Search NASA⌕ Search

Engineering topics

Maqueda, R J

Publications and source records attributed to Maqueda, R J.

Gas Puff Imaging Diagnostics of Edge Plasma Turbulence in Magnetic Fusion Devices

Gas puff imaging (GPI) is a diagnostic of plasma turbulence which usesa puff of neutral gas at the plasma edge to increase the local visiblelight emission for improved space-time resolution of plasmafluctuations. This paper reviews gas puff imaging diagnostics of edgeplasma turbulence in magnetic fusion research, with a focus on theinstrumentation, diagnostic cross-checks, and interpretationissues. The gas puff imaging hardware, optics, and detectors aredescribed for about 10 GPI systems implemented over the past ~15years. Comparison of GPI results with other edge turbulence diagnosticresults are described and many common features are observed. Severalissues in the interpretation of GPI measurements are discussed, andpotential improvements in hardware and modeling are suggested.

Gas puff imaging↗

Large Area Divertor Temperature Measurements Using A High-speed Camera With Near-infrared FiIters in NSTX

Fast cameras already installed on the National Spherical Torus Experiment (NSTX) have be equipped with near-infrared (NIR) filters in order to measure the surface temperature in the lower divertor region. Such a system provides a unique combination of high speed (> 50 kHz) and wide fi eld-of-view (> 50% of the divertor). Benchtop calibrations demonstrated the system's ability to measure thermal emission down to 330 oC. There is also, however, signi cant plasma light background in NSTX. Without improvements in background reduction, the current system is incapable of measuring signals below the background equivalent temperature (600 - 700 oC). Thermal signatures have been detected in cases of extreme divertor heating. It is observed that the divertor can reach temperatures around 800 oC when high harmonic fast wave (HHFW) heating is used. These temperature profiles were fi t using a simple heat diffusion code, providing a measurement of the heat flux to the divertor. Comparisons to other infrared thermography systems on NSTX are made.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Comparison of scrape-off layer turbulence simulations with experiments using a synthetic gas puff imaging diagnostic

A synthetic gas puff imaging (GPI) diagnostic has been added to the scrape-off layer turbulence (SOLT) simulation code, enabling comparisons with GPI data from the National Spherical Torus Experiment (NSTX) [M. Ono et al., Nucl. Fusion 40, 557 (2000)]. The edge and scrape-off layer are modeled in the radial and poloidal (bidirectional) dimensions of the outboard midplane region of NSTX. A low-confinement mode discharge is simulated by choosing reference parameters, including radial density and temperature profiles, to be consistent with those of the shot (no. 112825). NSTX and simulation GPI data are submitted to identical analyses. It is demonstrated that the level of turbulent fluctuations in the simulation may be adjusted to give synthetic GPI radial intensity profiles similar to those of the experiment; for a ''best-case'' simulation, SOLT and NSTX probability distribution functions of blob radial locations, widths, and GPI image velocities are compared. For the simulation, synthetic GPI image velocity and fluid convection (ExB) velocity are compared and contrasted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Flow and shear behavior in the edge and scrape-off layer of L-mode plasmas in National Spherical Torus Experiment

Fluctuations in the edge and scrape-off layer (SOL) of L-mode plasmas in the National Spherical Torus Experiment [Kaye et al., Phys. Plasmas 8, 1977 (2001)] as observed by the gas puff imaging (GPI) diagnostic are studied. Calculation of local, time resolved velocity maps using the hybrid optical flow and pattern matching velocimetry code enables analysis of turbulent flow and shear behavior. Periodic reversals in the direction of the poloidal flow near the separatrix are observed. Also, poloidal velocities and their radial shearing rate are found to be well correlated with the fraction of D{sub {alpha}} light contained in the SOL, which acts as a measure of turbulent bursts. The spectra of GPI intensity and poloidal velocity both have a strong feature near 3 kHz, which appears to correspond with turbulent bursts. This mode exhibits a poloidal structure with poloidal wavenumber of 7.7 m{sup -1} for GPI intensity and 3.4 m{sup -1} for poloidal velocity, and the poloidal velocity fluctuations near 3 kHz remain coherent over length scales in excess of the turbulent scales. Furthermore, recent SOL turbulence simulations find a parameter regime that exhibits periodic bursty transport and shares many qualitative similarities with the experimental data. Strong correlations between the shearing rate and the turbulent bursts are observed for time periods of {approx}2 ms, but the relationship is complicated by several factors. Finally, measurements of the radial profiles of the Reynolds shear stresses are reported. These radial profiles exhibit many similarities for several shots, and a region with positive radial gradient is seen to be coincident with local flow shear.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduced model simulations of the scrape-off-layer heat-flux width and comparison with experiment

