Search NASA⌕ Search

Engineering topics

Manthiram, Arumugam

Publications and source records attributed to Manthiram, Arumugam.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A New Class of Oxyhalide Solid Electrolytes NaNbCl 6‐2x O x for Solid‐state Sodium Batteries

Abstract Sodium‐based batteries are gaining momentum due to the abundance and lower cost of sodium compared to lithium. Solid‐state sodium batteries can also provide further safety advantages. However, sodium‐based solid‐state electrolytes (SSEs) that meet all the rigorous requirements, such as high ionic conductivity, oxidative stability with the cathode, and ease of processability, are lacking. We present here a new class of sodium‐based oxyhalide electrolytes NaNbCl 6‐2x O x with a facile mechanochemical synthesis. The oxyhalide NaNbCl 4 O exhibits close to two orders of magnitude higher ambient‐temperature sodium‐ion conductivity (1.03×10 −4 S cm −1 ) compared to the halide counterpart NaNbCl 6 (3×10 −6 S cm −1 ). Structural motifs unique to the oxygen content in NaNbCl 6‐2x O x are identified with 23 Na and 93 Nb magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy and x‐ray diffraction (XRD). Solid‐state sodium batteries assembled with NaNbCl 4 O electrolyte and the cobalt‐ and nickel‐free layered Na 0.70 Fe 0.3 Mn 0.65 Al 0.05 O 2 cathode exhibit a maximum discharge capacity of 155 mAh g −1 with good cycle life at ambient temperature.

Kmiec, Steven↗
DOE OSTI2024

A New Class of Oxyhalide Solid Electrolytes NaNbCl 6‐2x O x for Solid‐state Sodium Batteries

Abstract Sodium‐based batteries are gaining momentum due to the abundance and lower cost of sodium compared to lithium. Solid‐state sodium batteries can also provide further safety advantages. However, sodium‐based solid‐state electrolytes (SSEs) that meet all the rigorous requirements, such as high ionic conductivity, oxidative stability with the cathode, and ease of processability, are lacking. We present here a new class of sodium‐based oxyhalide electrolytes NaNbCl 6‐2x O x with a facile mechanochemical synthesis. The oxyhalide NaNbCl 4 O exhibits close to two orders of magnitude higher ambient‐temperature sodium‐ion conductivity (1.03×10 −4 S cm −1 ) compared to the halide counterpart NaNbCl 6 (3×10 −6 S cm −1 ). Structural motifs unique to the oxygen content in NaNbCl 6‐2x O x are identified with 23 Na and 93 Nb magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy and x‐ray diffraction (XRD). Solid‐state sodium batteries assembled with NaNbCl 4 O electrolyte and the cobalt‐ and nickel‐free layered Na 0.70 Fe 0.3 Mn 0.65 Al 0.05 O 2 cathode exhibit a maximum discharge capacity of 155 mAh g −1 with good cycle life at ambient temperature.

Kmiec, Steven↗
DOE OSTI2024

Cost‐Effective Layered Oxide – Olivine Blend Cathodes for High‐Rate Pulse Power Lithium‐Ion Batteries

Abstract Sustainability and supply‐chain concerns require lithium‐ion batteries (LIBs) free from critical minerals, such as nickel and cobalt. While recent advances provide encouraging signs that cobalt can be removed, the question remains how much Ni can be removed from Co‐free layered oxide cathodes before sacrificing critical performance metrics. This study highlights the effect of reducing Ni by benchmarking several Co‐free cathodes with decreasing Ni content. Keeping the energy density the same by increasing the charge voltage, cathodes below 80% Ni content exhibit worsened capacity fade due to increasing oxygen release and electrolyte decomposition. Charge transfer and diffusion kinetics are also hindered with increasing Mn content and exacerbated by resistive surface phases formed at high voltages, rendering lower‐Ni, Co‐free cathodes less competitive than high‐Ni cathodes for high energy and power applications. It is demonstrated blending layered oxide with olivine as an effective alternative to deliver energy density and cycling stability comparable to lower‐Ni cathodes with moderate charging voltages. Blending with 30 wt% olivine LiMn 0.5 Fe 0.5 PO 4 (LMFP) virtually eliminates the diffusion limitation of layered oxides at low state‐of‐charge, with enhanced pulse power characteristics rivaling the high‐Ni counterparts. Cathode blending can further reduce the overall Ni content and cost without the performance limitations of lower‐Ni, Co‐free cathodes.

