Search NASA⌕ Search

Engineering topics

Marc Gibson

Publications and source records attributed to Marc Gibson.

4 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

A Deployable 40 kWe Lunar Fission Surface Power Concept

Continuous power at the kilowatt level will be imperative for future lunar users including crew infrastructure, future science, and in-situ resource utilization (ISRU). The Compass Team explored both 10 kWe and 40 kWe concepts, assuming planned lander and rover capabilities. Both concepts found that a crew pressurized rover chassis, repurposed for deploying reactor power components, could place a fission surface power system (FSPS) at least one km from users. While the 10 kWe fission power system (FPS) could be deployed as a single unit, the 40 kWe system was too large and had to be deployed in multiple trips with the same rover. Key technologies and design approaches included a high-assay low-enriched uranium (HALEU), yttrium hydride (YH) moderated heat pipe reactor, Stirling convertors, deployable radiators based on International Space Station (ISS) designs, and power conversion/transmission at ±2800 VDC for a one km remote distance.

Fission Power↗
NASA NTRSDate not supplied

Consolidation of A Sodium Heat Pipe and Stirling Engine for Fission Surface Power

The Consolidated Heat Pipe (CHP) is a new design in which a sodium heat pipe is welded directly to the hot end of the Stirling engine to deliver thermal power more efficiently. The new integrated interface aims to reduce the large temperature drop (about 120 °C) that was measured across the bolted clamp joint between the Stirling engine and the heat pipes during the Kilopower Reactor Using Stirling TechnologY (KRUSTY) test from 2018. Initial testing and characterization of the CHP was performed in ambient air at the NASA Glenn Research Center (GRC). In the test, the heat pipe evaporator section was heated with a tube furnace. The thermal power was then transported to the Stirling engine integrated with a linear alternator that produced electrical power. The CHP has been tested at a hot end temperature ranging from 600 °C - 800 °C and a variety of other Stirling engine parameters (cold end temperature, piston amplitude and pressure). The results show that the temperature drop between the Stirling engine and the heat pipe has been reduced to 2°C - 4 °C. An overall temperature drop of 20 °C – 60 °C was also noted within the heat pipe depending on the combination of parameters mentioned above. Overall, it has been shown that the new Consolidated Heat Pipe design significantly improved the thermal interface to the Stirling engine.

Consolidated↗
NASA NTRSDate not supplied

Vacuum Operation of Consolidated Heat Pipe (CHP) for Fission Surface Power

Consolidated Heat Pipe (CHP) is a new technology that enables direct thermal power delivery to the hot-end of a Stirling engine using a heat pipe--a two phase passive heat transfer device. CHP was developed after the efforts of the Kilopower Using Stirling TechnologY (KRUSTY) test where a heat pipe was used to deliver thermal power from a fission-basedreactor to a Stirling engine to produce 1 kWe of useable electrical power in 2018. Large thermal losses were noted during the KRUSTY test where a temperature drop of 145 °C was measured between the heat pipe’s condenser and the engine’s hot-end. The Consolidated Heat Pipe was designed to address and mitigate this temperature loss. CHP was designed, built and tested at the Glenn Research Center (GRC). The initial test was performed in ambient air conditions, and the results were presented in “Consolidation of a Sodium Heat Pipe and Stirling Engine for Fission Surface Power” at the Thermal Fluids Analysis Workshop in 2023. Researchers at GRC have tested this technology again in a vacuum environment in 2024. Results show that the heat pipe and the hot-end of the Stirling engine are isothermal with a minimal temperature differential of approximately 2.5 °C in varying operational states. The Consolidated Heat Pipe technology has proven to be an efficient way of delivering thermal power directly to Stirling engines.

Greeta J Thaikattil↗