A Corrosion Test Station for Improved Characterization and Examination Capabilities of Advanced Nuclear Reactor Fuels and Materials
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Maloy, Stuart.
Explore the source record for details and available documents.
The cold spray deposition process has been investigated for the manufacture of 14YWT oxide-dispersion strengthened (ODS) steel, a nanostructured ferritic alloy (NFA), using gas-atomized and ball-milled feedstock powders. Cold spraying of the gas-atomized powder resulted in a thick dense deposit, but annealing them above 900 °C induced grain growth and heterogeneous precipitation of nanoparticles, thus resulting in lower hardness (~ 170 HV) compared to 14YWT ODS steel manufactured by the conventional method. The ball-milled powder (Fe-14Cr-3W-0.4Ti-0.2Y-0.125O) was cryomilled in liquid N 2 to achieve small particle sizes followed by annealing in a H 2 /Ar environment at 1000 °C and 1100 °C to reduce the hardness from ~ 8 GPa to ~ 5 GPa. Both smaller particle sizes and lower hardness of annealed powders made them amenable to the cold spray deposition process, resulting in thick and dense deposits, while retaining the favorable fully solutionized microstructure of the ball-milled powders. The microstructure of the as-deposited ODS exhibited very fine grain sizes (50–250 nm) with a uniform dispersion of Y-Ti-O nanoprecipitates in the ferritic steel matrix. The hardness values of the cold spray deposits using the powders annealed at 1000 °C and 1100 °C was 770 HV and 496 HV, respectively. Post-heat treatment of the as-deposited material up to 1100 °C showed a high-density microstructure with uniformly dispersed nanoscale oxide particles. The hardness of the annealed deposits up to 1000 °C had a notably higher hardness than bulk 14YWT ODS steel manufactured by conventional methods. The study demonstrates that cold spray deposition of the microstructurally-tailored feedstock powders can be used to successfully manufacture ODS steel with microstructure and properties comparable to those produced by the conventional methods, while providing for an attractive option for the more rapid and cost-effective manufacturing of ODS steel cladding tubes.
Explore the source record for details and available documents.
An external report as highlight for the NSUF program
The nanostructured ferritic alloy 14YWT is a promising candidate for in-core use in generation IV nuclear reactors, due to a dense dispersion of insoluble, ultrafine-scale Y-Ti-O nano-oxides, which provide a high degree of irradiation tolerance and thermal stability. This work investigates the effects of heat treatment on the workability of 14YWT, along with the effect of processing history on abnormal grain structures and radial microstructural uniformity. In this study, a 14YWT rod consolidated at 850 °C was heat treated in argon at 1100 °C, 1150 °C, 1200 °C, or 1250 °C for 1 or 8 hours and changes in mechanical properties and microstructure were examined using microhardness and electron backscattered diffraction (EBSD). Two distinct types of large abnormal grains were observed, each with unique processing origins, including one with high and the other with low strain energy. Consolidation via direct extrusion resulted in radial microstructural gradients, where the center of the rod was softer with larger grain sizes and lower strain energies. These gradients persisted and intensified throughout heat treatment. Based upon this work, the recommended heat treatment for increased workability with minimal microstructural change is 1150 °C for 1 hours.
Ferritic/martensitic steels, such as HT-9, are known for their complex microstructural features and mechanical properties. Here in this paper, in-situ micro-tensile tests and traditional fractography methods were utilized to study the fracture behavior of proton-irradiated HT-9 steels. First, to evaluate the viability of micro-tensile tests for nuclear material qualification process, meso-tensile tests on as-received HT-9 steels were performed. Fracture mechanisms of unirradiated HT-9 steels at both length scales were compared and underlying mechanisms discussed. The direct comparison of micro- and meso-scale data shows a distinctive size effect demonstrated by the increase in yield stress (YS). Upon completion of initial assessment, specimens were irradiated with 4 MeV + protons to three fluences, all of which were lower than 0.01 displacements per atom (dpa). As expected, the YS increases with irradiation. However, at 7 × 10 -3 dpa, the reversal of the trend was observed, and the YS exhibited sharp decline. We demonstrate that at lower length scales, grain structure has a more profound impact on the mechanical properties of irradiated materials, which provides information needed to fill in the gap in current understanding of the HT-9 fracture at different length scales.