Lee, Steven↗
DOE OSTI2024

Deconstructing the High Voltage Degradation Mechanisms in Na 2/3 Ni 1/3 Mn 2/3 O 2 with Single Crystals and Advanced Electrolyte

Abstract Sodium layered oxide cathodes can uniquely benefit from the existing lithium‐ion battery industry as sodium‐ion batteries gain traction as a potential low‐cost, drop‐in replacement. However, achieving relevant energy density with a suitable cycle life remains a challenge for sodium layered oxides. At high operating potentials, several competing degradation mechanisms prevent P2‐type Na 2/3 Ni 1/3 Mn 2/3 O 2 (≈550 Wh kg −1 ) from achieving meaningful cycle life—with bulk structural instability and surface reactivity being the primary retractors. Herein, the issue of particle cracking is addressed through detailed synthesis methods of “single‐crystal” materials. By comparison to a polycrystalline baseline, the single‐crystal materials quantify the capacity loss due to isolation of active material caused by intergranular particle cracking. The single crystal materials are then employed in cells with an advanced, “localized saturated electrolyte” (LSE) to demonstrate the magnitude of capacity loss due to electrolyte decomposition at the cathode surface. Mitigation of the surface reactivity through the LSE electrolyte effectively demonstrates the elevated importance of surface reactivity at high voltages despite the onset of egregious particle cracking. This work aims to guide future research into understanding molten‐salt assisted syntheses and advance the debate on surface versus bulk degradation.

Darga, Joe↗
DOE OSTI2024

Formation and Detriments of Residual Alkaline Compounds on High-Nickel Layered Oxide Cathodes

High-nickel layered oxides LiNi x M 1-x O 2 (x ≥ 0.9) have emerged as promising cathode materials for automotive batteries due to their high energy density and lower cost. However, the formation and accumulation of surface alkaline compounds during storage hinder their mass production and commercialization. Here, in this study, a validated chemical method is employed to deconvolute and quantify the evolution of each residual lithium compound in four representative cathodes during ambient-air storage, viz., LiNiO 2 (LNO), LiNi 0.95 Co 0.05 O 2 (NC), LiNi 0.95 Mn 0.05 O 2 (NM), and LiNi 0.95 Al 0.05 O 2 (NA). Furthermore, the activation energy of the reaction between water and the cathode is determined by measuring the leached LiOH concentration at various temperatures. While residual lithium and time-of-flight secondary-ion mass spectrometry measurements collectively reveal that the air stability overall follows the trend of NM > NA ≈ NC > LNO, the aged NM exhibits the highest charge-transfer resistance and the worst electrochemical performance among the cathodes. In situ, X-ray diffraction and scanning transmission electron microscopy unveil that the aged NM is plagued by a large area of resistive spinel-like M 3–x Li x O 4 phases, leading to aggravated particle reaction heterogeneity. Finally, a one-step recalcination method is demonstrated effective in fully restoring the degraded cathodes. This work provides insights into overcoming air sensitivity issues of high-Ni cathodes.

(S)TEM↗
DOE OSTI2024

A Class of Sodium Transition-Metal Sulfide Cathodes With Anion Redox

Sodium-ion batteries (SIBs) are entering commercial relevance as a sustainable and low-cost alternative to lithium-ion batteries. Improving the energy density of SIBs is critical to enable their widespread adoption. Here, in this work, a new class of cathode materials Na 6 M S 4 ( M = Co, Mn, Fe, and Zn) that exhibit high charge-storage capacity is reported. Using Na 6 CoS 4 as a prototypical example, a six-electron conversion reaction dominated by anion redox is observed, confirmed through various electrochemical and spectroscopic techniques. After the initial cycle, Na 6 CoS 4 delivers a high capacity of 392 mA h g -1 with a long lifespan of over 500 cycles. The reaction involves, initially, the transformation of crystalline Na 6 CoS 4 to a nearly amorphous structure consisting of mainly CoS and sulfur nanoparticles, which then reversibly cycles between nearly amorphous a-CoS/S and a-Na 6 CoS 4 . Such anion-redox-driven conversion-type cathodes hold the potential to enable energy-dense, stable SIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Phloroglucinol–2,6‐Diaminoanthraquinone as a Durable Redox Mediator for Enhancing Conversion Reaction Kinetics in Lithium‐Sulfur Batteries

