Engineering topics

Mamalis, Sotirios

Publications and source records attributed to Mamalis, Sotirios.

3 records

DOE OSTI2020

Falling-film thermosyphons: Application to water harvesting from humid gas streams

Water harvesting from humid gas streams is central to fresh-water production, desalination, and particulate removal from combustion gas streams. Two-phase thermosyphons are well suited for these applications due to their very low thermal resistance, but have several operating limits at the high heat flows required for such applications. This work introduces the falling-film thermosyphon for large-scale condensation applications. Working fluid is pumped to the top of the evaporator to provide the evaporating liquid film on the inner tube wall, rather than by vapor condensation. The flooding, dry-out and pool-boiling limits are eliminated, resulting in significantly higher maximum heat fluxes for the same physical evaporator size. Furthermore, the condenser no longer needs to be located vertically above the evaporator, which allows for a standard steam condenser to be used. A model for the condensation process in humid air was developed that estimates the fluid and heat transfer and is confirmed experimentally. Further benefits include the use of a high-thermal-conductivity polymer material for the evaporator section to minimize corrosion, and the ability to impose a temperature boundary condition on the evaporator, which is made possible due to the elimination of a liquid pool.

42 ENGINEERING↗

DOE OSTI2020

Experimental Study of the Effect of Start of Injection and Blend Ratio on Single Fuel Reformate RCCI

Abstract A new concept of single fuel reactivity-controlled compression ignition (RCCI) has been proposed through the catalytic partial oxidation (CPOX) reformation of diesel fuel. The reformed fuel mixture is then used as the low reactivity fuel and diesel itself is used as the high reactivity fuel. In this paper, two reformate mixtures from the reformation of diesel were selected for further analysis. Each reformate fuel mixture contained a significant fraction of inert gases (89% and 81%). The effects of the difference in the molar concentrations of the reformate mixtures were studied by experimenting with diesel as the direct injected fuel in RCCI over a varying start of injection timings and different blend ratios (i.e., the fraction of low and high reactivity fuels). The reformate mixture with the lower inert gas concentration had earlier combustion phasing and shorter combustion duration at any given diesel start of injection timing. The higher reactivity separation between reformate mixture and diesel, compared with gasoline and diesel, causes the combustion phasing of reformate-diesel RCCI to be more sensitive to the start of injection timing. The maximum combustion efficiency was found at a CA50 before top dead center (TDC), whereas the maximum thermal efficiency occurs at a CA50 after TDC. The range of energy-based blend ratios in which reformate-diesel RCCI is possible is between 25% and 45%, limited by ringing intensity (RI) at the low limit of blend ratios, and coefficient of variance (COV) of net indicated mean effective pressure (IMEPn) and combustion efficiency at the high limit. Intake boosting becomes necessary due to the oxygen deficiency caused by the low energy density of the reformate mixtures as it displaces intake air.

Engineering↗

DOE OSTI2019

Single-fuel reactivity controlled compression ignition through catalytic partial oxidation reformation of diesel fuel

A single-fuel RCCI concept has been proposed to avoid the need for a secondary fuel system required for conventional RCCI by generating the secondary fuel from the primary fuel through catalytic partial oxidation (CPOX) reformation. In conventional RCCI, gasoline or natural gas can be used as the low-reactivity fuel, and diesel can be used as the high-reactivity fuel. In this study, two reformate mixtures generated by reforming diesel fuel at different operating conditions were used as the low-reactivity fuel, with the parent diesel as the high reactivity fuel. The combustion characteristics of reformate-diesel RCCI were compared with the conventional RCCI. A CFD model was also developed and validated against the experimental results. The model was then used to validate a necessary approximation of the reformate mixture's species concentrations. Compared to conventional RCCI fuel pairs, reformate-diesel RCCI shows marginally better thermal efficiency, approximately 10% better THC emissions, approximately 50% lower NOx emissions, and good controllability. Because the reformate mixture has a high concentration of diluents it displaces a large fraction of intake air and acts similarly to EGR. The combustion behavior of reformate-diesel RCCI is in between that of gasoline-diesel and natural gas-diesel conventional RCCI. From the results, it can be concluded that reformate-diesel RCCI is not overly sensitive to the reformation process itself and the exact species concentrations in the reformate mixture. Finally, a small change in the start of injection of diesel, blend ratio, and EGR fraction can be used to compensate for reformate mixture concentration differences.

33 ADVANCED PROPULSION SYSTEMS↗