Search NASA⌕ Search

Engineering topics

Maitra, Shraddha

Publications and source records attributed to Maitra, Shraddha.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Transgenic Sugarcane–Oilcane: An Alternative Feedstock for the Production of Drop-in Fuel and Value-Added Bioproducts

The utilization of plants and other agricultural produce can partly offset petroleum dependency for energy requirements and can potentially provide sustainable solutions to global environmental problems. To this end, synthetic biology has shown great potential in developing transgenic bioenergy grasses such as sugarcane, sorghum, miscanthus, and energy cane that hyperaccumulate energy-rich lipid molecules in their vegetative tissues, such as leaves, stems, and roots. These perennial high-biomass transgenic C4 grasses are not targeted to grow on prime agricultural land and can be dedicatedly used to produce biofuels and other value-added bioproducts. Recently, sugarcane has been metabolically engineered to sequestrate carbon from juice towards biosynthesis of lipid molecules in the vegetative tissues. Transgenic sugarcane is referred to as “oilcane.” Transgenic sugarcane–oilcane has improved energy density due to an elevated lipid content in the vegetative tissues. Transgenic bioenergy crops cater to both cellulosic sugars and vegetative lipids, hence resulting in higher biofuel yield (biodiesel/renewable diesel and bioethanol) per unit area of cultivable land. In this book chapter, the genetic engineering of sugarcane and its bioprocessing are discussed to illustrate its development and use as an alternative feedstock for the production of biofuels (bio-jet fuel, biodiesel, and bioethanol) and value-added bioproducts.

Maitra, Shraddha↗
DOE OSTI2024

Economic and environmental sustainability of bio-based HMF production and recovery from lignocellulosic biomass

5-Hydroxymethyl furfurals (HMF) is one of the versatile platform chemicals. However, green routes to produce it directly from lignocellulosic biomass are lacking. A significant amount of HMF produced during the hydrothermal valorization of lignocellulosic biomass is considered undesired and ends up in a waste stream. The study transformed the undesired byproduct into a valuable coproduct by advancing the existing biofuel production process. A detailed economic and environmental sustainability analysis of the integrated biorefinery design was performed. The evaluation showed that the biorefinery could afford a maximum feedstock purchasing price of $\$115.17$ per MT and produce HMF with a minimum selling price of $\$4.54$ per kg which is ~75% lower than the commercial price of HMF. The median global warming potential of HMF was estimated to be 3.92 kg CO 2 -eq. per kg HMF which was ~32% less than its counterpart bio-based p-xylene. Diverse coproducts produced in the biorefinery using transgenic feedstock positively impacted sustainability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Data for Sustainable Co-Production of Plant Lipids and Cellulosic Sugars from Transgenic Energycane at an Industrially Relevant Scale: A Proof of Concept for Alternative Feedstocks

Development of sustainable and scalable technologies to convert lignocellulosic biomass to biofuels is critical to achieving carbon neutrality. The potential of transgenic bioenergy crops as a renewable source of sugars and lipids has been demonstrated at bench-scale. However, scaling up these processes is important for holistic analysis. Here proof-of-concept for chemical-free hydrothermal pretreatment of transgenic energycane-oilcane line L13 at an industrially relevant scale to recover vegetative lipids along with cellulosic sugars is presented. Pilot-scale processing of 97 kg of transgenic energycane-oilcane L13 stems and high solids pretreatment of bagasse enhanced the recovery of cellulosic glucose and xylose by 5-fold as compared to untreated bagasse and helped in the enrichment of vegetative lipids in the biomass residues which allowed its recovery at the end of the bioprocess. Palmitic and oleic acids were the predominant fatty acids (FAs) extracted from stems and leaves. The processing did not affect lipid composition. The efficiency of lipid recovery from untreated biomass was 75.9% which improved to 88.7% upon pretreatment. The vegetative tissues of transgenic energycane-oilcane L13 contained 0.42 metric tons/hectare of lipids. Processing vegetative tissues yielded 0.38 metric tons/hectare of lipids. This approaches an oil yield similar to soybean (global average 0.44 metric tons/hectare) and is almost twice as high as the oil yield from sugarcane engineered to hyperaccumulate lipids (0.20 metric tons/hectare). The study suggests that further optimization by state-of-the-art metabolic engineering and biomass processing can establish transgenic bioenergy crops for commercial drop-in fuel production.