Abstract Lithium‐sulfur batteries, despite being a promising solution for next‐generation secondary batteries, require substantial efforts to overcome the challenges of sluggish sulfur redox kinetics, polysulfides shuttling, and Li metal instability before achieving practical viability. Conventional strategies that utilize metal catalysts or soluble redox mediators (RMs) are limited by either impractical producing processes or unsatisfactory service life. Herein, an electrochemically active organic material, phloroglucinol – 2,6‐diaminoanthraquinone (PG‐DAAQ) is synthesized through a green and facile polymerization process to better resolve these issues. Serving as an RM at the cathode, PG‐DAAQ exhibits enduring redox activity within the sulfur operating potential window, leading to enhanced redox kinetics and sulfur utilization. Remarkably, even without any metal elements, PG‐DAAQ exhibits an excellent affinity to polysulfides, thereby suppressing the shuttling and facilitating the formation of a more favorable solid‐electrolyte interface to stabilize Li deposition at the anode. As a result, Li‐S cells employing PG‐DAAQ show significantly enhanced cycling and rate performances than the control cells. Even with a low electrolyte‐to‐sulfur ratio of 6, pouch cells with PG‐DAAQ deliver a reversible discharge capacity of 821 mA h g −1 after 100 cycles at a C/10 rate.

Lai, Tianxing↗
DOE OSTI2024

Mitigating Sodium Ordering for Enhanced Solid Solution Behavior in Layered NaNiO 2 Cathodes

Abstract The O‐type layered nickel oxides suffer from undesired cooperative Jahn–Teller distortion stemming from Ni 3+ ions and undergo multiple biphasic structural transformations during the insertion/extraction of large Na + ions, posing a significant challenge to stabilize the structural integrity. We present here a systematic investigation of the impact of substituting 5 % divalent (Mg 2+ ) or trivalent (Al 3+ or Co 3+ ) ions for Ni 3+ to alleviate Na + ion ordering and perturb the Jahn–Teller effect to enhance structural stability. We gauge a fundamental understanding of the Mg−O and Na−O or Mg−O−Na bonding interactions, noting that the ionicity of the Mg−O bond deshields the electronic cloud of oxygen from Na + ions. Furthermore, calculations of the Van Vleck distortion modes reveal a relaxation of NiO 6 octahedra from Jahn–Teller distortion and a reduced electron density at the interlayer with Mg 2+ substitution. Long‐range ( operando X‐ray diffraction) and short‐range (magic angle spinning nuclear magnetic resonance) structural analyses provide insights into reduced ordering, allowing a stable continuous solid solution. Overall, Mg‐substitution results in a high‐capacity retention of ~96 % even after 100 cycles, showcasing the potential of this strategy for overcoming the structural instabilities and enhancing the performance of sodium‐ion batteries.

Sada, Krishnakanth↗
NASA NTRS2010

Surface and bulk modified high capacity layered oxide cathodes with low irreversible capacity loss

The present invention includes compositions, surface and bulk modifications, and methods of making of (1-x)Li[Li.sub.1/3Mn.sub.2/3]O.sub.2.xLi[Mn.sub.0.5-yNi.sub.0.5-yCo.sub.2- y]O.sub.2 cathode materials having an O3 crystal structure with a x value between 0 and 1 and y value between 0 and 0.5, reducing the irreversible capacity loss in the first cycle by surface modification with oxides and bulk modification with cationic and anionic substitutions, and increasing the reversible capacity to close to the theoretical value of insertion/extraction of one lithium per transition metal ion (250-300 mAh/g).

Manthiram, Arumugam↗