Search NASA⌕ Search

Engineering topics

Mann, M. J.

Publications and source records attributed to Mann, M. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Forward-swept wing configuration designed for high maneuverability by use of a transonic computational method

A transonic computational analysis method and a transonic design procedure have been used to design the wing and the canard of a forward-swept-wing fighter configuration for good transonic maneuver performance. A model of this configuration was tested in the Langley 16-Foot Transonic Tunnel. Oil-flow photographs were obtained to examine the wind flow patterns at Mach numbers from 0.60 to 0.90. The transonic theory gave a reasonably good estimate of the wing pressure distributions at transonic maneuver conditions. Comparison of the forward-swept-wing configuration with an equivalent aft-swept-wing-configuration showed that, at a Mach number of 0.90 and a lift coefficient of 0.9, the two configurations have the same trimmed drag. The forward-swept wing configuration was also found to have trimmed drag levels at transonic maneuver conditions which are comparable to those of the HiMAT (highly maneuverable aircraft technology) configuration and the X-29 forward-swept-wing research configuration. The configuration of this study was also tested with a forebody strake.

Mann, M. J.↗
NASA NTRS1985

A forward-swept wing configuration designed for high maneuverability by use of three-dimensional transonic theory

Supercritical technology has been applied to the design of a forward-swept-wing fighter configuration, and an assessment has been made of the relative performance of forward versus aft sweep. The wing and canard for this forward-swept wing configuration were designed for transonic maneuver by the use of a transonic computational analysis method and a transonic design procedure. The computational method calculates the transonic flow over a canard-wing-fuselage combination so that the strong transonic induced-flow effects of the canard on the wing are taken into account. A model of this configuration was constructed and was tested in the Langley 16-Foot Transonic Tunnel. The transonic theory gave a reasonably good estimate of the wing pressure distributions at transonic maneuver conditions. Comparison of this configuration with an equivalent aft-swept wing configuration showed that, at a Mach number of 0.9 and a lift coefficient of 0.9, the two configurations have essentially the same drag. This forward-swept wing configuration was also found to have very good maneuver performance relative to the Rockwell International HiMAT highly-maneuverable aircraft configuration.

Mann, M. J.↗
NASA NTRS1984

Low-speed investigation of effects of wing leading- and trailing-edge flap deflections and canard incidence on a fighter configuration equipped with a forward-swept wing

An advanced fighter configuration with a forward-swept wing of aspect ratio 3.28 is tested in the Langley 7 by 10 Foot High Speed Tunnel at a Mach number of 0.3. The wing has 29.5 degrees of forward sweep of the quarter chord line and is equipped with 15 percent chord leading edge and 30 percent chord trailing edge flaps. The canard is sweptback 45 degrees. Tests were made through a range of angle of attack from about -2 degrees to 22 degrees. Deflecting the flaps significantly improves the lift drag characteristics at the higher angles of attack. The canard is able to trim the configurations with different flap deflections over most of the range of angle of attack. The penalty in maximum lift coefficient due to trimming is about 0.10.

Gainer, T. G.↗
NASA NTRS1984

Aerodynamic design for improved manueverability by use of three-dimensional transonic theory

Improvements in transonic maneuver performance by the use of three-dimensional transonic theory and a transonic design procedure were examined. The FLO-27 code of Jameson and Caughey was used to design a new wing for a fighter configuration with lower drag at transonic maneuver conditions. The wing airfoil sections were altered to reduce the upper-surface shock strength by means of a design procedure which is based on the iterative application of the FLO-27 code. The plan form of the fighter configuration was fixed and had a leading edge sweep of 45 deg and an aspect ratio of 3.28. Wind-tunnel tests were conducted on this configuration at Mach numbers from 0.60 to 0.95 and angles of attack from -2 deg to 17 deg. The transonic maneuver performance of this configuration was evaluated by comparison with a wing designed by empirical methods and a wing designed primarily by two-dimensional transonic theory. The configuration designed by the use of FLO-27 had the same or lower drag than the empirical wing and, for some conditions, lower drag than the two-dimensional design. From some maneuver conditions, the drag of the two-dimensional design was somewhat lower.

