Engineering topics
Mansley, Zachary R.
Publications and source records attributed to Mansley, Zachary R..
Manganese-rich high entropy oxides for lithium-ion batteries:materials design approaches to address voltage fade
Lithium- and manganese-rich oxides are of interest as lithium-ion battery cathode materials as Mn is earth abundant, low cost, and can deliver high capacity. Herein, a high entropy strategy was used to prepare Mn rich high entropy oxide (HEO) materials by including four additional metals (Ni, Co, Fe and Al) in the compositions using a mild co-precipitation method. Two HEOs (Li x Ni 0.1 Mn 0.6 Co 0.1 Al 0.1 Fe 0.1 O y , where x = 1.5 for HEO-L and x = 0.5 for HEO-H) with layered and spinel-layered hybrid structures were investigated where the morphology, elemental composition, structure, atomic level phase distribution, and electrochemistry were determined. The HEO-L samples involve a Li 2 TMO 3 layered structure with ~39% stacking faults. HEO-H is a hybrid structure comprised of 80 wt% spinel and 20 wt% LiMO 2 layered structure. The high entropy manganese-rich HEO-L showed higher capacity and 93% retention of the average voltage after 100 cycles while HEO-H showed higher capacity retention and near 100% average voltage retention. Finally, operando X-ray absorption spectroscopy revealed that the Ni, Co, and Mn are redox active in both materials while the Fe center remains at the Fe 3+ oxidation state throughout cycling, where the changes in the oxidation states for both materials during discharge were consistent with the delivered electrochemical capacity rationalizing the observed electrochemistry.
Identifying point defects and ordering in the high-entropy layered oxide Li 1.5 MO 3-δ (M=Mn, Al, Fe, Co, Ni) for energy storage applications
High-entropy layered oxides (HELOs) represent a very promising class of next-generation battery cathodes, combining the well-studied properties of layered cathode materials such as LiCoO 2 with the chemical tunability and stability of high-entropy materials. HELO materials often form particles with complex defects and domain structures, complicating accurate characterization of structure and cation mixing. Understanding disorder and order in HELO materials is necessary for understanding their performance and utility as cathodes. Here we demonstrate the characterization of the HELO Li 1.5 MO 3-δ (M = Mn, Al, Fe, Co, Ni), wherein X-ray powder diffraction, transmission electron microscopy imaging, and electron diffraction patterns are analyzed to reveal the presence of ordering in the HELO, with imaging and diffraction simulation employed to compare experimental results to atomic modeling. Finally, without rigorous characterization at the atomic scale, important features such as defect ordering can be easily overlooked and therefore remain unconsidered when interpreting experimental results.
Defect-Driven Configurational Entropy in the High-Entropy Oxide Li 1.5 MO 3-δ
Layered lithiated oxides are promising materials for next generation Li-ion battery cathode materials; however, instability during cycling results in poor performance over time compared to the high capacities theoretically possible with these materials. Here, in this paper, we report the characterizations of a Li 1.47 Mn 0.57 Al 0.13 Fe 0.095 Co 0.105 Ni 0.095 O 2.49 high-entropy layered oxide (HELO) with the Li 2 MO 3 structure where M = Mn, Al, Fe, Co, and Ni. Using electron microscopy and X-ray spectroscopy, we identify a homogeneous Li 2 MO 3 structure stabilized by the entropic contribution of oxygen vacancies. This defect-driven entropy would not be attainable in the LiMO 2 structure sometimes observed in similar materials as a secondary phase owing to the presence of fewer O sites and a 3+ oxidation state for the metal site; instead, a Li 2-γ MO 3-δ is produced. Beyond Li 2 MO 3 , this defect-driven entropy approach to stabilizing novel compositions and phases can be applied to a wide array of future cathode materials including spinel and rock salt structures.
Mechanism of Chalcophanite Nucleation in Zinc Hydroxide Sulfate Cathodes in Aqueous Zinc Batteries
Aqueous Zn-ion batteries with MnO 2 -based cathodes have seen significant attention owing to their high theoretical capacities, safety, and low cost; however, much debate remains regarding the reaction mechanism that dominates energy storage. In this work, we report our electron microscopy study of cathodes containing zinc hydroxide sulfate (Zn 4 SO 4 (OH) 6 ·xH 2 O, ZHS) together with carbon nanotubes cycled in electrolytes containing ZnSO 4 with varied amounts of MnSO 4 incorporated. The primary Mn-containing phase is formed in situ in the cathode during cycling, where a dissolution-deposition reaction is identified between ZHS and chalcophanite (ZnMn 3 O 7 ·3H 2 O). Mechanistic details of this reaction, in which the chalcophanite nucleates then separates from the ZHS flakes as the ZHS dissolves while acting as the primary Zn source for the reaction, are revealed using surface sensitive methods. Importantly, these findings indicate the reaction is local to the ZHS flakes, providing new insight toward the importance of ZHS and the cathode microstructure.
