Engineering topics

Mann, Michael

Publications and source records attributed to Mann, Michael.

10 records

DOE OSTI2023

Insights into Chemical Prelithiation of SiO x /Graphite Composite Anodes through Scanning Electron Microscope Imaging

Initial Coulombic efficiency (ICE) is critical for determining the energy density of lithium-ion batteries (LIBs) used for practical applications; however, it is typically disregarded in anode research. We used SiO x and graphite composite anodes for commercial lithium-ion batteries in our preliminary research to achieve a balance between ICE, capacity, and cycling life. ICE reached 88%; however, it needs further improvement for commercial applications. Prelithiation is a process that involves the introduction of extra lithium ions into LIBs during their manufacturing to enhance the overall performance of the LIBs. We applied a chemical prelithiation method on our SiO x /graphite composite anodes, which comprised 95 wt % of the active material mass loading on the electrode. The ICE increased from 88% to 98% using an aryllithium reagent impregnation method within 2 min of prelithiation. The anode’s specific capacity density, rate, and cycle performance also significantly improved. Scanning electron microscopy (SEM) imaging enhanced by an osmium tetroxide staining method indicated that the P-anode contained a stable solid electrolyte interface (SEI) layer after the prelithiation process and cycling electrochemical test. The P-anode’s stable charge differential peak over 500 cycles also showcases a robust artificial SEI layer that was generated by the prelithiation procedure. Here, this prelithiation process has significant potential for adoption in the LIB industry’s current electrode manufacturing process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Coal-derived graphene foam and micron-sized silicon composite anodes for lithium-ion batteries

Silicon-based materials demonstrate significant potential as lithium-ion batteries (LIBs) anode, but their expansion and degradation present engineering design challenges for commercial application. In this study, a porous three-dimensional (3D) graphene and micron-sized silicon composite anode (Si@G foam) was synthesized using humic acid (HA) derived from coal as a graphene precursor. In-situ formation of graphene structure through reducing HA was confirmed by Raman spectra. The reduced HA (rHA) shows similar electrical conductivity compared to the commercial conductive carbon. SEM images depict a 3D skeleton of coal-derived graphene, with silicon particles distributed on the 3D graphene foam's internal surface. The Si@G composite-anode displays a good reversible capacity of ~656 mAh/g at a current density of 50 mA/g, as well as a high-rate capability of ~433 mAh/g at a current density of 800 mA/g, and outstanding cycling stability –89.8% capacity retention after 300 cycles, which is significantly higher than that of other foam structures. During lithiation and de-lithiation, the graphene foam serves as a matrix of electrical conductors and a volume expansion support for silicon. This 3D graphene network will be beneficial for developing advanced silicon-based anodes for high-performance LIBs.

25 ENERGY STORAGE↗

DOE OSTI2022

Maximizing the Proppant Carrying and Viscoelastic Properties of the Bakken Hypersaline-Produced Water with High-Viscosity Friction Reducers for Sustainable Applications

Summary The development and production of unconventional reservoirs, such as the Bakken Formation, have become a resolved mystery for operators in North America since the arrival and advancement of horizontal drilling and hydraulic fracturing technologies. As a result, unconventional reservoir assets became the central focus of the oil and gas industry at the state, national, and global levels. The produced water from these activities in the Bakken Formation have high salt contents (110,000–350,000 ppm) total dissolve solids (TDS) and can pose significant challenges to the environment if not treated. Deep injection into disposal wells is the routine method used to get rid of the Bakken produced water. However, there have been some concerns that unrestrained injections, in addition to polluting the groundwater, could potentially lead to seismic activities either at the time of injection or in the near future. To diminish the environmental impacts that may be associated with induced seismicity, including the reduction of the costs of water acquisition, the produced water can be treated and reused in the hydraulic fracturing processes. Also, the treated water could be used for irrigation purposes, for power generation, and coal mining operations. The issues of waste water and residual oil high in TDS are challenges yet to be effectively addressed despite preceding research and studies on advancing produced water technologies. The goal of this study is to explore all applicable ways by which the produced water from the Bakken Formation can serve as a replacement base fluid for use with polymers like the high-viscosity friction reducers (HVFRs) to create hydraulic fracturing fluids that can be stable with reservoir conditions and also be able to minimize environmental impacts and cost of operations. Experimental investigations using the high-salinity produced water from the Bakken Formation with HVFRs were carried out. The studies included a base case that served as a bench mark for comparing the effectiveness of the other scenarios. The results indicate that the Bakken hyper-saline produced water can withstand effect of heavy metals, salinity, hardness and remain stable through different shear rates (66–330 s−1) when treated with higher dosages [4–8 gal/1,000 gal (gpt)] of HVFRs. Filtration and dilution were the only methods used on the Bakken Formation produced wate for this research

