Search NASA⌕ Search

Engineering topics

Mangum, John S.

Publications and source records attributed to Mangum, John S..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

GdWN 3 is a nitride perovskite

Nitride perovskites ABN3 are an emerging and highly underexplored class of materials that are of interest due to their intriguing calculated ferroelectric, optoelectronic, and other functional properties. Incorporating novel A-site cations is one strategy to tune and expand such properties; for example, Gd 3+ is compelling due to its large magnetic moment, potentially leading to multiferroic behavior. However, the theoretically predicted ground state of GdWN 3 was a non-perovskite monoclinic structure. Here, we experimentally show that GdWN 3-y crystallizes in a perovskite structure. High-throughput combinatorial sputtering with activated nitrogen is employed to synthesize thin films of Gd 2-x W x N 3-y O y with oxygen content y < 0.05. Ex situ annealing crystallizes a polycrystalline perovskite phase in a narrow composition window near x = 1. LeBail fits of synchrotron grazing incidence wide angle x-ray scattering data are consistent with a perovskite ground-state structure. Refined density functional theory calculations that included antiferromagnetic configurations confirm that the ground-state structure of GdWN 3 is a distorted Pnma perovskite with antiferromagnetic ordering, in contrast to prior predictions. Initial property measurements find that GdWN 3-y is paramagnetic down to T = 2 K with antiferromagnetic correlations and that the absorption onset depends on cation stoichiometry. This work provides an important path toward both the rapid expansion of the emerging family of nitride perovskites and understanding their potential multiferroic properties.

14 SOLAR ENERGY↗
DOE OSTI2024

Low‐Temperature Synthesis of Stable CaZn 2 P 2 Zintl Phosphide Thin Films as Candidate Top Absorbers

Abstract The development of tandem photovoltaics and photoelectrochemical solar cells requires new absorber materials with bandgaps in the range of ≈1.5–2.3 eV, for use in the top cell paired with a narrower‐gap bottom cell. An outstanding challenge is finding materials with suitable optoelectronic and defect properties, good operational stability, and synthesis conditions that preserve underlying device layers. This study demonstrates the Zintl phosphide compound CaZn 2 P 2 as a compelling candidate semiconductor for these applications. Phase‐pure, ≈500 nm‐thick CaZn 2 P 2 thin films are prepared using a scalable reactive sputter deposition process at growth temperatures as low as 100 °C, which is desirable for device integration. Ultraviolet‐visible spectroscopy shows that CaZn 2 P 2 films exhibit an optical absorptivity of ≈10 4 cm −1 at ≈1.95 eV direct bandgap. Room‐temperature photoluminescence (PL) measurements show near‐band‐edge optical emission, and time‐resolved microwave conductivity (TRMC) measurements indicate a photoexcited carrier lifetime of ≈30 ns. CaZn 2 P 2 is highly stable in both ambient conditions and moisture, as evidenced by PL and TRMC measurements. Experimental data are supported by first‐principles calculations, which indicate the absence of low‐formation‐energy, deep intrinsic defects. Overall, this study shall motivate future work integrating this potential top cell absorber material into tandem solar cells.

14 SOLAR ENERGY↗
DOE OSTI2024

Sn-assisted heteroepitaxy improves ZnTiN 2 photoabsorbers

Ambient temperature growth on Si produces a polycrystalline ZnTiN 2 film while Sn-assisted growth on sapphire at elevated temperature results in a single-crystal-like ZnTiN 2 film with significantly reduced sub-bandgap absorption.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Autonomous sputter synthesis of thin film nitrides with composition controlled by Bayesian optimization of optical plasma emission

Autonomous experimentation has emerged as an efficient approach to accelerate the pace of material discovery. Although instruments for autonomous synthesis have become popular in molecular and polymer science, solution processing of hybrid materials, and nanoparticles, examples of autonomous tools for physical vapor deposition are scarce yet important for the semiconductor industry. Here, we report the design and implementation of an autonomous workflow for sputter deposition of thin films with controlled composition, leveraging a highly automated sputtering reactor custom-controlled by Python, optical emission spectroscopy (OES), and a Bayesian optimization algorithm. We modeled film composition, measured by x-ray fluorescence, as a linear function of plasma emission lines monitored during co-sputtering from elemental Zn and Ti targets in an N 2 and Ar atmosphere. A Bayesian control algorithm, informed by OES, navigates the space of sputtering power to fabricate films with user-defined compositions by minimizing the absolute error between desired and measured optical emission signals. We validated our approach by autonomously fabricating Zn x Ti 1-x N y films that deviate from the targeted cation composition by a relative ±3.5%, even for 15 nm thin films, demonstrating that the proposed approach can reliably synthesize thin films with a specific composition and minimal human interference. Moreover, the proposed method can be extended to more difficult synthesis experiments where plasma intensity lines depend non-linearly on pressure, or the elemental sticking coefficients strongly depend on the substrate temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multimodal microscopy of extended defects in β-Ga 2 O 3 (010) EFG crystals