Reduced model simulations of turbulence in the edge and scrape-off-layer (SOL) region of a spherical torus or tokamak plasma are employed to address the physics of the scrape-off-layer heat flux width. The simulation model is an electrostatic two-dimensional fluid turbulence model, applied in the plane perpendicular to the magnetic field at the outboard midplane of the torus. The model contains curvature-driven-interchange modes, sheath losses, and both perpendicular turbulent diffusive and convective (blob) transport. These transport processes compete with classical parallel transport to set the SOL width. Midplane SOL profiles of density, temperature and parallel heat flux are obtained from the simulation and compared with experimental results from the National Spherical Torus Experiment (NSTX) to study the scaling of the heat flux width with power and plasma current. It is concluded that midplane turbulence is the main contributor to the SOL heat flux width for the low power H-mode discharges studied, while additional physics is required to explain the plasma current scaling of the SOL heat flux width observed experimentally in higher power discharges. Intermittent separatrix spanning convective cells are found to be the main mechanism that sets the near-SOL width in the simulations. The roles of sheared flows and blob trapping vs. emission are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NSTX plasma response to lithium coated divertor

NSTX experiments have explored lithium evaporated on a graphite divertor and other plasma-facing components in both L- and H- mode confinement regimes heated by high-power neutral beams. Improvements in plasma performance have followed these lithium depositions, including a reduction and eventual elimination of the HeGDC time between discharges, reduced edge neutral density, reduced plasma density, particularly in the edge and the SOL, increased pedestal electron and ion temperature, improved energy confinement and the suppression of ELMs in the H-mode. However, with improvements in confinement and suppression of ELMs, there was a significant secular increase in the effective ion charge Z(eff) and the radiated power in H-mode plasmas as a result of increases in the carbon and medium-Z metallic impurities. Lithium itself remained at a very low level in the plasma core, < 0.1%. Initial results are reported from operation with a Liquid Lithium Divertor (LLD) recently installed. (C) 2010 Elsevier B.V. All rights reserved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Snowflake Divertor Configuration in NSTX

Steady-state handling of divertor heat flux is a critical issue for present and future conventional and spherical tokamaks with compact high power density divertors. A novel 'snowflake' divertor (SFD) configuration that takes advantage of magnetic properties of a second-order poloidal null has been predicted to have a larger plasma-wetted area and a larger divertor volume, in comparison with a standard first-order poloidal X-point divertor configuration. The SFD was obtained in 0.8 MA, 4-6 MW NBI-heated H-mode discharges in NSTX using two divertor magnetic coils. The SFD led to a partial detachment of the outer strike point even in low-collisionality scrape-off layer plasma obtained with lithium coatings in NSTX. Significant divertor peak heat flux reduction and impurity screening have been achieved simultaneously with good core confinement and MHD properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Turbulent Transport and the Scrape-off-layer Width

The two-dimensional fluid turbulence code SOLT is employed to study the role of midplane turbulence on the scrape-off-layer (SOL) heat flux width of tokamak plasmas. The physics simulated includes curvature-driven-interchange modes, sheath losses, and perpendicular turbulent diffusive and convective (blob) transport. Midplane SOL profiles of density, temperature and parallel heat flux are obtained from the simulation and compared with experimental results from the National Spherical Torus Experiment (NSTX) to study the scaling of the heat flux width with power and plasma current. It is concluded that midplane turbulence is the main contributor to the SOL width for the low power ELM-free H-mode discharges studied, while additional physics is required to explain the plasma current scaling of the SOL width observed experimentally in higher power discharges. Additional simulations predict a transition to a convectively-dominated SOL at critical values of power and connection length.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Quiet periods in edge turbulence preceding the L-H transition in the National Spherical Torus Experiment

This paper describes the first observations in the National Spherical Torus Experiment (NSTX) [S. M. Kaye et al., Phys. Plasmas 8, 1977 (2001)] of ''quiet periods'' in the edge turbulence preceding the low-to-high (L-H) mode transition, as diagnosed by the gas puff imaging (GPI) diagnostic near the outer midplane separatrix. During these quiet periods the GPI D{sub {alpha}}light emission pattern was transiently similar to that seen during H-mode, i.e., with a relatively small fraction of the GPI light emission located outside the separatrix. These quiet periods had a frequency of {approx}3 kHz for at least 30 ms before the L-H transition, and were correlated with changes in the direction of the local poloidal velocity. The GPI turbulence images were also analyzed to obtain an estimate for the dimensionless poloidal shearing S=(dV{sub p}/dr)(L{sub r}/L{sub p}){tau}. The values of S were strongly modulated by the quiet periods but did not significantly vary during the {approx}30 ms preceding the L-H transition. Since neither the quiet periods nor the shear flow increased immediately preceding the L-H transition, neither of these appears to be the trigger for this transition, at least for these cases in NSTX.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Solenoid-Less Plasma Start-Up in NSTX Using Transient CHI

