Search NASA⌕ Search

Engineering topics

Mangla, Sundeep

Publications and source records attributed to Mangla, Sundeep.

A helical actuator driven by biased SMA: design, model, and experiment

A helical actuator driven by biased shape memory alloy (SMA) patterns embedded into a soft composite ribbon base is presented in this work. Instead of common U-shape SMA wires, a single SMA wire is woven into planar patterns, which enable helical deformation of the composite ribbon from an initially flat geometry. An analytical static model is established for accurate and rapid prediction of the helical reconfiguration arising from the shape memory effect of woven SMA patterns, followed by validation of the static model using the finite element method (FEM). The finite element results are compared with the analytical solutions given by this static model, which show a high agreement. Parametric study of the influences of eight independent design variables on the dependent helical parameters, such as combined curvatures, pitches, and helical angles, is completed. It is found that the helically deformed geometry is mainly dominated by diameters, biased positions, inclined angles, and numbers of skewed segments of the SMA wire. Fabrication and in-situ experimental test of a prototype of such helical actuators qualitatively demonstrate its dramatic three-dimensional (3D) spiral reconfiguration from a two-dimensional (2D) flat ribbon. In conclusion, such SMA patterns will allow more diverse designs of soft actuators for a wider range of robotic applications.

36 MATERIALS SCIENCE↗

Smart material based multilayered microbeam structures for spatial self-deployment and reconfiguration: A residual stress approach

Alleviation of the potentially damaging effects induced by residual stresses was comprehensively investigated in previous research. Here, this paper, however, presents a spatially self-deployable and reconfigurable multilayered microbeam which takes advantage of residual stresses and shape memory effects. Reconfigurable mechanism of a typical four-layered microbeam composed of Pt\Ni 50 Ti 50 \Ni 50 Ti 50 \Pt is introduced, followed by analytical modeling of the maximum distance of the self-deployed gap as functions of variable structural and material parameters, including compressive residual stress in Pt layers and tensile residual stress in Ni 50 Ti 50 layers. Analytical solutions given by the static model agree well with the results obtained via finite element models (FEMs). Fabrication, characterization, and in-situ experiments were carried out to validate the feasibility of deployment of the as-released four-layered microbeam. The maximum distance of the gap was measured to be 41.39 μm at 20 °C, which could be increased to 51.73 μm thanks to controllable reconfiguration driven by shape memory effects. Theoretical analysis of such self-deployment and reconfiguration suggested a tensile residual stress increase by 52 MPa in Ni 50 Ti 50 layers. The multilayered microbeam structure with capabilities of self-deployment and reconfiguration offers great potential for various emerging applications, such as micro robotics, medical drug delivery devices, and intelligent chip scale spacecraft.

36 MATERIALS SCIENCE↗

Multilayered microstructures with shape memory effects for vertical deployment

This paper presents a fabrication and characterization of multilayered microstructures with shape memory effects enabling large vertical deployment under electro-thermal actuation. Our previous research demonstrated vertical deployment of such microstructures by the effect of thermal mismatch. Development of equiatomic NiTi layers in the multilayered microstructure is investigated further for shape memory effects. Multilayered microstructures are built by sputtered NiTi layers and a lift-off process. Negative photoresist ma-N1420 enables clean lift-off of 500 nm thick NiTi layers by forming a significant undercut profile after development. The parametric study on co-sputter powers for Ti and Ni 50 Ti 50 targets suggests that 100 W RF on Ti target and 200 W DC on Ni 50 Ti 50 target can deposit Ni 49.62 Ti 50.38 layers. X-Ray Diffraction (XRD) and Atomic Force Microscopy (AFM) were used to study the crystal structures and surface topography of NiTi layers. XRD results of post-annealed Ni 49.62 Ti 50.38 layers show coexistence of austenite and martensitic phases at room temperature, suggesting that the transformation temperature of such NiTi layers should be approximate 20 °C. The surface topography of Ni 49.62 Ti 50.38 layers reveals substantial increase of surface roughness at ambient conditions after the annealing. Experimental verification of the multilayered microstructure for vertical deployment was carried out by Signatone Probe Station and Dual Scanning Electron Microscope/Focused Ion Beam (SEM/FIB) system. Finally, a vertical deployment of the two-dimensional (2D) multilayered microstructures for three-dimensional (3D) can be detected by applying a constant voltage of 0.04 V, and the expected 3D deployment displacement is enlarged from 2 μm to 10 μm by introducing the shape memory effect.

42 ENGINEERING↗

Thermo-mechanical modeling and experimental validation for multilayered metallic microstructures

This paper presents thermo-mechanical modeling on multilayered metallic microstructures consisting of two bilayers that enable 3D deployment once being Joule heated. Additionally, a representative design of such microstructures, as well as their working principle is introduced. Furthermore, a mathematical model is derived using Euler–Bernoulli beam theory, and analytical solutions describing out-of-plane displacement of the multilayered microstructures when uniformly heated, which is validated by finite element analysis. Parametric analysis on thermal load and dimensional change of beam shows a good agreement between the analytical solutions and results given by finite element analysis. The phases of the near-equiatomic NiTi layer are analyzed by EDS and XRD, which prove to be austenite during the Joule heating process. The mechanical properties of austenite NiTi are incorporated into the analytical solutions that provides a good estimation of 3D deployment of microstructures made of NiTi and aluminum. The experimental results provide an approximately 7 µm out-of-plane deployment by applying a uniform temperature increase of 132 K, and parametric analysis on the dimension of top aluminum beam offers another promising approach to larger 3D deployment. The proposed mathematical model provides an efficient tool for predicting the out-of-plane deployment of such multilayered microstructures.

36 MATERIALS SCIENCE↗