Engineering↗

DOE OSTI2022

Insights into the Effect of Heat Treatment and Carbon Coating on the Electrochemical Behaviors of SiO Anodes for Li-Ion Batteries

The use of SiO as an anode material has attracted significant interest due to its high capacity and long cycling life. Many promising approaches, including structural design and carbon coating at high temperatures, effectively improve its intrinsic low electrical conductivity and poor Coulombic efficiency. However, the “heat treatment process-composition and microstructure-electrochemical properties” relationship of the SiO anode is not fundamentally understood. Here the structure and composition evolution in amorphous SiO and graphene-coated SiO is investigated using different heat-treatment conditions. X-ray absorption near-edge structure techniques are also employed to analyze the surface and bulk composition change during the initial lithiation process, supplemented by physical or chemical characterization and electrochemical testing. Here results reveal the structural transition of SiO during heat treatment, from amorphous to disproportionated hierarchical structure, where the as-formed dielectric exterior SiO 2 shell and interior SiO 2 matrix severely polarizes electrodes, hindering the lithiation process. Carbon coating on SiO effectively restricts the growth of the SiO 2 shell and facilitates charge transfer, leading to improved electrochemical performance. A schematic model is proposed to reveal the relationship between the treatments, the resultant structural evolutions, and corresponding electrochemical behaviors.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Low-Cost Recyclable Oxygen Carrier and Novel Process for Chemical Looping Combustion

The University of North Dakota, through its Institute for Energy Studies and Energy & Environmental Research Center, partnered with Envergex LLC, Barr Engineering and Microbeam Technologies to develop a transformational enabling technology for advancement of Chemical Looping Combustion technology. Industrial support was provided by Carbontec Energy Corporation. The project targeted the two biggest challenges to chemical looping combustion: (1) High costs of oxygen carrier replacement/loss due to expensive manufacturing and high replacement rates from physical attrition and/or decrease in reactivity, and (2) Inherently slow fuel char conversion which represents the rate-limiting step for chemical looping combustion and results in very large equipment sizes, and overall lower carbon dioxide capture efficiency. The project activities were addressed in a series of seven tasks. Task 1 extended throughout the entire project and oversaw project management and execution. Task 2 and 3 focused on development and evaluation of the novel oxygen carrier. Task 4 to 7 focused on design of the novel reactor, testing with the novel oxygen carrier and a techno-economic assessment of the process. The list of tasks are: Task 1 – Project management and planning, Task 2 – Laboratory scale oxygen carrier manufacturing and assessment, Task 3 – Modeling and laboratory-scale evaluation of oxygen carrier performance with coal, Task 4 – 10-kilowatt thermal integrated system installation, Task 5 – Scaled-up oxygen carrier manufacturing, Task 6 – 10-kilowatt testing, and Task 7 – Process design and techno-economic analysis.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

In Situ Synthesis of Graphene-Coated Silicon Monoxide Anodes from Coa-Derived Humic Acid for High-Performance Lithium-Ion Batteries

Silicon monoxide (SiO) is attaining extensive interest amongst silicon-based materials due to its high capacity and long cycle life; however, its low intrinsic electrical conductivity and poor coulombic efficiency strictly limit its commercial applications. Here low-cost coal-derived humic acid (HA) is used as a feedstock to synthesize in-situ graphene-coated disproportionated SiO (D-SiO@G) anode with a facile method. HRTEM and XRD confirm the well-coated graphene layers on an SiO surface. Scanning Transmission X-ray Microscopy (STXM) and X-ray Absorption Near-Edge Structure (XANES) spectra analysis indicate that the graphene coating effectively hinders the side-reactions between the electrolyte and SiO particles . As a result, the D-SiO@G anode presents an initial discharge capacity of 1937.6 mAh g -1 at 0.1 A g -1 and an initial coulombic efficiency (ICE) of 78.2%. High reversible capacity (1023 mAh g -1 at 2.0 A g -1 ), excellent cycling performance ( 72.4% capacity retention after 500 cycles at 2.0 A g -1 ), and rate capability (774 mAh g -1 at 5 A g -1 ) results are substantial. Full coin cells assembled with LiFePO 4 electrodes and D-SiO@G electrodes display impressive rate performance. These results indicate a promising potential for practical use in high-performance lithium-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2020

Supercritical Treatment Technology for Water Purification (Annual Final Report)