Biomass Analytics↗
DOE OSTI2024

Sustainable co-production of plant lipids and cellulosic sugars from transgenic energycane at an industrially relevant scale: A proof of concept for alternative feedstocks

Development of sustainable and scalable technologies to convert lignocellulosic biomass to biofuels is critical to achieving carbon neutrality. The potential of transgenic bioenergy crops as a renewable source of sugars and lipids has been demonstrated at bench-scale. However, scaling up these processes is important for holistic analysis. Here proof-of-concept for chemical-free hydrothermal pretreatment of transgenic energycane-oilcane line L13 at an industrially relevant scale to recover vegetative lipids along with cellulosic sugars is presented. Here, pilot-scale processing of 97 kg of transgenic energycane-oilcane L13 stems and high solids pretreatment of bagasse enhanced the recovery of cellulosic glucose and xylose by 5-fold as compared to untreated bagasse and helped in the enrichment of vegetative lipids in the biomass residues which allowed its recovery at the end of the bioprocess. Palmitic and oleic acids were the predominant fatty acids (FAs) extracted from stems and leaves. The processing did not affect lipid composition. The efficiency of lipid recovery from untreated biomass was 75.9% which improved to 88.7% upon pretreatment. The vegetative tissues of transgenic energycane-oilcane L13 contained 0.42 metric tons/hectare of lipids. Processing vegetative tissues yielded 0.38 metric tons/hectare of lipids. This approaches an oil yield similar to soybean (global average 0.44 metric tons/hectare) and is almost twice as high as the oil yield from sugarcane engineered to hyperaccumulate lipids (0.20 metric tons/hectare). The study suggests that further optimization by state-of-the-art metabolic engineering and biomass processing can establish transgenic bioenergy crops for commercial drop-in fuel production.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Application of Time-Domain 1 H NMR for Investigating Dynamics of Vegetative Lipids in Bioenergy Crops at Different Developmental Stages

Sweet sorghum is typically cultivated for the food and fodder market. Recently, sweet sorghum varieties are being metabolically transitioned to enhance energy density by accumulating oil droplets in their vegetative tissues for bioenergy applications. Owing to the high biomass yield of sorghum, the transgenic lines can compete with oil-seed crops for biodiesel yield per unit area. In the initial phase of transgenic development, a high-throughput phenotyping method can bridge the gap between the production pipeline and analysis to improve the efficiency of the process. To meet the requirement, the present study extends the application of time-domain 1 H-NMR spectroscopy for rapid quantification and characterization of the total in-situ lipids of sweet sorghum ‘ramada’ to lay the groundwork for analyzing the upcoming large quantity of transgenic samples. NMR technology has been successfully established for analyzing lipid contents of vegetative tissues of non-transgenic variety. The multiexponential analysis of spin-lattice (T 1 ) relaxation spectra obtained from TD-NMR aided the investigation of the dynamics of the free and bound lipid fraction with plant development. The total lipid concentration of bagasse and leaves of non-transgenic sweet sorghum remained unchanged throughout the plant development. Leaves displayed a higher percentage of bound lipids as compared to bagasse. Here, a significant variation in the lipid concentration of juice was observed at the different growth stages with a maximum lipid accumulation of 1.21 ± 0.04% w/w at the boot stage that decreased with further maturity of the plant.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Data for Application of Time-Domain 1H NMR for Investigating Dynamics of Vegetative Lipids in Bioenergy Crops at Different Developmental Stages

Sweet sorghum is typically cultivated for the food and fodder market. Recently, sweet sorghum varieties are being metabolically transitioned to enhance energy density by accumulating oil droplets in their vegetative tissues for bioenergy applications. Owing to the high biomass yield of sorghum, the transgenic lines can compete with oil-seed crops for biodiesel yield per unit area. In the initial phase of transgenic development, a high-throughput phenotyping method can bridge the gap between the production pipeline and analysis to improve the efficiency of the process. To meet the requirement, the present study extends the application of time-domain 1H-NMR spectroscopy for rapid quantification and characterization of the total in-situ lipids of sweet sorghum ‘ramada’ to lay the groundwork for analyzing the upcoming large quantity of transgenic samples. NMR technology has been successfully established for analyzing lipid contents of vegetative tissues of non-transgenic variety. The multiexponential analysis of spin-lattice (T1) relaxation spectra obtained from TD-NMR aided the investigation of the dynamics of the free and bound lipid fraction with plant development. The total lipid concentration of bagasse and leaves of non-transgenic sweet sorghum remained unchanged throughout the plant development. Leaves displayed a higher percentage of bound lipids as compared to bagasse. A significant variation in the lipid concentration of juice was observed at the different growth stages with a maximum lipid accumulation of 1.21 ± 0.04% w/w at the boot stage that decreased with further maturity of the plant.