Mann, M. J.↗
NASA NTRS1983

Aerodynamic design for improved maneuverability by the use of three-dimensional transonic theory

This study has examined the level of transonic maneuver performance that can be achieved by the use of three-dimensional transonic theory. The FLO-27 code of Jameson and Caughey (1977) was used to lower maneuver drag by the reduction of shock strength on the wing upper surface. A design procedure was used to provide a set of guidelines for the iterative application of FLO-27 during the wing design process. The fighter configuration utilized had a leading-edge sweep of 45 deg and an aspect ratio of 3.28. Tests were conducted at Mach numbers from 0.60 to 0.95 and angles of attack from -5 to 18 deg. The accurate prediction of wing shock systems required the inclusion of fuselage effects in the theory. The FLO-27 code gave a reasonable estimate of the experimental wing pressure distributions at transonic maneuver conditions in the region of the wing where the flow was attached. For Mach numbers between 0.60 and 0.95 and lift coefficients near 0.9, a wing designed by the use of FLO-27 showed substantially lower drag than an empirically developed, supercritical maneuver wing and a maneuver wing designed primarily by two-dimensional transonic theory. For some maneuver conditions, the drag of the two-dimensional design was somewhat lower.

Mann, M. J.↗
NASA NTRS1983

Experimental study of wing leading-edge devices for improved maneuver performance of a supercritical maneuvering fighter configuration

Wind tunnel tests were conducted to examine the use of wing leading-edge devices for improved subsonic and transonic maneuver performance. These devices were tested on a fighter configuration which utilized supercritical-wing technology. The configuration had a leading-edge sweep of 45 deg and an aspect ratio of 3.28. The tests were conducted at Mach numbers of 0.60 and 0.85 with angles of attack from -0.5 deg to 22 deg. At both Mach numbers, sharp leading-edge flaps produced vortices which greatly altered the flow pattern on the wing and resulted in substantial reductions in drag at high lift. Underwing or pylon-type vortex generators also reduced drag at high lift. The vortex generators worked better at a Mach number of 0.60. The vortex generators gave the best overall results with zero toe-in angle and when mounted on either the outboard part of the wing or at both an outboard location and halfway out the semispan. Both the flaps and the vortex generators had a minor effect on the pitching moment. Fluorescent minitufts were found to be useful for flow visualization at transonic maneuver conditions.

Mann, M. J.↗
NASA NTRS1982

Supercritical maneuvering fighter configuration. Wind-tunnel investigation at Mach numbers of 0.60 to 0.95

A wind tunnel investigation was conducted to study the application of supercritical technology to highly maneuverable combat aircraft. The configuration studied has a leading-edge sweep of 45 deg and an aspect ratio of 3.28. Two supercritical-wing shapes were tested at Mach numbers from 0.60 to 0.95 with angles of attack from -2 deg to 17 deg. On supercritical wing was designed to achieve a high level of transonic maneuver performance at a Mach number of 0.90; however, excessive flow separation developed on this wing at a Mach number of 0.85. A second supercritical wing was tested which had significantly reduced flow separation and improved drag characteristics at a Mach number of 0.85 and maintained the performance of the original wing at the higher Mach numbers. Leading-edge vortex generators did not improve the performance of the second wing; however, a sharp leading-edge flap produced sizable drag reductions at Mach numbers from 0.60 to 0.90.

Mann, M. J.↗
NASA NTRS1980

Wind-tunnel/flight correlation study of aerodynamic characteristics of a large flexible supersonic cruise airplane (XB-701) 2: Extrapolation of wind-tunnel data to full-scale conditions

The results of calculations necessary to extrapolate performance data on an XB-70-1 wind tunnel model to full scale at Mach numbers from 0.76 to 2.53 are presented. The extrapolation was part of a joint program to evaluate performance prediction techniques for large flexible supersonic airplanes similar to a supersonic transport. The extrapolation procedure included: interpolation of the wind tunnel data at the specific conditions of the flight test points; determination of the drag increments to be applied to the wind tunnel data, such as spillage drag, boundary layer trip drag, and skin friction increments; and estimates of the drag items not represented on the wind tunnel model, such as bypass doors, roughness, protuberances, and leakage drag. In addition, estimates of the effects of flexibility of the airplane were determined.

