Revolutionary Computational Aerosciences (RCA) Research Portfolio and CFD 2030
No abstract available
Malik, Mujeeb R.↗
Engineering topics
Malik, Mujeeb R.
Publications and source records attributed to Malik, Mujeeb R..
Large-Eddy Simulation of Axisymmetric Compression Corner Flow
The Wall-Modeled Large Eddy Simulation (WMLES) approach is used to study the interaction of a shock wave with a high Reynolds number turbulent boundary layer. Since the near wall region is modeled, high Reynolds number turbulent flows can be simulated at a moderate computational cost. The case considered is that of an axisymmetric Mach 2.85 turbulent boundary layer over a 30 compression corner. The Reynolds number of the boundary layer upstream of the interaction based on momentum thickness (Re theta = u sub infinity theta/v sub infinity) is ~12,000. The geometry and flow conditions match the experiments of Dunagan et al. (NASA TM 88227, 1986). The simulations were performed using equilibrium and non-equilibrium wall models. The agreement with experiment is encouraging for the finest grid with respect to the separation bubble length, unsteady shock structure and wall pressure distribution. Sensitivity ofWMLES results to grid, wall model, and blockage effects in the tunnel are reported.
Iyer, Prahladh S.↗
Wall-Resolved Large-Eddy Simulations of Transonic Shock-Induced Flow Separation
Wall-resolved large-eddy simulations of shock-induced flow separation over an axisymmet- ric bump for a Mach number of 0.875 and a chord-based Reynolds number of 2.763 million are performed. The incoming boundary layer has a momentum-thickness Reynolds number of 6600 at 1.5 chords upstream of the bump. The calculations, which employ up to 24 billion grid points, simulate the experimental model of Bachalo and Johnson (AIAA Journal, Vol. 24, No. 3, 1986), except that the tunnel walls are ignored and free air is assumed. The effects of domain span and grid resolution are examined along with the main flowfield features. The predicted shock position as well as separation and reattachment locations agree well with the experiment. Grid convergence is observed in the attached region well upstream of separation. Two-point azimuthal correlations suggest that a span of at least 20 degrees is needed in the attached region, while a 120-degree span might be barely large enough in the separated region. Computed root-mean-square surface pressure fluctuations at the shock foot reach about 5 percent of ambient pressure and the level at reattachment location drops to about half of the primary peak. Simulations reveal evidence of the low-frequency shock unsteadiness; however, a much longer statistical sample is needed to investigate this phenomenon.
Uzun, Ali↗
Wall-Resolved Large Eddy Simulations of Transonic Shock-Induced Flow Separation
This paper reports the wall-resolved large eddy simulations of shock-induced boundary layer separation over an axisymmetric bump for a flow Mach number of 0.875 and a chord-based Reynolds number of 2.763 million. The incoming boundary layer has a momentum-thickness Reynolds number of 6600 at one and a half chord lengths upstream of the leading edge. The calculations simulate the experiment by Bachalo and Johnson (AIAA Journal, Vol. 24, No. 3, 1986), except that the tunnel walls are ignored and the simulations are performed assuming free air with as many as 24 billion grid points. The effects of domain span, grid resolution and time step on the predictions are examined. The results are found to show some sensitivity to the studied parameters. Owing to the outer boundary conditions, the predicted surface pressure distribution as well as the flow separation and reattachment locations tend to agree better with the experimental results from the larger (6 × 6 ft) tunnel than those from the smaller (2 × 2 ft) tunnel. The predicted Reynolds shear stress profiles in the separated region differ by as much as 31%from the experimental results that were only obtained in the smaller tunnel. The most accurate surface pressure distribution obtained in this study lies within the scatter of the measurements taken in the two facilities.