Beta-phase gallium oxide (β-Ga 2 O 3 ) has attracted attention in recent years as a potentially low cost, large area substrate and active layer material for high power, high temperature power electronics and sensing devices. However, growth of β-Ga 2 O 3 crystals is complicated by easily activated (100) and (001) cleavage planes, the presence of low angle grain boundaries (LAGBs) and twins, and the potential formation of polycrystalline grains. In this study, β-Ga 2 O 3 crystals were grown by the edge-defined film-fed growth technique with an (010) principal face. Two crystals with apparently randomly formed high angle grain boundaries (HAGBs) were selected and analyzed by electron backscatter diffraction, electron channeling contrast imaging, and cathodoluminescence to investigate the nature of the LAGBs and the source of the HAGB formation. It was discovered that planar LAGBs lying parallel to the (010) plane exist in the region immediately preceding the start of an HAGB. Increased misorientation across the LAGB was observed, approaching the initiation of a new grain. We present multimodal microscopy characterization, correlating misorientation and variation in optoelectronic properties with LAGBs and the associated dislocations.

14 SOLAR ENERGY↗
DOE OSTI2023

Thin-film TaAs: Developing a platform for Weyl semimetal devices

MX monopnictide compounds (M = Nb,Ta, X = As,P) are prototypical 3D Weyl semimetals (WSMs) that have been shown in bulk single crystal form to have potential for a wide variety of novel devices due to topologically protected band structures and high mobilities. However, very little is known about thin-film synthesis, which is essential to enable device applications. We synthesize TaAs(001) epilayers by molecular beam epitaxy on GaAs(001) and provide an experimental phase diagram illustrating conditions for single-phase, single-crystal-like growth. We investigate the relationship between nanoscale defects and electronic structure using angle-resolved photoemission spectroscopy, kelvin probe force microscopy, and transmission electron microscopy. Our results provide a roadmap and platform for developing 3D WSMs for device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Correspondence: Bill of Materials Variation and Module Degradation in Utility-Scale PV Systems

We report photovoltaic (PV) modules of the same make and model are often assembled with different bills of materials (BOMs). In this correspondence, we revisit two case studies of utility-scale silicon PV systems in which these differing BOMs were associated with faster-than-expected degradation. In one of the sites, we found that different metallization paste had been used for grid lines in some cells leading to loss of contact to the cell and severe series resistance degradation. We provide details on the observation of this mechanism at two additional sites not described in the original article. In a second case study, we found that two different types of cell had been used, and that they could be distinguished by their back contact. Cells with uniform back contacts suffered from light and elevated temperature induced degradation (LeTID), while those with local back contacts did not. We also briefly describe BOM variations observed at other sites to illustrate the extent of the challenge. Our results from both sites underscore that variations in BOM, even among modules of the same make and model can lead to reliability challenges.

14 SOLAR ENERGY↗
DOE OSTI2022

High‐Efficiency Solar Cells Grown on Spalled Germanium for Substrate Reuse without Polishing

Abstract Radical reduction of III–V device costs requires a multifaceted approach attacking both growth and substrate costs. Implementing device removal and substrate reuse provides an opportunity for substrate cost reduction. Controlled spalling allows removal of thin devices from the expensive substrate; however, the fracture‐based process currently generates surfaces with significant morphological changes compared to polished wafers. 49 single junction devices are fabricated across the spalled surface of full 50 mm germanium wafers without chemo‐mechanical polishing before epitaxial growth. Device defects are identified and related to morphological spalling defects—arrest lines, gull wings, and river lines—and their impact on cell performance using physical and functional characterization techniques. River line defects have the most consistent and detrimental effect on cell performance. Devices achieve a single junction efficiency above 23% and open‐circuit voltage of 1.01 V, demonstrating that spalled germanium does not need to be returned to a pristine, polished state to achieve high‐quality device performance.

14 SOLAR ENERGY↗
DOE OSTI2022

Differences in Printed Contacts Lead to Susceptibility of Silicon Cells to Series Resistance Degradation

Here, in this case study, we investigate a degradation mode occurring at the cell level in fielded multi-Si modules. The modules exhibit a mix of affected and unaffected cells. Affected cells show a progressive, series-resistance-related power degradation as shown via module- and cell-level IV curves, along with electroluminescence (EL) and PL imaging at the module, cell, and cell core sample scales. Scanning electron microscopy and energy-dispersive X-ray spectroscopy reveal a difference in the oxides in the silver paste used in screen printing of the gridline contacts. The paste in the affected cells is lead rich, whereas the paste in the unaffected cells is zinc rich. This suggests that the cells were screen printed with different silver paste compositions and possibly firing conditions, and that the different composition correlates with the susceptibility to degradation. Our results indicate degradation of the contact at the oxide-silver interface, causing a severe increase in series resistance across the cell that continues to progress over time.

14 SOLAR ENERGY↗