Engineering topics

Majumdar, B. C.

Publications and source records attributed to Majumdar, B. C..

6 records

NASA NTRS1988

Stability of a rigid rotor supported on flexible oil journal bearings

This investigation deals with the stability characteristics of oil journal bearings, including the effect of elastic distortions in the bearing liner. Graphical results are presented for (1) steady-state load, (2) stiffness and damping coefficients, and (3) the stability. These results are given for various slenderness ratios, eccentricity ratios, and elasticity parameters. The lubricant is first assumed to be isoviscous. The analysis is then extended to the case of a pressure-dependent viscosity. It has been found that stability decreases with increase of the elasticity parameter of the bearing liner for heavily loaded bearings.

Majumdar, B. C.↗

NASA NTRS1987

Stability of a rigid rotor supported on oil-film journal bearings under dynamic load

Most published work relating to dynamically loaded journal bearings are directed to determining the minimum film thickness from the predicted journal trajectories. These do not give any information about the subsynchronous whirl stability of journal bearing systems since they do not consider the equations of motion. It is, however, necessary to know whether the bearing system operation is stable or not under such an operating condition. The stability characteristics of the system are analyzed. A linearized perturbation theory about the equilibrium point can predict the threshold of stability; however it does not indicate postwhirl orbit detail. The linearized method may indicate that a bearing is unstable for a given operating condition whereas the nonlinear analysis may indicate that it forms a stable limit cycle. For this reason, a nonlinear transient analysis of a rigid rotor supported on oil journal bearings under: (1) a unidirectional constant load, (2) a unidirectional periodic load, and (3) variable rotating load are performed. The hydrodynamic forces are calculated after solving the time-dependent Reynolds equation by a finite difference method with a successive overrelaxation scheme. Using these forces, equations of motion are solved by the fourth-order Runge-Kutta method to predict the transient behavior of the rotor. With the aid of a high-speed digital computer and graphics, the journal trajectories are obtained for several different operating conditions.

Majumdar, B. C.↗

NASA NTRS1982

Frictional heating due to asperity interaction of elastohydrodynamic line-contact surfaces

A numerical solution of an elastohydrodynamically lubricated (EHL) line contact between two long, rough-surface cylinders that considers the frictional heating of asperities was obtained. Pressure distribution, temperature distribution, film thickness and EHL load for given speeds, lubricant properties, material properties of surfaces, and surface roughness parameters were theoretically solved by simultaneous solution of the elasticity equation and the Reynolds equation for two partially lubricated rough surfaces. The pressure due to asperity contact was calculated by assuming a Gaussian distribution of surface irregularities. The elastic deformation used for film thickness computation was found from the two kinds of pressure by plane strain analysis. The temperature rise in the contact zone was calculated by using the Blok-Jaeger flash temperature model. The effects of surface roughness on EHL load for various slide-role ratios, surface roughness parameters, surface patterns, and temperature parameters was studied. It was found that the maximum temperature rise in most cases occurred in the inlet zone, and that the minimum film thickness decreased and the maximum temperature increased as the surface roughness was increased.

Majumdar, B. C.↗

NASA NTRS1981

Effect of surface roughness on elastohydrodynamic line contact

A numerical solution of an elastohydrodynamic lubrication (EHL) contact between two long rough surface cylinders is obtained. A simultaneous solution of an elasticity equation and the Reynolds equation for two partially lubricated rough surfaces is used to obtain a theoretical solution of pressure distribution, elastohydrodynamic load and film thicknesses for given speeds. A theoretical solution is also found for lubricants with pressure dependent viscosity, material properties of cylinders, and surface roughness parameters. Elastic deformation is found from hydrodynamic and contact pressure using plane strain analysis, and results indicate that for a constant central film thickness, increasing the surface roughness decreases the EHL load and there is little variation in minimum film thicknesses as the surface roughness is increased.

Majumdar, B. C.↗

NASA NTRS1981

Effect of Surface Roughness on Hydrodynamic Bearings

A theoretical analysis on the performance of hydrodynamic oil bearings is made considering surface roughness effect. The hydrodynamic as well as asperity contact load is found. The contact pressure was calculated with the assumption that the surface height distribution was Gaussian. The average Reynolds equation of partially lubricated surface was used to calculate hydrodynamic load. An analytical expression for average gap was found and was introduced to modify the average Reynolds equation. The resulting boundary value problem was then solved numerically by finite difference methods using the method of successive over relaxation. The pressure distribution and hydrodynamic load capacity of plane slider and journal bearings were calculated for various design data. The effects of attitude and roughness of surface on the bearing performance were shown. The results are compared with similar available solution of rough surface bearings. It is shown that: (1) the contribution of contact load is not significant; and (2) the hydrodynamic and contact load increase with surface roughness.

Majumdar, B. C.↗

NASA NTRS1981

Surface roughness effect on finite oil journal bearings

A theoretical study of the performance of finite oil journal bearings is made, considering the surface roughness effect. The total load supporting ability under such a condition derives from the hydrodynamic as well as asperity contact pressure. These two components of load are calculated separately. The average Reynolds equation for partially lubricated surfaces is used to evaluate hydrodynamic pressure. An analytical expression for average film thickness is obtained and introduced to modify the average Reynolds equation. The resulting differential equation is then solved numerically by finite difference methods for mean hydrodynamic pressure, which in turn gives the hydrodynamic load. Assuming the surface height distribution as Gaussian, the asperity contact pressure is found. The effect of surface roughness parameter, surface pattern, eccentricity ratio, and length to diameter ratio on hydrodynamic load and on side leakage is investigated. It is shown that hydrodynamic load increases with increasing surface roughness when both journal and bearing surfaces have identical roughness structures or when the journal only has a rough surface. The trend of hydrodynamic load is reversed if the journal surface is smooth and the bearing surface is rough.

Majumdar, B. C.↗