Peterson, J. B., Jr.↗
NASA NTRS1979

The design of supercritical wings by the use of three-dimensional transonic theory

A procedure was developed for the design of transonic wings by the iterative use of three dimensional, inviscid, transonic analysis methods. The procedure was based on simple principles of supersonic flow and provided the designer with a set of guidelines for the systematic alteration of wing profile shapes to achieve some desired pressure distribution. The method was generally applicable to wing design at conditions involving a large region of supercriterical flow. To illustrate the method, it was applied to the design of a wing for a supercritical maneuvering fighter that operates at high lift and transonic Mach number. The wing profiles were altered to produce a large region of supercritical flow which was terminated by a weak shock wave. The spanwise variation of drag of this wing and some principles for selecting the streamwise pressure distribution are also discussed.

Mann, M. J.↗
NASA NTRS1978

Theoretical estimation of the transonic aerodynamic characteristics of a supercritical-wing transport model with trailing-edge controls

A method for rapidly estimating the overall forces and moments at supercritical speeds, below drag divergence, of transport configurations with supercritical wings is presented. The method was also used for estimating the rolling moments due to the deflection of wing trailing-edge controls. This analysis was based on a vortex-lattice technique modified to approximate the effects of wing thickness and boundary-layer induced camber. Comparisons between the results of this method and experiment indicate reasonably good correlation of the lift, pitching moment, and rolling moment. The method required much less storage and run time to compute solutions over an angle-of-attack range than presently available transonic nonlinear methods require for a single angle-of-attack solution.

Luckring, J. M.↗
NASA NTRS1977

Transonic aerodynamic characteristics of a supercritical-wing transport model with trailing-edge controls

The effects of wing trailing-edge control surfaces on the static transonic aerodynamic characteristics of a transport configuration with a supercritical wing were studied. The configuration was tested with both an area-ruled fuselage and a cylindrical fuselage. The Mach number range was from 0.80 to 0.96 and the angle of attack range was from -1 deg to 12 deg. The Reynolds number was 1,580,000 based on the mean aerodynamic chord. Tabular data are presented.

Mann, M. J.↗
NASA NTRS1975

Low-speed upwash interference on a transport model in a rectangular slotted-wall wind tunnel

A study was made of the upwash interference caused by the wind tunnel walls at a Mach number of 0.20. The wind tunnel has slotted horizontal walls and solid vertical walls and the wind tunnel model is a wing-fuselage combination typical of a short take-off and landing (STOL) transport. Measurements were made of the model forces and angle of attack. The experimental results are compared to theoretical solutions for the upwash interference. This comparison enabled an indirect determination of one of the constants in the slotted wall boundary condition. The magnitude of the experimental upwash interference is also compared to the accuracy of the data. This comparison indicates that it is difficult to make definite conclusions based on the experimental data. Suggestions are made for future research which could provide a practical means of accurately determining the wall-interference velocities in wind tunnels with rigid slotted walls.

Mann, M. J.↗
NASA NTRS1974

Calculation of the twist distribution of wings designed for cruise at transonic speeds

The use of linear theory in calculating the twist distribution of a wing designed for cruise at supercritical speeds is justified on the basis of the transonic equivalence rule. A modified version of Multhopp's subsonic lifting-surface theory was used to calculate the twist distribution. The lifting-surface theory is compared with both slender wing theory and experimental results. A study was also made of the effect of wing sweep on the twist distribution required to maintain an elliptic span load at cruise conditions. The important parameters used in establishing this twist distribution are identified.

Mann, M. J.↗