Search NASA⌕ Search

Engineering topics

Malik Thompson

Publications and source records attributed to Malik Thompson.

Radiation-Conditioned Ti–hBN Coatings for Space Mechanisms: Bridging Tribology and Irradiation Effects from Laboratory to Low-Earth Orbit

The longevity of tribological components in extraterrestrial environments is challenged by abrasive regolith, extreme temperatures, and ionizing radiation. This study evaluates the performance of vacuum plasma sprayed (VPS) Ti-2vol.% hexagonal boron nitride (hBN) coatings applied to joint mechanisms such as rod and slot, ball and socket, and hinge assemblies, fabricated from Al6061 and Ti6Al4V for planetary structures. Coated and uncoated samples were tested under vacuum with lunar regolith simulant (JSC-1A), followed by environmental exposures including electron radiation and thermal cycling. Results show that coated samples consistently outperformed uncoated counterparts across all configurations. Wear depth in coated components was reduced by over 80%, as confirmed by 3D profilometry and surface imaging. SEM analysis revealed severe abrasion and localized plastic deformation in uncoated surfaces, while coated samples retained structural integrity due to synergy of hard protective phases formed during deposition and retained hBN providing solid lubrication in the sliding surface. Coated and exposed samples exhibited smoother actuation profiles and reduced friction, indicating a beneficial "conditioning" effect from environmental exposure. The coatings-maintained performance even on complex geometries with minimal delamination. These findings demonstrate the potential of VPS Ti-hBN coatings to extend the operational life of lunar mechanisms, bridging laboratory-scale tribology with flight-relevant mechanical applications.

tribology↗

Wear and Neutron Shielding Resilience of Titanium-Hexagonal Boron Nitride Coatings Against Extreme Lunar Radiation and Thermal Cycles

Ti6Al4V and Al6061 are aerospace alloys used in lunar structural components and rovers owing to their high specific strength. However, they deteriorate rapidly when subjected to demanding conditions of the lunar environment, such as extreme thermal cycles, solar particle radiation, and abrasive regolith. Cryo-milled powders were employed to deposit hBN-reinforced protective titanium coatings through plasma spray (atmospheric APS and vacuum-VPS) with 2 and 10 vol% of hBN on Ti6Al4V and Al6061 substrates. These coatings were evaluated for durability under extreme lunar-like conditions, including thermal cycling, electron radiation, and synergistic (electron radiation-thermal cycle) exposure. The coatings exhibited radiation-induced hardening, resulting in a substantial increase in their microhardness ~20–40% compared to virgin condition. Bright-field transmission electron microscopy (TEM) analysis reveals the presence of high dislocation densities, black dot defects, and dislocation clusters, providing evidence of the severe impact of synergistic environmental stresses. Ball-on-disk tribological tests were conducted in the presence of JSC-1 A lunar regolith simulant to evaluate the wear performance of coatings. Compared to conventional Ti6Al4V substrate, 50%, 90%, and 70% reductions in wear volume were observed in the Ti/2 vol% hBN coatings in thermal-only, radiation-only, and synergistic environments. Neutron shielding tests indicate that the synergistic coatings offer higher neutron shielding performance by up to 28% compared to virgin coatings, attributed to improved neutron capture by 10B isotopes. Upon a comprehensive assessment and ranking of multiple coatings under varying conditions, the VPS Ti/2 vol% hBN coating emerges as the top choice for protection against extreme radiation and thermal cycles for future lunar explorations.

Boron nitride↗

Tribological and Radiation Shielding Response of Novel Titanium-Boron Nitride Coatings for Lunar Structural Components

Aluminum (Al) and titanium (Ti) lightweight alloys play a crucial role in space systems due to their exceptional strength-to-weight ratio. However, their premature failure in the presence of lunar regolith and their lack of neutron shielding ability are significant challenges. To address these issues, we have developed air and vacuum plasma-sprayed hBN (hexagonal Boron Nitride) -reinforced titanium coatings with 2 and 10 vol% of hBN. Tribological studies conducted with JSC-1 A lunar regolith simulant revealed a 90 % reduction in wear volume for the Ti/2 vol% hBN coatings compared to conventional materials due to the synergistic action of harder secondary phases and solid lubrication effect of hBN. Additionally, a 27 % enhancement in radiation shielding is obtained based on the mass absorption coefficient (radiation absorbed per sample density and thickness) for VPS Ti/2 vol% hBN coatings.