Experiments in NSTX have now unambiguously demonstrated the coupling of toroidal plasmas produced by the method of transient Coaxial Helicity Injection (CHI) to inductive sustainment and ramp-up of the toroidal current. The coupled discharges have ramped up to 700 kA and transitioned into H-mode with low inductance typical of the type of discharges needed for long-pulse operation, demonstrating the compatibility of the CHI startup method to conventional inductive operation used since the start of tokamak research. The method was first demonstrated on the smaller concept exploration device HIT-H at the University of Washington. These new results that were obtained on a machine built with mainly conventional components and on a size scale closer to a Component Test Facility, demonstrate that CHI is a viable solenoid-free plasma startup method for future STs and Tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Local Scrape-Off Layer Control Using Biased electrodes in NSTX

An experiment was designed to test the theory that biased electrodes can affect the local scrape-off layer (SOL) width by creating a strong radial ExB drift [Cohen, R.H. and Ryutov, D.D, Nucl. Fusion 37, 621 (1997)]. These electrodes were located near the outer midplane in the SOL of the National Spherical Torus Experiment (NSTX). The electrodes were biased at up to {+-} 100 Volts, and the radial profile of the plasma between them was measured by an array of Langmuir probes. The biasing caused large changes in the local SOL profiles at least qualitatively consistent with this theory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Primary edge localized mode filament structure in the National Spherical Torus Experiment

Edge localized modes (ELMs) are routinely seen in the National Spherical Torus Experiment (NSTX) [M. Ono, Nucl. Fusion 40, 557 (2000)]. These unstable modes give rise to plasma filaments that burst radially outward during the nonlinear phase of the instability, moving across flux surfaces into the scrape-off layer. Fast-frame visible imaging is used in NSTX to study the evolution and characteristics of the post-ELM filaments. These edge filaments, which are well aligned with the local magnetic field, are seen to evolve from a perturbation of the edge that within 40-50 {mu}s develops into the relatively high density/temperature primary filaments. The distribution of primary filaments in toroidal angle is seen to agree with a random model with moderate average toroidal mode numbers. At the same time, gas puff imaging shows that the perturbation of the edge leading to the burst of the ELM into the scrape-off layer is characterized by a broadband increase in fluctuations at much smaller poloidal wavelengths ({lambda}{sub pol}{approx}2-12 cm). These two measurements suggest that early development of turbulence may play a role in the development of primary ELM filamentation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Biased Electrodes for SOL Control in NSTX

Small electrodes were installed in the outer-midplane edge of NSTX to attempt to control the local width of the scrape-off layer (SOL) by creating an outward E(pol)xB flow. When the applied voltage between electrodes was 90 V, the density between these electrodes increased by a factor of 3-10 over a radial width of similar to 4 cm. Thus a local control of the SOL plasma density was obtained. (C) 2009 Elsevier B.V. All rights reserved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

MARFE Stability and Movement in an ELMy H-mode NSTX Discharge

The results of a comparison of Multifaceted Asymmetric Radiation From the Edge (MARFE) theory with experiment in the National Spherical Torus Experiment (NSTX) are presented. A variety of MARFE behavior was observed using a fast-framing camera. A basic MARFE theory was applied to NSTX Multi-Pulse Thomson Scattering (MPTS) and Charge-Exchange Recombination Spectroscopy (CHERS) data. MARFE theory showed some limited agreement with experiment, but uncertainty in the separatrix location constrained the analysis. A method based on shifting iso-T(e) flux surfaces was used to estimate the separatrix location. The movements of MARFEs in NSTX are interpreted to result from diamagnetic heat flux driven drifts relative to the E x B drift and imply slowing edge poloidal rotation and/or changing edge profiles before a large ELM. (C) 2009 Elsevier B.V. All rights reserved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Secondary ELM Filaments in NSTX

Filamentary structures are observed in the scrape-off layer of the National Spherical Torus Experime05nt during ELMs. While the primary filaments correspond to a direct result of the ELM event, the 'secondary' filaments which occur generally later but still within 1 ms of the ELM onset are observed to have the same characteristics as inter-ELM filaments (or blobs): poloidal auto-correlation lengths of similar to 4 cm, broadband frequency and poloidal wave number spectra and radial velocities of 1-2 km/s. At the same time, no MHD modes are observed during the phase in which secondary filaments are present. (C) 2009 Elsevier B.V. All rights reserved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Diagnostics for the biased electrode experiment on NSTX

A linear array of four small biased electrodes was installed in NSTX in an attempt to control the width of the scrape-off layer by creating a strong local poloidal electric field. The set of electrodes was separated poloidally by a 1 cm gap between electrodes and were located slightly below the midplane of NSTX, 1 cm behind the rf antenna, and oriented so that each electrode is facing approximately normal to the magnetic field. Each electrode can be independently biased to {+-}100 V. Present power supplies limit the current on two electrodes to 30 A and the other two to 10 A each. The effect of local biasing was measured with a set of Langmuir probes placed between the electrodes and another set extending radially outward from the electrodes, and also by the gas puff imaging diagnostic located 1 m away along the magnetic field lines intersecting the electrodes. Two fast cameras were also aimed directly at the electrode array. The hardware and controls of the biasing experiment will be presented and the initial effects on local plasma parameters will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