Biomass Analytics↗
DOE OSTI2023

Chemical-free production of multiple high-value bioproducts from metabolically engineered transgenic sugarcane ‘oilcane’ bagasse and their recovery using nanofiltration

Bioenergy crops have potential for being a sustainable and renewable feedstock for biofuels and various value- added bioproducts. The study utilizes recently developed transgenic sugarcane (‘oilcane’) bagasse for chemical- free coproduction of high-value bioproducts, i.e., furfurals, HMF, acetic acid, cellulosic sugars, and vegetative lipids. Hydrothermal pretreatment was optimized at 210°C for 5 min to coproduce 6.91%, 2.67%, 5.07%, 2.42% and 37.82% (w/w) furfurals, HMF, acetic acid, vegetative lipids, and cellulosic sugars, respectively from lignocellulosic biomass. Additionally, nanofiltration system in-series was successfully established to recover sugars, furfurals, HMF, and acetic acid from the pretreatment liquor. 1st nanofiltration with Duracid NF mem- brane rejected ~99% sugars. Concentrated sugars with significantly reduced inhibitory products were obtained in retentate for fermentation. 2nd nanofiltration with NF90 membrane used permeate of 1st nanofiltration as feed and rejected ~ 86% furfurals. Furthermore, the work demonstrates the feasibility of coproducing and recovering multiple biochemicals from lignocellulosic biomass.

09 BIOMASS FUELS↗
DOE OSTI2023

Data for Chemical-Free Production of Multiple High-Value Bioproducts from Metabolically Engineered Transgenic Sugarcane ‘Oilcane’ Bagasse and Their Recovery Using Nanofiltration

Bioenergy crops have potential for being a sustainable and renewable feedstock for biofuels and various value-added bioproducts. The study utilizes recently developed transgenic sugarcane (“oilcane”) bagasse for chemical-free coproduction of high-value bioproducts, i.e., furfurals, HMF, acetic acid, cellulosic sugars, and vegetative lipids. Hydrothermal pretreatment was optimized at 210 °C for 5 min to coproduce 6.91%, 2.67%, 5.07%, 2.42% and 37.82% (w/w) furfurals, HMF, acetic acid, vegetative lipids, and cellulosic sugars, respectively from lignocellulosic biomass. Additionally, nanofiltration system in-series was successfully established to recover sugars, furfurals, HMF, and acetic acid from the pretreatment liquor. 1st nanofiltration with Duracid NF membrane rejected ∼99% sugars. Concentrated sugars with significantly reduced inhibitory products were obtained in retentate for fermentation. 2nd nanofiltration with NF90 membrane used permeate of 1st nanofiltration as feed and rejected ∼ 86% furfurals. The work demonstrates the feasibility of coproducing and recovering multiple biochemicals from lignocellulosic biomass.

Biomass Analytics↗
DOE OSTI2022

Bioprocessing, Recovery, and Mass Balance of Vegetative Lipids from Metabolically Engineered “Oilcane” Demonstrates Its Potential as an Alternative Feedstock for Drop-In Fuel Production

Plant oils are increasingly in demand as renewable feedstocks for biodiesel and biochemicals. Currently, oilseeds are the primary source of plant oils. Although the vegetative tissues of plants express lipid metabolism pathways, they do not hyper- accumulate lipids. Elevated synthesis, storage, and accumulation of lipids in vegetative tissues have been achieved by metabolic engineering of sugarcane to produce “oilcane”. This study evaluates the potential of oilcane as a renewable feedstock for the co- production of lipids and fermentable sugars. Oilcane was grown under favorable climatic and field conditions in Florida (FLOC) as well as during an abbreviated growing season, outside its typical growing region, in Illinois (ILOC). The potential lipid yield of 0.35 tons/ha was projected from the hyperaccumulation of fatty acids in the stored vegetative biomass of FLOC, which is approaching the lipid yield of soybean (0.44 tons/ha). Processing of the vegetative tissues of oilcane recovered 0.20 tons/ha, which represents the recovery of 55% of the total lipids from FLOC. Chemical-free hydrothermal bioprocessing of ILOC and FLOC bagasse and leaves at 180 °C for 10 min prevented the degeneration of in situ plant lipids. Here, this allowed the recovery of lipids at the end of the bioprocess with a major fraction of lipids remaining in the biomass residues after pretreatment and saccharification. Improvements through refined biomass processing, crop management, and metabolic engineering are expected to boost lipid yields and make oilcane a prime feedstock for the production of biodiesel.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Data for Bioprocessing, Recovery, and Mass Balance of Vegetative Lipids from Metabolically Engineered ‘Oilcane’ Demonstrates Its Potential as an Alternative Feedstock for Drop-In Fuel Production