Iridium Incorporation into MnO 2 for an Enhanced Electrocatalytic Oxygen Evolution Reaction
Here, we have investigated the structure and activity of electrocatalysts for the oxygen evolution reaction (OER) that had low loadings of Ir incorporated into the 2D layered MnO 2 , (birnessite, nominally δ-MnO 2 ) and the 3D MnO 2 (pyrolusite, β-MnO 2 ). The Ir-incorporated β-MnO 2 (Ir/β-MnO 2 ) electrocatalysts were prepared for the first time via a thermally induced phase transition of δ-MnO 2 containing 16-22 wt% Ir. This phase transition of δ-MnO 2 to β-MnO 2 was facilitated by the presence of Ir in the structure, as both Ir in IrO 2 and Mn in β-MnO 2 could adopt a thermodynamically favored rutile structure. Extended X-ray absorption fine structure (EXAFS) of Ir/β-MnO 2 showed that the catalyst consisted of Ir substituted into the crystalline β-MnO 2 lattice. 22 wt% Ir/β-MnO 2 (60 μg Ir cm $\ ^{-2}_{geo}$) exhibited an OER overpotential (η) of 337 mV, lower than the η for commercial IrO 2 . This η was constant for 6 h, at 10 mA cm $\ ^{-2}_{geo}$ in 0.5 M H 2 SO 4 . EXAFS, high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and X-ray absorption near edge structure (XANES) showed that 22 wt% Ir/β-MnO 2 had a strained structure containing ~41% Mn 3+ , an OER active species, along with a modified Ir bond covalency consisting of both Ir-O-Ir and Ir-O-Mn.
Simultaneous Elucidation of Solid and Solution Manganese Environments via Multiphase Operando Extended X-ray Absorption Fine Structure Spectroscopy in Aqueous Zn/MnO 2 Batteries
Not Available
Identifying Support Effects in Au-Catalyzed CO Oxidation
Some catalytic oxide supports are more equal than others, with numerous variable properties ranging from crystal symmetry to surface chemistry and electronic structure. As a consequence, it is often very difficult to determine which of these act as the driver of performance changes observed in catalysis. In this work, we hold many of these variable properties constant with structurally similar LnScO 3 (Ln = La, Sm, and Nd) nanoparticle supports with cuboidal shapes and a common Sc-rich surface termination. Using CO oxidation over supported Au nanoparticles as a probe reaction, we observe higher activation energy and a slower rate using NdScO 3 as the support material. This change is found to correlate to the strength of CO 2 binding to the support surface, identified by temperature-programmed desorption measurements. Furthermore, the change is due to differences in the 4f electrons of the lanthanide cations, the cations’ Lewis acidity, and the inductive effect they impose.
Modified Winterbottom Construction Including Boundaries
There has been extensive work on the equilibrium shape of isolated nanoparticles with internal boundaries, and also single crystals on substrates. Surprisingly, almost shockingly, there has been very little work on the equilibrium shape of particles with internal boundaries on substrates. Here in this paper, the general solution is given for the configuration of particles which contain twin and other grain boundaries on a flat substrate, which can be applied to any polycrystalline or multiphase nanoparticle configuration. The solution is based upon combining the established modified-Wulff construction that has been extensively validated for twinned particles with the Winterbottom construction for single particles on a substrate. The solution is illustrated for the specific case of five-fold multiply twinned particles. Good agreement is observed between both existing experimental data in the literature as well as some experimental data included within this work.
Structure of the (110) Ln ScO 3 ( Ln =Gd,Tb,Dy) surfaces
The surface reconstruction on the (110) surface of LnScO 3 (Ln=Gd,Tb,Dy) has been investigated using x-ray photoelectron spectroscopy, atomic force microscopy, and transmission electron diffraction coupled with higher-level density-functional theory methods. The experimental techniques generate constraints on the surface chemistry and structure that are used to inform the theoretical comparison of a number of potential surface structures. The resulting structure is then compared to experimental aberration-corrected transmission electron microscopy results using multislice simulation. The surfaces of both single-crystalline substrates and hydrosauna synthesized nanoparticles exhibit a Sc-rich double layer with a Sc 3 O 4 termination.
Controlled Two-Step Formation of Faceted Perovskite Rare-Earth Scandate Nanoparticles
A general approach to the formation of well-faceted nanoparticles is discussed and successfully applied to the production of several rare-earth scandates. Two steps were used, with higher temperatures first to nucleate the perovskite phase, followed by lower temperatures to smooth the particle surfaces. Exploiting these two different regimes led to smaller nanoparticles with more faceting. This general approach may be tailored to other material systems as a step towards producing shape-controlled nanoparticles for a desired application.
The Vacancy-Induced Electronic Structure of the SrTiO 3-δ Surface
The emergence of a 2D electron gas (2DEG) on the (001) surface of oxygen-deficient strontium titanate (SrTiO 3-δ ) is investigated. Using in situ soft X-ray spectroscopy and effective mass modeling, a series of quantitative band diagrams are developed to describe the evolution of near-surface and bulk carrier concentrations, downward band bending, and Fermi level along a lateral gradient of oxygen vacancies formed on SrTiO 3-δ by direct-current resistive heating under ultrahigh vacuum conditions. Electrons are accumulated over a 3 nm region near the surface, confined within a potential well with saturated 300 meV downward band bending. The relation between Fermi levels and carrier concentrations near the surface suggests the density of states near the surface is much lower than the bulk density of states, which is consistent with the quantum-confined subbands of a 2DEG. The quantitative relationship between the surface and bulk electronic structures developed in this work provides a guide for precise engineering of the oxygen-vacancy-induced 2DEG in SrTiO 3 .
Synthesis of Gadolinium Scandate from a Hydroxide Hydrogel
In this paper, gadolinium scandate (GdScO 3 ) has been synthesized at 300 °C through the decomposition of a mixed cation hydroxide hydrogel in a humid environment. Increasing the reaction temperature produced larger particles that better adopted the Wulff shape. A lack of water vapor during the synthesis caused the solid network of the hydrogel to collapse upon heating so an amorphous xerogel was produced. Water vapor in the system imbibed the hydrogel and allowed for greater diffusion of the atomic species to allow for crystallization into the perovskite phase at temperatures lower than typical sol–gel processes. Finally, temperatures less than 300 °C, or an excess of water vapor, promoted the formation of Gd(OH) 3 and ScOOH in addition to or in lieu of GdScO 3 .