Uzun, Ali↗
Wall-Resolved Large-Eddy Simulation of Flow Separation Over NASA Wall-Mounted Hump
This paper reports the findings from a study that applies wall-resolved large-eddy simulation to investigate flow separation over the NASA wall-mounted hump geometry. Despite its conceptually simple flow configuration, this benchmark problem has proven to be a challenging test case for various turbulence simulation methods that have attempted to predict flow separation arising from the adverse pressure gradient on the aft region of the hump. The momentum-thickness Reynolds number of the incoming boundary layer has a value that is near the upper limit achieved by recent direct numerical simulation and large-eddy simulation of incompressible turbulent boundary layers. The high Reynolds number of the problem necessitates a significant number of grid points for wall-resolved calculations. The present simulations show a significant improvement in the separation-bubble length prediction compared to Reynolds-Averaged Navier-Stokes calculations. The current simulations also provide good overall prediction of the skin-friction distribution, including the relaminarization observed over the front portion of the hump due to the strong favorable pressure gradient. We discuss a number of problems that were encountered during the course of this work and present possible solutions. A systematic study regarding the effect of domain span, subgrid-scale model, tunnel back pressure, upstream boundary layer conditions and grid refinement is performed. The predicted separation-bubble length is found to be sensitive to the span of the domain. Despite the large number of grid points used in the simulations, some differences between the predictions and experimental observations still exist (particularly for Reynolds stresses) in the case of the wide-span simulation, suggesting that additional grid resolution may be required.
Uzun, Ali↗
Wall-Modeled Large Eddy Simulation of Flow Past a Wall-Mounted Hump
No abstract available
Iyer, Prahladh S.↗
CFD Vision 2030 CFD Study: A Pathway to Revolutionary Computational Aerosciences
No abstract available
Malik, Mujeeb R.↗
Towards Bridging the Gaps in Holistic Transition Prediction via Numerical Simulations
The economic and environmental benefits of laminar flow technology via reduced fuel burn of subsonic and supersonic aircraft cannot be realized without minimizing the uncertainty in drag prediction in general and transition prediction in particular. Transition research under NASA's Aeronautical Sciences Project seeks to develop a validated set of variable fidelity prediction tools with known strengths and limitations, so as to enable "sufficiently" accurate transition prediction and practical transition control for future vehicle concepts. This paper provides a summary of selected research activities targeting the current gaps in high-fidelity transition prediction, specifically those related to the receptivity and laminar breakdown phases of crossflow induced transition in a subsonic swept-wing boundary layer. The results of direct numerical simulations are used to obtain an enhanced understanding of the laminar breakdown region as well as to validate reduced order prediction methods.
Choudhari, Meelan M.↗
Boundary-Layer Stability Analysis of the Mean Flows Obtained Using Unstructured Grids
Boundary-layer stability analyses of mean flows extracted from unstructured-grid Navier- Stokes solutions have been performed. A procedure has been developed to extract mean flow profiles from the FUN3D unstructured-grid solutions. Extensive code-to-code validations have been performed by comparing the extracted mean ows as well as the corresponding stability characteristics to the predictions based on structured-grid solutions. Comparisons are made on a range of problems from a simple at plate to a full aircraft configuration-a modified Gulfstream-III with a natural laminar flow glove. The future aim of the project is to extend the adjoint-based design capability in FUN3D to include natural laminar flow and laminar flow control by integrating it with boundary-layer stability analysis codes, such as LASTRAC.
Liao, Wei↗
Computational Analysis of the G-III Laminar Flow Glove
Under NASA's Environmentally Responsible Aviation Project, flight experiments are planned with the primary objective of demonstrating the Discrete Roughness Elements (DRE) technology for passive laminar flow control at chord Reynolds numbers relevant to transport aircraft. In this paper, we present a preliminary computational assessment of the Gulfstream-III (G-III) aircraft wing-glove designed to attain natural laminar flow for the leading-edge sweep angle of 34.6deg. Analysis for a flight Mach number of 0.75 shows that it should be possible to achieve natural laminar flow for twice the transition Reynolds number ever achieved at this sweep angle. However, the wing-glove needs to be redesigned to effectively demonstrate passive laminar flow control using DREs. As a by-product of the computational assessment, effect of surface curvature on stationary crossflow disturbances is found to be strongly stabilizing for the current design, and it is suggested that convex surface curvature could be used as a control parameter for natural laminar flow design, provided transition occurs via stationary crossflow disturbances.
