon capture. We examined the effect of cation structure on the physicochemical and separations properties of the ionic liquid and showed that these ionic liquids exhibit an inverse relationship between molar volume and CO 2 sorption capacity following the trend predicted by models based on regular solution theory. The fractional free volumes of the ionic liquids were lower than typical alkyl-imidazolium ionic liquids despite the cyclic structure of the cations which could be related to the flexibility of the alkyl and ether linkages. These results provide added insight into our understanding of structure–property relationships in CO 2 solubility in ionic liquids and afford a path toward enhancing the separations properties based on structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Molecular dynamics simulations of a dicationic ionic liquid for CO 2 capture

A dicationic ionic liquid ([DBU-PEG][Tf 2 N] 2 ) was studied using classical molecular dynamics simulations to examine its structural and gas separation properties. The dication was designed in an attempt to improve CO 2 solubility by means of tuning the cation-anion interactions of the ionic liquid (IL). The computational model was compared to experimentally obtained density, viscosity, and powder X-ray diffraction spectra. The structure of the IL was further investigated with radial distribution functions and free volume analysis through cavity distributions. It was found that the shape and charge distribution of the dication enhances CO 2 interaction: the CO 2 molecule is hugged by the dication along the PEG linker and close to one of the cationic ends. Here, the geminal design of the dication allows for strong interaction with CO 2 , showing promise as a means of carbon capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Broadening the Gas Separation Utility of Monolayer Nanoporous Graphene Membranes by an Ionic Liquid Gating

Ultrathin two-dimensional (2D) monolayer atomic crystal materials offer great potential for extending the field of novel separation technology due to their infinitesimal thickness and mechanical strength. One difficult and ongoing challenge is to perforate the 2D monolayer material with subnanometer pores with atomic precision for sieving similarly sized molecules. Here, we demonstrate the exceptional separation performance of ionic liquid (IL)/graphene hybrid membranes for challenging separation of CO 2 and N 2 . Notably, the ultrathin ILs afford dynamic tuning of the size and chemical affinity of nanopores while preserving the high permeance of the monolayer nanoporous graphene membranes. The hybrid membrane yields a high CO 2 permeance of 4000 GPU and an outstanding CO 2 /N 2 selectivity up to 32. Finally, this rational hybrid design provides a universal direction for broadening gas separation capability of atomically thin nanoporous membranes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Understanding Materials Characteristics of Palladium Lanthanide Cermet Wires as a Mimic of Californium Wire Production

Californium-252 (Cf-252) has been synthesized on a large scale (mg) since the 1970s for use as a portable neutron source. With a half-life of 2.645 years and a spontaneous fission fraction of 3.09%, Cf-252 emits 2.31 × 10 12 neutrons/gram second. Today most of the Cf-252 produced in the world is made at Oak Ridge National Laboratory (ORNL) using the High Flux Isotope Reactor (HFIR) and the Radiochemical Engineering Development Center (REDC). Because of its highly radioactive nature, all manipulations of Cf-252 need to be performed in hot cell facilities by highly trained personnel. The Cf-252 produced at ORNL is done at the REDC, which is conveniently located next to the HFIR. Cf-252 is sold as bulk wire, which has been described as palladium (Pd) metal incasing californium oxide (Cf 2 O 3 ). The process was developed by Mosley et al. at Savannah River Laboratory (SRL) where it was modeled after the thorium work done by Fuschillo et al. This process has been used since the 1970s to synthesize this unique wire, but its fundamental chemistry and materials characteristics were never openly reported. Here we aim to better understand the chemistry and the materials characteristics of Cf-252 wire production for process improvements and to better our fundamental understanding of the mid-late actinides. Though there are many challenges in working with radioactive elements such as Cf, the isotope Cf-252 is even more complicated due to its neutron emission. One challenge with neutron emission is the ability of neutrons to penetrate much deeper through materials, causing radiation damage. This makes using instrumentation to characterize the chemistry and materials properties of this process difficult. For this reason, this study will first focus on terbium (Tb) as a surrogate for Cf. Currently Tb is used as a carrier or filler in Cf production when small amounts of Cf are being processed. This, along with their similar size and charge, makes Tb a reasonable surrogate for this study.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ambient Temperature Graphitization Based on Mechanochemical Synthesis

Graphite has become a critical material because of its high supply risk and essential applications in energy industries. Its present synthesis still relies on an energy-intensive thermal treatment pathway (Acheson process) at about 3000 °C. Herein, a mechanochemical approach is demonstrated to afford highly crystalline graphite nanosheets at ambient temperature. The key to the success of our methodology lies in the successive decomposition and rearrangement of a carbon nitride framework driven by a denitriding reaction in the presence of magnesium. The afforded graphite features high crystallinity, a high degree of graphitization, a thin nanosheet architecture, and a small flake size, which endow it with superior efficiency in lithium-ion batteries as an anode material in terms of rate capacity and cycle stability. Finally, the mild and cost-effective pathway used in this study could be a promising alternative for graphite production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Porous thermally insulating compositions containing hollow spherical nanoparticles

A method of thermally insulating a surface, the method comprising applying a coating of a thermally insulating composition onto said surface, wherein said thermally insulating composition comprises: (i) hollow spherical nanoparticles having a mean particle size of less than 800 nm in diameter and a particle size distribution in which at least 90% of the hollow spherical nanoparticles have a size within ±20% of said mean particle size, and a first layer of cationic or anionic molecules attached to said surfaces of the hollow spherical nanoparticles; and (ii) a second layer of molecules of opposite charge to the first layer of molecules, wherein said second layer of molecules of opposite charge are ionically associated with said first layer of molecules, wherein the molecules in said second layer have at least eight carbon atoms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Revealing 3D Morphological and Chemical Evolution Mechanisms of Metals in Molten Salt by Multimodal Microscopy

Growing interest in molten salts as effective high-temperature heat-transfer fluids for sustainable energy systems drives a critical need to fundamentally understand the interactions between metals and molten salts. This work utilizes the multimodal microscopy methods of synchrotron X-ray nanotomography and electron microscopy to investigate the 3D morphological and chemical evolution of two-model systems, pure nickel metal and Ni-20Cr binary alloy, in a representative molten salt (KCl-MgCl2 50–50 mol %, 800 °C). In both systems, unexpected shell-like structures formed because of the presence of more noble tungsten, suggesting a potential route of using Ni–W alloys for enhanced molten-salt corrosion resistance. The binary alloy Ni-20Cr developed a bicontinuous porous structure, reassembling functional porous metals manufactured by dealloying. This work elucidates better mechanistic understanding of corrosion in molten salts, which can contribute to the design of more reliable alloys for molten salt applications including next-generation nuclear and solar power plants and opens the possibility of using molten salts to fabricate functional porous materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ion-gated carbon molecular sieve gas separation membranes

Membrane technology lies at the heart of many industrial gas separation processes and applications. Molecular sieving membranes that break the Robeson limit are desirable for energy-efficient gas separation. In this paper, we report a facile strategy of directly integrating ionic liquids (ILs) into porous membranes. Particularly, the ILs form an ultra-thin layer on the carbon molecular sieve (CMS) membranes rather than penetrating into the pores, acting as a smart gate for gas entry to boost the selectivity. The hybrid membrane exhibits CO 2 permeability >600 barrer and enhanced CO 2 /N 2 selectivity >50, which surpasses the Robeson limit and shows potential in CO 2 /N 2 separation process. Molecular dynamics simulations confirm the gating effect of the IL layer of molecular thickness. In conclusion, this work demonstrates a universal strategy to improve CMS membrane performance by creating an IL-membrane interface and tuning the ion-pore interaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