Search NASA⌕ Search

Engineering topics

Marc Shaw-Lecerf

Publications and source records attributed to Marc Shaw-Lecerf.

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Unsteady Pressure-Sensitive-Paint Shot Noise Reduction

In the study of unsteady Pressure-Sensitive Paint (uPSP) image data sets, pixel intensity values collected by Phantom cameras from multiple perspectives are used to calculate the surface pressure of an experimental model. This paper focuses on mitigation of shot noise which is introduced into the image data set by the cameras. Shot noise impacts the quality of data collected, increasing the system error in its pressure value calculations. This paper characterises statistical methods to reduce shot noise within experimental data by taking an average or weighted average across an area of pixels of their respective counts. Each combined-pixel has a higher total effective intensity value and therefore exhibits reduced noise throughout its time history. This is demonstrated by calculating the standard deviations of the combined pixel values through time, which decrease as the combined pixel area increases. Finally, these methods are compared across experimental wind tunnel conditions to examine their effectiveness at different Mach numbers. Ultimately, the results are used to recommend a blur filter type and size which will be applied to the raw image data prior to processing, as well as a minimum camera resolution for future experiments. Downstream of the filter application, the software to convert the 2D image data sets into surface pressure readings on a 3D grid use a ratio of decimation that assigns multiple pixels to each 3D grid node. This decimation ratio will also be aligned with the size of the blur filter, resulting in a more manageable data set size and compromised spatial resolution. Combined with the effect of the blur filter, the resulting pixel intensity readings will exhibit significantly reduced shot noise, reducing the magnitude of uncertainty and error in the final calculated pressure. For future tests, the camera spatial resolution must be sufficient to capture small flow and model features even after the recommended blur filter is applied. The image data set is taken from a uPSP experiment of the Space Launch System Block 1 cargo vehicle model in September 2019.

Lucy Tang↗
NASA NTRS2021

Unsteady Pressure-Sensitive Paint (UPSP) Shot Noise Reduction

In the study of unsteady Pressure-Sensitive Paint (uPSP) image data sets, pixel intensity values collected by Phantom cameras from multiple perspectives are used to calculate the surface pressure of an experimental model. This paper focuses on mitigation of shot noise which is introduced into the image data set by the cameras. Shot noise impacts the quality of data collected, increasing the system error in its pressure value calculations. This paper characterises statistical methods to reduce shot noise within experimental data by taking an average or weighted average across an area of pixels of their respective counts. Each combined-pixel has a higher total effective intensity value and therefore exhibits reduced noise throughout its time history. This is demonstrated by calculating the standard deviations of the combined pixel values through time, which decrease as the combined pixel area increases. Finally, these methods are compared across experimental wind tunnel conditions to examine their effectiveness at different Mach numbers. Ultimately, the results are used to recommend a blur filter type and size which will be applied to the raw image data prior to processing, as well as a minimum camera resolution for future experiments. Downstream of the filter application, the software to convert the 2D image data sets into surface pressure readings on a 3D grid use a ratio of decimation that assigns multiple pixels to each 3D grid node. This decimation ratio will also be aligned with the size of the blur filter, resulting in a more manageable data set size and compromised spatial resolution. Combined with the effect of the blur filter, the resulting pixel intensity readings will exhibit significantly reduced shot noise, reducing the magnitude of uncertainty and error in the final calculated pressure. For future tests, the camera spatial resolution must be sufficient to capture small flow and model features even after the recommended blur filter is applied. The image data set is taken from a uPSP experiment of the Space Launch System Block 1 cargo vehicle model in September 2019.

Lucy Tang↗
NASA NTRSDate not supplied

Launch Vehicle Loads Analysis Using Pressure-Sensitive Paint

Pressure transducers have been the instrumentation of choice for measuring unsteady flow phenomena. With recent advances in high-speed cameras, high-powered LEDs, and fast-response, pressure-sensitive paint, the unsteady pressure-sensitive paint (uPSP) technique has become a valuable alternative for production wind tunnel facilities, enabling time-resolved measurements of unsteady pressure fluctuations over a dense spatial grid on a wind tunnel model. Launch vehicle ground tests have proven to be a particularly well-matched application for uPSP due to the high signal level relative to tunnel background acoustics, relatively simple camera optical access, and rigidity of the model in wind-on test conditions. This presentation will highlight recent advances in data reduction of uPSP measurement data from recent launch vehicle wind tunnel tests at the NASA Ames Unitary Plan Wind Tunnel Complex (UPWT). The system can provide both localized surface pressure spectra as well as regional or zonal estimates of turbulence correlation model parameters. In addition, integrated vehicle-scale loads can be provided for buffet analysis. Data is reduced at the on-premise NASA Advanced Supercomputer (NAS) Division for just-in-time delivery of results during an ongoing wind tunnel test.

pressure-sensitive paint↗
NASA NTRSDate not supplied

Unsteady Pressure Sensitive Paint Camera Calibration Improvements

New challenges have arisen in processing a significantly increased volume of data collected during recent large-scale demonstrations of unsteady pressure-sensitive paint. Techniques designed for several thousands of images collected in a lab do not necessarily scale to tens of millions collected in a large-scale test. New techniques are needed to meet the tighter requirements on robustness and accuracy that accompany larger wind tunnel models, higher camera resolution, and more run conditions per test. This paper outlines several such techniques and improvements in regard to the camera calibration process.

Camera calibration↗
NASA NTRSDate not supplied

Implementation of the Lifetime Method in uPSP Measurements

At NASA Ames Research Center, unsteady pressure-sensitive paint (uPSP) measurements are obtained using the ‘intensity method’ which measures paint luminescence in response to a continuous, constant excitation. These measurements are obtained using high-speed cameras and are processed into fluctuating components of pressure. However, the nature of the intensity method also requires a separate steady state (time mean) pressure measurement to be obtained. This steady state measurement has typically been obtained using a separate set of PSP equipment that uses the ‘lifetime method’, which uses pulsed excitation to measure paint decay lifetime. If the lifetime method were implemented in the high-speed uPSP system, both the fluctuating and mean components of pressure could be obtained with a single system. This would greatly streamline setup, operations, and processing. In this paper, we describe work performed at the Fluid Mechanics Laboratory at NASA Ames to implement the lifetime method in our uPSP system. The uPSP acquisition system uses Phantom v2512 high-speed cameras, and it was initially uncertain if results of adequate quality could be obtained - their high framerate comes at the cost of several undesirable characteristics, which are explored in this paper. It was also uncertain if illumination using LED lamps, rather than a stronger source such as lasers, would be adequate. The data acquisition and data processing are discussed and the results analyzed. It was found that satisfactory lifetime method results can indeed be obtained using these high-speed cameras and LED lamps. This will allow the uPSP system to be greatly simplified and will have a large operational impact on how uPSP data is acquired in future wind tunnel tests.

Pressure Sensitive Paint↗