Malik, Mujeeb R.↗
Roughness Based Crossflow Transition Control for a Swept Airfoil Design Relevant to Subsonic Transports
A high fidelity transition prediction methodology has been applied to a swept airfoil design at a Mach number of 0.75 and chord Reynolds number of approximately 17 million, with the dual goal of an assessment of the design for the implementation and testing of roughness based crossflow transition control and continued maturation of such methodology in the context of realistic aerodynamic configurations. Roughness based transition control involves controlled seeding of suitable, subdominant crossflow modes in order to weaken the growth of naturally occurring, linearly more unstable instability modes via a nonlinear modification of the mean boundary layer profiles. Therefore, a synthesis of receptivity, linear and nonlinear growth of crossflow disturbances, and high-frequency secondary instabilities becomes desirable to model this form of control. Because experimental data is currently unavailable for passive crossflow transition control for such high Reynolds number configurations, a holistic computational approach is used to assess the feasibility of roughness based control methodology. Potential challenges inherent to this control application as well as associated difficulties in modeling this form of control in a computational setting are highlighted. At high Reynolds numbers, a broad spectrum of stationary crossflow disturbances amplify and, while it may be possible to control a specific target mode using Discrete Roughness Elements (DREs), nonlinear interaction between the control and target modes may yield strong amplification of the difference mode that could have an adverse impact on the transition delay using spanwise periodic roughness elements.
Li, Fei↗
Analysis of Crossflow Transition Flight Experiment aboard the Pegasus Launch Vehicle
The Pegasus wing-glove flight experiment was designed to provide crossflow transition data at high Mach numbers, specifically to help validate stability based predictions for transition onset in a flight environment. This paper provides an analysis of the flight experiment, with emphasis on computational results for crossflow disturbances and the correlation of disturbance growth factors with in-flight transition locations via the e(sup N) method. Implications of the flight data for attachment line stability are also examined. Analysis of the thermocouple data reveals that transition (from turbulent to laminar flow) was first detected during the ascending flight of the rocket when the free stream Mach number exceeded about 4. Therefore, computations have been performed for flight Mach numbers of 4.13, 4.35, 4.56 and 4.99. Due to continually decreasing unit Reynolds number at higher altitudes, the entire wing-glove boundary layer became laminar at the highest flight Mach number computed above. In contrast, the boundary layer flow over the inboard tile region remained transitional up to and somewhat beyond the time of laminarization over the instrumented glove region. Linear stability predictions confirmed that the tile boundary layer is indeed more unstable to crossflow disturbances than the much colder stainless steel glove boundary layer. The transition locations based on thermocouple data from both the glove and the tile regions are found to correlate with stationary-crossflow N-factors within the range of 7 to 12.4 and with traveling mode N-factors between 7.6 and 14.1. Data from the thermocouples and hot film sensors indicates that transition from turbulent to laminar flow (i.e., laminarization) at a fixed point over the glove is generally completed within a flight time interval of 3 seconds. However, the times at which transition begins and ends as inferred from the hot film sensors are found to differ by about 2 seconds from the corresponding estimates based on the thermocouple data.