This project continued the development of the Supercritical Water Extraction – Enhanced Targeted Recovery (SWEETR™) technology, a novel desalination process for treating hypersaline brines. The overall objective is to demonstrate the technical and economic feasibility of an innovative, energy efficient, and robust supercritical desalination technology to treat hypersaline solutions and separating saltwater into a pure water stream and valuable recovered solids, resulting in zero liquid discharge (ZLD). The proposed technology, focuses on innovative methods of applying supercritical water to treat highly concentrated brine solutions without incurring a high energy penalty. Integrating the technology with solar energy reduces the energy cost for the system. The results obtained during the proof-of-concept testing demonstrate that the SWEETR™ concept is technically feasible and that supercritical water treatment is a viable option with strong merit for treating high salinity waters. The strategic design of the system provides the opportunity to localize the supercritical zone, which helps reduce the overall energy cost associated with the desalination process. The process can be tuned to remove only the amount of salts required to make the treated water “fit for purpose”, providing further opportunities to minimize energy costs. The ability to destroy organic compounds associated with the water while simultaneously being able to desalinate makes SWEETR™ uniquely fitted for treating aqueous streams such as produced water from oil and gas extraction which contain small amounts of organics. Such mixed contaminant streams pose an extreme challenge for other treatment options. Future work will further develop the SWEETR™ technology to take it from the bench-scale to the pilot-scale, and ready the technology for commercial application.

04 OIL SHALES AND TAR SANDS↗

DOE OSTI2019

Reactive jet and cyclonic attrition analysis of ilmenite in chemical looping combustion systems

In chemical looping combustion (CLC), the chosen oxygen carrier’s (OC) reactivity maintenance and attrition propensity play key roles in determining its lifetime in such systems. Jet and cyclonic attrition are two main mechanisms of attrition in CLC systems, which typically use fluidized beds and cyclones. In contrast to standardized tests, that assess attrition characteristics under ambient and non-reacting conditions, a realistic evaluation must include the behavior under relevant high temperatures and cyclic oxidation-reduction. In this study, separate jet and cyclonic attrition test units were constructed to investigate the effects of temperature, fuel gas concentration and velocity on the performance of ilmenite, a natural ore-based OC in CLC. Testing showed that thermal and chemical effects were crucial to accurately determine the performance of ilmenite. For experiments conducted between 820°C and 970°C, the intermediate temperature of 895°C provided the best balance between high reactivity and material durability. Additionally, fuel gas concentration affected particle morphology evolution. Iron migration to the surface of the ilmenite particle was enhanced at higher fuel gas concentrations and resulted in reduced attrition rate, presumably due to sintering of the more highly reduced enriched iron phase on the particle surface. The laboratory jet and cyclonic attrition evaluation test units tested in this study can be used to investigate multiple parameters relevant for OC performance, including the degree of reduction, oxygen carrying capacity, attrition resistance, agglomeration, and optimum material operability conditions, as well as to extrapolate test data to determine OC replacement costs in a commercial CLC system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2019

Method for separation of coal conversion products from oxygen carriers

Complete fuel conversion represents an important, but unresolved, aspect in Chemical Looping Combustion (CLC). Different system design approaches are currently being investigated to maximize carbon conversion in the fuel reactor. To achieve greater than ninety percent conversion of the fuel in “fluid-bed” type reducers will require that CLC systems be equipped with additional process equipment to ensure that unburnt fuel leaving the reducer is minimized. This paper presents results obtained from a laboratory test system simulating a char stripper design comprising two components; one for separating large char particles, based on material density differentials, and another for removing small char particles from the oxygen carrier (OC) leaving the reducer, based on elutriation. A test unit was designed, built and operated to identify optimum conditions for separating OC material from unburnt solid fuel – char. The results obtained are necessary for designing a high temperature unit operated at temperatures expected within a CLC system.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2019

The relative influence of climate and housing development on current and projected future fire patterns and structure loss across three California landscapes

Climate and land use patterns are expected to change dramatically in the coming century, raising concern about their effects on wildfire patterns and subsequent impacts to human communities. The relative influence of climate versus land use on fires and their impacts, however, remains unclear, particularly given the substantial geographical variability in fire-prone places like California. Here, we developed a modeling framework to compare the importance of climatic and human variables for explaining fire patterns and structure loss for three diverse California landscapes, then projected future large fire and structure loss probability under two different climate (hot-dry or warm-wet) and two different land use (rural or urban residential growth) scenarios. The relative importance of climate and housing pattern varied across regions and according to fire size or whether the model was for large fires or structure loss. The differing strengths of these relationships, in addition to differences in the nature and magnitude of projected climate or land use change, dictated the extent to which large fires or structure loss were projected to change in the future. Despite this variability, housing and human infrastructure were consistently more responsible for explaining fire ignitions and structure loss probability, whereas climate, topography, and fuel variables were more important for explaining large fire patterns. For all study areas, most structure loss occurred in areas with low housing density (from 0.08 to 2.01 units/ha), and expansion of rural residential land use increased structure loss probability in the future. Regardless of future climate scenario, large fire probability was only projected to increase in the northern and interior parts of the state, whereas climate change had no projected impact on fire probability in southern California. Given the variation in fire-climate relationships and land use effects, policy and management decision-making should be customized for specific geographical regions.

54 ENVIRONMENTAL SCIENCES↗