Plant oils are increasingly in demand as renewable feedstocks for biodiesel and biochemicals. Currently, oilseeds are the primary source of plant oils. Although the vegetative tissues of plants express lipid metabolism pathways, they do not hyper-accumulate lipids. Elevated synthesis, storage, and accumulation of lipids in vegetative tissues have been achieved by metabolic engineering of sugarcane to produce “oilcane.” This study evaluates the potential of oilcane as a renewable feedstock for the co-production of lipids and fermentable sugars. Oilcane was grown under favorable climatic and field conditions in Florida (FLOC) as well as during an abbreviated growing season, outside its typical growing region, in Illinois (ILOC). The potential lipid yield of 0.35 tons/ha was projected from the hyperaccumulation of fatty acids in the stored vegetative biomass of FLOC, which is approaching the lipid yield of soybean (0.44 tons/ha). Processing of the vegetative tissues of oilcane recovered 0.20 tons/ha, which represents the recovery of 55% of the total lipids from FLOC. Chemical-free hydrothermal bioprocessing of ILOC and FLOC bagasse and leaves at 180 °C for 10 min prevented the degeneration of in situ plant lipids. This allowed the recovery of lipids at the end of the bioprocess with a major fraction of lipids remaining in the biomass residues after pretreatment and saccharification. Improvements through refined biomass processing, crop management, and metabolic engineering are expected to boost lipid yields and make oilcane a prime feedstock for the production of biodiesel.

Conversion↗
DOE OSTI2022

The effects of sequential hydrothermal-mechanical refining pretreatment on cellulose structure changes and sugar recoveries

The recalcitrance of lignocellulosic biomass necessitates an efficient pretreatment protocol for operating a successful cellulosic biorefinery. It is critical to improve cellulose accessibility for hydrolysis and fermentation by altering the plant cell wall’s physical structure and chemical composition. Sequential hydrothermal-mechanical refining pretreatment (HMR) allows efficient recovery of cellulosic sugars without utilizing any hazardous chemicals. HMR has been successfully applied to Liberty switchgrass, a bioenergy cultivar released by the USDA, and now it is being applied to oilcane, a recently developed transgenic sugarcane variety engineered to accumulate lipids in its vegetative tissues. Sugar yields of oilcane bagasse (OCB) and switchgrass (SG) treated with HMR are 96.4% and 75.4%, respectively. This study sought to correlate cellulosic sugar yields with structural changes within the cell wall caused by HMR on two distinct bioenergy crops. Simon’s staining technique for the specific surface area analysis showed that HMR increased the specific surface area of pretreated biomass residues by 80–112%. In addition, ATR-FTIR was performed to determine the effects of HMR on physical structures based on the total crystallinity index (TCI) and hydrogen bonding intensity (HBI). Irrespective of biomass type, HMR decreased the initial crystalline cellulose contents of untreated biomass residues by 3.5% and reduced TCI and HBI by 7–13%. Here, the study found that sugar yields were negatively correlated to reducing values of hydrogen bonding intensity, crystalline cellulose content, and total crystallinity index.

09 BIOMASS FUELS↗
DOE OSTI2022

Data for The Effects of Sequential Hydrothermal-Mechanical Refining Pretreatment on Cellulose Structure Changes and Sugar Recoveries