This computer code uses the concept of the parallax to compute the x, y and z coordinates of points found using transmission electron microscopy (TEM), or any transmission imaging technique, using two images, each taken at a different perspective of the region containing the points. Points correspond, but are not limited, to the center of cavities or precipitates, positions of irradiation black dot damage, positions along a dislocation line, or positions along where an interface meets a free surface. Features can include dislocations, interfaces, cavities, precipitates, inclusions etc. The x, y and z coordinates of the points are output in a text file. The code also allows the user to visualize the features containing the points in three dimensions.
Ferritic/martensitic steels are one of the best candidates for structural materials for high dose applications in next generation nuclear reactors. The composition of structural materials must be optimized for reliable service during irradiation. This study reports the effect of interstitial nitrogen on radiation response in 12Cr ferritic/martensitic HT9 steels having a controlled nitrogen concentration. Results show that a high amount of ‘free’ nitrogen in the matrix stabilizes the interstitial clusters which leads to (i) larger loop sizes (ii) lower loop density and (iii) slightly reduced radiation induced hardening. It also affects diffusion mechanism of Ni and formation of Ni/Si-rich precipitates.
The cold spray materials deposition process has been explored for manufacturing oxide dispersion-strengthened (ODS) steel fuel cladding tubes. Gas-atomized 14YWT ODS steel powder was used as the feedstock material. A parametric investigation of the cold spray process involving substrate materials of various hardnesses, gas preheat temperatures, and carrier gas compositions was performed to gain the highest quality deposit. The high-velocity impact of the powder on the substrate led to dissolution of discrete oxide nanoparticles, which subsequently reprecipitated during postdeposition annealing at high temperatures. The tubes were manufactured by deposition on an Al-alloy mandrel substrate and subsequent chemical dissolution of the substrate. A 204-mm-long and 1-mm-thick ODS steel cladding tube was successfully manufactured. The grain growth and distribution of oxide nanoparticles in ferritic steel matrix were identified at elevated temperatures. In general, the cold spray process holds considerable promise for rapid, cost-effective manufacturing of ODS steel cladding tubes.
Explore the source record for details and available documents.
Three papers are attached highlighting some recent progress in the development and testing of Oxide Dispersion Strengthened ferritic steels in tube and plate form. Aydogan et al. (2016) and Alam et al. (2016) papers summarize testing and characterization that has been performed on plate and tube materials. In the Alam et al. paper it was noted that after cross-rolling plate material of 14YWT, microcracks were formed. This resulted from an (001) texture in the plane normal to the plate causing cracking microcracking within that plane. Such microcracking affects low temperature tensile properties up to 200C. It was not seen in tube material produced by hydrostatic extrusion. In the Aydogan et al. (2016) paper characterization was performed on tubes produced from the ODS material, 14YWT. Tubes were formed through hydrostatic extrusion of plate material and hydrostatic extrusion of spray formed tubes. It was noted that strong texture on {001}<110> was formed in the plate material while shear deformation during hot extrusion produced a strong <111> ll ND texture component. In the Aydogan et al. (2017) paper detailed analysis was performed on the change in oxide size with ion irradiation to doses >500 dpa at 450C. The results show strong stability for the 2-4 nm oxide particles with a reduction in size ~25% after 270 dpa and an increase in density.
High temperature mechanical measurements were conducted to study the effect of the dynamic precipitation process of PH 13-8 Mo maraging steel. Yield stress, ultimate tensile strength, total elongation, hardness, strain rate sensitivity and activation volume were evaluated as a function of the temperature. The dynamic changes in the mechanical properties at different temperatures were evaluated and a balance between precipitation hardening and annealed softening is discussed. A comparison between hardness and yield stress and ultimate tensile strength over a temperature range from 300 to 600 °C is made. The behavior of the strain rate sensitivity was correlated with the intermetallic precipitates formed during the experiments.
High temperature mechanical measurements were conducted to study the effect of the dynamic precipitation process of PH 13-8 Mo maraging steel. Yield stress, ultimate tensile strength, total elongation, hardness, strain rate sensitivity and activation volume were evaluated as a function of the temperature. The dynamic changes in the mechanical properties at different temperatures were evaluated and a balance between precipitation hardening and annealed softening is discussed. A comparison between hardness and yield stress and ultimate tensile strength over a temperature range from 300 to 600 °C is made. The behavior of the strain rate sensitivity was correlated with the intermetallic precipitates formed during the experiments.