Engineering topics
Manousiouthakis, Vasilios I.
Publications and source records attributed to Manousiouthakis, Vasilios I..
Field-Scale Testing of a High-Efficiency Membrane Reactor (MR)—Adsorptive Reactor (AR) Process for H2 Generation and Pre-Combustion CO2 Capture
The study objective was to field-validate the technical feasibility of a membrane- and adsorption-enhanced water gas shift reaction process employing a carbon molecular sieve membrane (CMSM)-based membrane reactor (MR) followed by an adsorptive reactor (AR) for pre-combustion CO2 capture. The project was carried out in two different phases. In Phase I, the field-scale experimental MR-AR system was designed and constructed, the membranes, and adsorbents were prepared, and the unit was tested with simulated syngas to validate functionality. In Phase II, the unit was installed at the test site, field-tested using real syngas, and a technoeconomic analysis (TEA) of the technology was completed. All project milestones were met. Specifically, (i) high-performance CMSMs were prepared meeting the target H2 permeance (>1 m3/(m2.hbar) and H2/CO selectivity of >80 at temperatures of up to 300 °C and pressures of up to 25 bar with a <10% performance decline over the testing period; (ii) pelletized adsorbents were prepared for use in relevant conditions (250 °C < T < 450 °C, pressures up to 25 bar) with a working capacity of >2.5 wt.% and an attrition rate of <0.2; (iii) TEA showed that the MR-AR technology met the CO2 capture goals of 95% CO2 purity at a cost of electricity (COE) 30% less than baseline approaches.
Bench-Scale Testing of a High Efficiency, Ultra-Compact Process for Pre-Combustion CO 2 Capture (Final Report)
The overarching objective of this bench-scale study is to field-validate the technical feasibility of a membrane- and adsorption-enhanced water gas shift (WGS) reaction process that employs a carbon molecular sieve (CMS) membrane reactor (MR) followed by an adsorption reactor (AR) for pre-combustion CO 2 capture while demonstrating progress towards achievement of the overall performance goals of CO 2 capture with 95% CO 2 purity at a cost of electricity (COE) of 30% less than the baseline capture approaches. The main goal of this bench-scale project is to advance the proposed MR-AR transformative CO 2 capture technology to a sufficient maturity level so that our present industrial partners (M&PT and Worley) can potentially adapt the technology for further small pilot-scale testing. The project began at TRL 4, as the system prototype had already been validated in the laboratory on simulated syngas (as part of project DE-FE0026423). The project ended at TRL 5, via scaling-up of the prototype system and testing it on actual syngas at a host site (CAER at the University of Kentucky (UKy)). The project was carried-out in two different phases: In Phase I (during BP1 of the project), the team designed, constructed, and assembled the bench-scale experimental MR-AR system, prepared the membranes, adsorbents, and catalysts, tested the bench-scale unit with simulated syngas to validate functionality, and prepared a preliminary TEA of the technology. In Phase II (during BP2 of the project), the team installed the unit at the test site at the UKy site and completed all utility connections and hookups, field-tested the novel MR-AR process in the bench-scale system using real syngas, collected and analyzed experimental data, and completed a detailed TEA of the technology. A key aim of the project was to identify and address the technical and process risks and to generate information to advance the technology to the next stage of development. All project milestones and success criteria were met. Specifically, the team: (i) designed, constructed and assembled a bench scale system that handled 1 – 5 scfm syngas and tested its functionality with simulated syngas; (ii) prepared high performance CMS membrane tubes (ID: 3.5 mm, OD: 5.7 mm, 30” long) that meet the target H 2 permeance ( > 1 m 3 /(m 2 .hr.bar) or (> 370.3 GPU)) and a target H 2 /CO selectivity >80 at the relevant temperature (up to 300oC) and pressure conditions (up to 25 bar) with a <10% decline in performance over each 250 hr. testing period (iii) procured commercial sour-shift catalyst in sufficient quantity and prepared up to 10 kg of pelletized adsorbent for use at relevant conditions (250oC 2.5wt.% and target sorbent attrition rate < 0.2; (iv) installed the bench-scale unit at the test site (UKy) and tested the MR-AR technology using real syngas for over 250 hr. for both static and flow experiments; (v) updated the TEA analysis based on bench-scale data and met CO 2 capture goals of 95% CO 2 purity at a cost of electricity 30% less than baseline capture approaches. The CMS membranes, HTC adsorbents and catalysts employed all exhibited very robust and stable performance during the long-term run (over a >250 hr live syngas run). Furthermore, the proposed MR-AR IGCC system achieved a LCOE with a N 2 sale price of $\$$ 30/ton, with N 2 compression (no N 2 compression) of 101.2 $\$$/MWh (95.3 $\$$/MWh), which represents a 29.8% (33.9%) LCOE reduction in the baseline IGCC with carbon capture of 144.2 $\$$/MWh. The proposed MR-AR IGCC delivers a CO 2 capture cost of 44.8 $\$$/tonne (39.9 $\$$/tonne) vs 98.1 $\$$/tonne of the baseline capture case and a net power production of 586 MWe (623 MWe) vs 556 MWe of the baseline capture case.