The recalcitrance of lignocellulosic biomass necessitates an efficient pretreatment protocol for operating a successful cellulosic biorefinery. It is critical to improve cellulose accessibility for hydrolysis and fermentation by altering the plant cell wall’s physical structure and chemical composition. Sequential hydrothermal-mechanical refining pretreatment (HMR) allows efficient recovery of cellulosic sugars without utilizing any hazardous chemicals. HMR has been successfully applied to Liberty switchgrass, a bioenergy cultivar released by the USDA, and now it is being applied to oilcane, a recently developed transgenic sugarcane variety engineered to accumulate lipids in its vegetative tissues. Sugar yields of oilcane bagasse (OCB) and switchgrass (SG) treated with HMR are 96.4% and 75.4%, respectively. This study sought to correlate cellulosic sugar yields with structural changes within the cell wall caused by HMR on two distinct bioenergy crops. Simon’s staining technique for the specific surface area analysis showed that HMR increased the specific surface area of pretreated biomass residues by 80-112%. In addition, ATR-FTIR was performed to determine the effects of HMR on physical structures based on the total crystallinity index (TCI) and hydrogen bonding intensity (HBI). Irrespective of biomass type, HMR decreased the initial crystalline cellulose contents of untreated biomass residues by 3.5% and reduced TCI and HBI by 7-13%. The study found that sugar yields were negatively correlated to reducing values of hydrogen bonding intensity, crystalline cellulose content, and total crystallinity index.

Biomass Analytics↗
DOE OSTI2022

A consolidated bioprocess design to produce multiple high-value platform chemicals from lignocellulosic biomass and its technoeconomic feasibility

5-Hydroxymethyl furfural (HMF) and furfurals are DOE-listed platform chemicals that can be derived from the renewable carbon in the lignocellulosic biomasses and have the potential to replace petroleum-derived alter- natives. High substrate cost and use of expensive solvents limit the economic feasibility of bio-based HMF production on an industrially relevant scale. The study presents an experimental optimized condition that maximizes the chemical-free production of HMF and furfurals without lowering the yield of total fermentable sugars from Saccharum bagasse. Hydrothermal pretreatment at 210 °C for 15 min yielded approximately 10%, 12%, and 46% of HMF, furfurals, and fermentable sugars per gram of dry biomass, respectively. Additionally, the study proposes a consolidated bioprocess model to produce and recover four high-value bioproducts i.e., HMF, furfurals, ethanol, and acetic acid based on the experimental results and evaluates its technoeconomic feasibility considering HMF as the main product. The minimum selling price (MSP) of HMF was estimated to be 930.6 USD/ t which is competitive with its petroleum-derived precursor alternative p-xylene (1,113 USD/t). The sensitivity analysis performed for the process parameters suggests that pretreatment cost and revenues from coproducts immensely influence the MSP of HMF. The preliminary technoeconomic analysis performed on the consolidated bioprocess design indicates that additional revenue streams from diversified coproducts in biorefineries aid in lowering the MSP of high-value bioproducts.

09 BIOMASS FUELS↗
DOE OSTI2022

Data for A Consolidated Bioprocess Design to Produce Multiple High-Value Platform Chemicals from Lignocellulosic Biomass and Its Technoeconomic Feasibility

5-hydroxymethyl furfural (HMF) and furfurals are DOE-listed platform chemicals that can be derived from the renewable carbon in the lignocellulosic biomasses and have the potential to replace petroleum-derived alternatives. High substrate cost and use of expensive solvents limit the economic feasibility of bio-based HMF production on an industrially relevant scale. The study presents an experimental optimized condition that maximizes the chemical-free production of HMF and furfurals without lowering the yield of total fermentable sugars from Saccharum bagasse. Hydrothermal pretreatment at 210 °C for 15 min yielded approximately 10%, 12%, and 46% of HMF, furfurals, and fermentable sugars per gram of dry biomass, respectively. Additionally, the study proposes a consolidated bioprocess model to produce and recover four high-value bioproducts i.e., HMF, furfurals, ethanol, and acetic acid based on the experimental results and evaluates its technoeconomic feasibility considering HMF as the main product. The minimum selling price (MSP) of HMF was estimated to be 930.6 USD/t which is competitive with its petroleum-derived precursor alternative p-xylene (1,113 USD/t). The sensitivity analysis performed for the process parameters suggests that pretreatment cost and revenues from coproducts immensely influence the MSP of HMF. The preliminary technoeconomic analysis performed on the consolidated bioprocess design indicates that additional revenue streams from diversified coproducts in biorefineries aid in lowering the MSP of high-value bioproducts.