Wear↗

Metallic Environmentally Resistant Coatings Rapid Innovation Initiative (MERCRII) Mechanism Development and Testing

This project seeks to address the high friction and low wea resistance of lightweight aluminum (Al) and titanium (Ti) alloys to extend the lifetime and sustainability of both lunar and Martian assets missions by developing advanced wear-and radiation-resistant. MERCRII started with 6 candidate coating materials and 3 candidate application methods that were down-selected through pathfinder and 2 phases of testing to one coating configuration: Ti64 with 2%hBN Vacuum Plasma Spray.

dust mitigation↗

Speckle Pattern for Woven Softgood Habitats Photogrammetry Testing

Space habitation is becoming more accessible and commercially available which is driving the development and testing of inflatable softgoods habitats that can be both lighter and more volume-efficient than heritage metallic pressure vessels. Photogrammetry test methods are used on new materials and larger inflatable softgood test articles to measure material displacement and strain during pressurization. A speckle pattern must be applied to the surface of interest for testing when using photogrammetry which is typically a very labor and time intensive process. Two methods were tested as options for a faster and more effective application to hand painting and temporary tattoos, which are the current application methods for the structural/restraint layer. One approach was to mix a plastic additive with a matte clear coat to create a speckle pattern that could be applied to the article. The second method uses a speckle paint gun to speckle the article after a white base coat is applied. Both methods adhered well to the Kevlar test sample materials and showed up well when examined with photogrammetry cameras. On the woven test samples the additive in a clear coat method could be applied evenly as was the paint gun method.

Rylee Cardon↗

Speckle Pattern Application to Woven Softgoods

Space habitation is becoming more accessible and commercially available which is driving the development and testing of inflatable softgoods habitats that can be both lighter and more volume-efficient than heritage metallic pressure vessels. Photogrammetry test methods are used on new materials and larger inflatable softgood test articles to measure material displacement and strain during pressurization. A speckle pattern must be applied to the surface of interest for testing when using photogrammetry which is typically a very labor and time intensive process. Two methods were tested as options for a faster and more effective application to hand painting and temporary tattoos, which are the current application methods for the structural/restraint layer. One approach was to mix a plastic additive with a matte clear coat to create a speckle pattern that could be applied to the article. The second method uses a speckle paint gun to speckle the article after a white base coat is applied. Both methods adhered well to the Kevlar test sample materials and showed up well when examined with photogrammetry cameras. On the woven test samples the additive in a clear coat method could be applied evenly as was the paint gun method.

Rylee Cardon↗

Speckle Pattern Application to Woven Softgoods

Space habitation is becoming more accessible and commercially available which is driving the development and testing of inflatable softgoods habitats that can be both lighter and more volume-efficient than heritage metallic pressure vessels. Photogrammetry test methods are used on new materials and larger inflatable softgood test articles to measure material displacement and strain during pressurization. A speckle pattern must be applied to the surface of interest for testing when using photogrammetry which is typically a very labor and time intensive process. Two methods were tested as options for a faster and more effective application to hand painting and temporary tattoos, which are the current application methods for the structural/restraint layer. One approach was to mix a plastic additive with a matte clear coat to create a speckle pattern that could be applied to the article. The second method uses a speckle paint gun to speckle the article after a white base coat is applied. Both methods adhered well to the Kevlar test sample materials and showed up well when examined with photogrammetry cameras. On the woven test samples the additive in a clear coat method could be applied evenly as was the paint gun method.

Rylee Cardon↗