On multidomain multiscale modeling and simulation of a novel partial pressure and temperature swing adsorptive reactor ($\mathrm{PPTSAR}$) with application to the water gas shift reaction
Here in this work, a dynamic, multidomain, multiscale model of a novel Partial Pressure and Temperature Swing Adsorptive Reactor (PPTSAR) Process is developed and simulated for a Water Gas Shift Reaction (WGSR) application. The proposed model couples the reactor wall, catalyst/adsorbent pellet, and fluid mixture domains at their respective scales to comprehensively model mass, momentum, and energy transport phenomena occurring within each domain. The resulting model elucidates the PPTSAR’s start-up, transient, and long-term, periodic, dynamic behavior, during both adsorption/reaction and desorption operating modes. In the WGSR application considered, the use of two PPTSARs is shown to allow continuous operation that delivers CO conversion greater than 95% with simultaneous complete CO 2 capture.
A reactive separation process for pre-combustion CO 2 capture employing oxygen-blown coal gasifier off-gas
In this paper, we present an experimental study of a reactive separation system, consisting of a membrane reactor (MR) and an adsorptive reactor (AR) operating in tandem, with the MR’s reject stream serving as the AR’s feed. We investigates the feasibility of applying this MR-AR system for high-purity H 2 production and simultaneous CO 2 capture via the water gas shift (WGS) reaction in the context of Integrated Gas Combined Cycle (IGCC) power generation employing oxygen-blown gasifier syngas from biomass and coal. We previously studied this MR-AR system for the IGCC process employing air-blown gasifier syngas, for which it demonstrated good performance, attaining high conversion exceeding equilibrium, producing ultra-pure H 2 for power generation, and a CO 2 stream ready for sequestration. In this study, we focus on oxygen-blown gasifier off-gas that contains no N 2 , with composition distinctly different from the air-blown gasifier syngas which has a large N 2 content. We employ a carbon molecular sieve membrane (CMSM), a commercial sour-shift WGS catalyst, and a hydrotalcite (HTC) adsorbent. We carried out experiments to determine membrane performance and to identify promising operating conditions in an IGCC-relevant environment. The CMSM proved robust during a long-term (~344 hr run) experimental run under high temperature and pressure maintaining a high He/N 2 selectivity (~170). Multi-cycle runs were carried out during which the MR-AR system displayed superior performance to that of a PBR, by producing a high purity H 2 product directly usable in power generation. Therefore, the findings from this study demonstrate the ability of the MR-AR system to operate stably for a broad range of gasifier off-gas compositions, and indicate its potential for integration into IGCC plants for power generation with CO 2 capture.
A carbon molecular sieve membrane-based reactive separation process for pre-combustion CO 2 capture
In this study, we discuss a hybrid system combining a membrane reactor (MR) and an adsorptive reactor (AR), with the MR's reject stream serving as the AR's feed. We apply this system for the water gas shift (WGS) reaction for H 2 generation and simultaneous CO 2 capture in the context of the Integrated Gas Combined Cycle (IGCC) process for power generation from coal and biomass. This MR-AR system attains a high conversion exceeding equilibrium, produces a pure H 2 product for power generation, and delivers a high-pressure CO 2 stream ready for sequestration. Specifically, in our study we use carbon molecular sieve membranes (CMSMs) and a commercial sour-shift WGS catalyst. Lab experiments were carried-out to determine the membrane characteristics, and the MR performance under IGCC-relevant conditions, i.e., for temperatures up to 250 °C and pressures up to 25 bar, employing a model coal gasifier syngas. The CMSM and the catalyst have displayed robust and stable performance during a long-term run (~750 h of syngas exposure). We evaluated the MR-AR system in multi-cycle runs and it has demonstrated superior performance to that of a conventional packed-bed reactor, producing a high-purity H 2 product directly useable in a turbine for power generation. We conclude from the study, that the CMSM-based MR-AR system is a good candidate technology for environmentally-benign power generation. We are currently constructing a pilot-scale system for field demonstration of the technology.
Multi-scale model based design of membrane reactor/separator processes for intensified hydrogen production through the water gas shift reaction
This paper aims to first quantify the impact of various diffusion models (Maxwell-Stefan, Wilke, Dusty-Gas) on the predictions of a multi-scale membrane reactor/separator mathematical model, and to then demonstrate this model's use for the design and process intensification of membrane reactor/separator systems for hydrogen production. This multi-scale model captures velocity, temperature and species' concentration profiles along the catalyst pellet's radial direction, and along the reactor's axial direction, by solving the momentum, energy, and species transport equations, accounting for convection, conduction, reaction, and diffusion mechanisms. In the first part of work, the effect of pellet-scale design parameters (mean pore diameter, volumetric porosity, tortuosity factor, etc.) and various species' flux models on the model predictions is studied. In the second part, the study focuses on the comparison, in terms of their process intensification characteristics, of various hydrogen production processes. These include a conventional high-temperature shift reactor (HTSR)/low-temperature shift reactor (LTSR) sequence, a novel HTSR/membrane separator (MS)/LTSR/MS sequence, and a process that involves low-temperature shift membrane reactors-LTSMR in a series.