Conversion↗
DOE OSTI2022

Data for Optimizing Chemical-Free Pretreatment for Maximizing Oil/Lipid Recovery from Transgenic Bioenergy Crops and its Rapid Analysis Using Time Domain-NMR

Transgenic bioenergy crops have shown the potential to produce vegetative oil by accumulating energy-rich triacylglyceride molecules that can be converted into biofuels (biodiesel and biojet). These transgenic crops cater to improved biofuel yield by providing lipids along with cellulosic sugars. Efficient bioprocessing technologies are needed to utilize these transgenic plants to their maximum potential. To this end, this study investigates a low- and high-severity chemical-free hydrothermal pretreatment of transgenic oilcane 1566 bagasse with in situ lipids to maximize the recovery of lipids for biodiesel and fermentable sugars for ethanol with minimal inhibitor generation. Hydrothermal pretreatment at 170°C recovered ∼25% of total lipids in the pretreatment liquor, leaving the remainder in bagasse residue for hexane recovery post fermentation. The recovery of lipids in pretreatment liquor remained constant beyond 170°C. Along with lipids, ∼35% w/w and ∼50% w/w fermentable sugars were recovered post saccharification from bagasse pretreated at 170°C and 210°C for 20 min, respectively. Hydrothermal pretreatment at 170°C for 20 min provided the optimum conditions for maximum recovery of lipids and cellulosic sugars that resulted in enhanced biofuel yield per unit biomass. High severity pretreatment increased the generation of inhibitors beyond the tolerance of fermentation microorganisms. In addition, the application of time-domain proton NMR spectroscopy was extended to bioprocessing. NMR technology facilitated the analysis of total lipids, the composition of fatty acids, and the characterization of free and bound lipids in untreated and pretreated oilcane 1566 bagasse subsequent to each step of biomass to biofuel conversion.

Conversion↗
DOE OSTI2021

Development and validation of time‐domain 1 H‐NMR relaxometry correlation for high‐throughput phenotyping method for lipid contents of lignocellulosic feedstocks

Abstract The bioenergy crops such as energycane, miscanthus, and sorghum are being genetically modified using state of the art synthetic biotechnology techniques to accumulate energy‐rich molecules such as triacylglycerides (TAGs) in their vegetative cells to enhance their utility for biofuel production. During the initial genetic developmental phase, many hundreds of transgenic phenotypes are produced. The efficiency of the production pipeline requires early and minimally destructive determination of oil content in individuals. Current screening methods require time‐intensive sample preparation and extraction with chemical solvents for each plant tissue. A rapid screen will also be needed for developing industrial extraction as these crops become available. In the present study, we have devised a proton relaxation nuclear magnetic resonance ( 1 H‐NMR) method for single‐step, non‐invasive, and chemical‐free characterization of in‐situ lipids in untreated and pretreated lignocellulosic biomass. The systematic evaluation of NMR relaxation time distribution provided insight into the proton environment associated with the lipids in the biomass. It resolved two distinct lipid‐associated subpopulations of proton nuclei that characterize total in‐situ lipids into bound and free oil based on their “molecular tumbling” rate. The T1T2 correlation spectra also facilitated the resolution of the influence of various pretreatment procedures on the chemical composition of molecular and local 1 H population in each sample. Furthermore, we show that hydrothermally pretreated biomass is suitable for direct NMR analysis unlike dilute acid and alkaline pretreated biomass which needs an additional step for neutralization.

pretreatment↗
DOE OSTI2020

Balancing sugar recovery and inhibitor generation during energycane processing: Coupling cryogenic grinding with hydrothermal pretreatment at low temperatures

Pretreatment of lignocellulosic biomass at high temperatures or with oxidizing chemicals generate various inhibitors that restrict the efficient bioconversion of sugars in subsequent steps. The present study systematically investigates individual and combinatorial effects of pretreatment parameters on the generation of inhibitors. Herein, a plot between pretreatment temperature and inhibitor revealed optimum pretreatment temperature for energycane bagasse i.e., 170 °C beyond which total inhibitor production increased exponentially. No inhibitor production was observed on mechanical processing i.e., disk milling/cryogenic grinding of biomass. Evaluation of response surface regression exhibited that biomass solids loading has a significant effect on inhibitor generation at higher temperatures. The concentrations of certain inhibitors such as acetic acid, furfurals, and HMF increased more than 3-folds on doubling the solids loading. Furthermore, a novel low-severity approach of low-temperature hydrothermal pretreatment coupled with cryogenic grinding for lignocellulosic biomasses has been introduced which improved sugar yields while maintaining a low inhibitor concentration.

09 BIOMASS FUELS↗