Malik, Mujeeb R.↗
Acoustic Receptivity of Mach 4.5 Boundary Layer with Leading- Edge Bluntness
Boundary layer receptivity to two-dimensional slow and fast acoustic waves is investigated by solving Navier-Stokes equations for Mach 4.5 flow over a flat plate with a finite-thickness leading edge. Higher order spatial and temporal schemes are employed to obtain the solution whereby the flat-plate leading edge region is resolved by providing a sufficiently refined grid. The results show that the instability waves are generated in the leading edge region and that the boundary-layer is much more receptive to slow acoustic waves (by almost a factor of 20) as compared to the fast waves. Hence, this leading-edge receptivity mechanism is expected to be more relevant in the transition process for high Mach number flows where second mode instability is dominant. Computations are performed to investigate the effect of leading-edge thickness and it is found that bluntness tends to stabilize the boundary layer. Furthermore, the relative significance of fast acoustic waves is enhanced in the presence of bluntness. The effect of acoustic wave incidence angle is also studied and it is found that the receptivity of the boundary layer on the windward side (with respect to the acoustic forcing) decreases by more than a factor of 4 when the incidence angle is increased from 0 to 45 deg. However, the receptivity coefficient for the leeward side is found to vary relatively weakly with the incidence angle.
Malik, Mujeeb R.↗
Receptivity of Supersonic Boundary Layers to Acoustic Disturbances
Boundary layer receptivity to two-dimensional slow and fast acoustic waves is investigated by solving Navier-Stokes equations for Mach 4.5 flow over a flat plate with a finite-thickness leading edge. Higher order spatial and temporal schemes are employed to obtain the solution whereby the flat-plate leading edge region is resolved by providing a sufficiently refined grid. The results show that the instability waves are generated in the leading edge region and that the boundary-layer is much more receptive to slow acoustic waves (by almost a factor of 20) as compared to the fast waves. Hence, this leading-edge receptivity mechanism is expected to be more relevant in the transition process for high Mach number flows. The effect of acoustic wave incidence angle is also studied and it is found that the receptivity of the boundary layer on the windward side (with respect to the acoustic forcing) decreases by more than a factor of 4 when the incidence angle is increased from 0 to 45 deg. However, the receptivity coefficient for the leeward side is found to vary relatively weakly with the incidence angle. The effect of leading-edge thickness is also studied and bluntness is found to stabilize the boundary layer. The relative significance of fast acoustic waves is enhanced in the presence of bluntness.
Malik, Mujeeb R.↗
Unsteady Simulation of a Landing-Gear Flow Field
This paper presents results of an unsteady Reynolds-averaged Navier-Stokes simulation of a landing-gear flow field. The geometry of the four-wheel landing gear assembly consists of several of the fine details including the oleo-strut, two diagonal struts, a door, yokes/pin and a flat-plate simulating the wing surface. The computational results, obtained by using 13.3 million grid points, are presented with an emphasis on the characteristics of the unsteadiness ensuing from different parts of the landing-gear assembly, including vortex shedding patterns and frequencies of dominant oscillations. The results show that the presence of the diagonal struts and the door significantly influence the flow field. Owing to the induced asymmetry, vortices are shed only from one of the rear wheels and not the other. Present computations also capture streamwise vortices originating from the upstream corners of the door.
Li, Fei↗
Linear and nonlinear PSE for compressible boundary layers
Compressible stability of growing boundary layers is studied by numerically solving the partial differential equations under a parabolizing approximation. The resulting parabolized stability equations (PSE) account for nonparallel as well as nonlinear effects. Evolution of disturbances in compressible flat-plate boundary layers are studied for freestream Mach numbers ranging from 0 to 4.5. Results indicate that the effect of boundary-layer growth is important for linear disturbances. Nonlinear calculations are performed for various Mach numbers. Two-dimensional nonlinear results using the PSE approach agree well with those from direct numerical simulations using the full Navier-Stokes equations while the required computational time is less by an order of magnitude. Spatial simulation using PSE were carried out for both the fundamental and subharmonic type breakdown for a Mach 1.6 boundary layer. The promising results obtained show that the PSE method is a powerful tool for studying boundary-layer instabilities and for predicting transition over a wide range of Mach numbers.
Chang, Chau-Lyan↗