Engineering topics

Marchese, Anthony

Publications and source records attributed to Marchese, Anthony.

17 records

DOE OSTI2022

Influence of NOx chemistry on the prediction of natural gas end-gas autoignition in CFD engine simulations

Natural gas (NG) represents a promising low-cost/low-emission alternative to diesel fuel when used in high-efficiency internal combustion engines. Advanced combustion strategies utilizing high EGR rates and controlled end-gas autoignition can be implemented with NG to achieve diesel-like efficiencies; however, to support the design of these next-generation NG ICEs, computational tools, including single- and multi-dimensional simulation packages will need to account for the complex chemistry that can occur between the reactive species found in EGR (including NOx) and the fuel. Research has shown that NOx plays an important role in the promotion/inhibition of large hydrocarbon autoignition and when accounted for in CFD engine simulations, can significantly improve the prediction of end-gas autoignition for these fuels. However, reduced NOx-enabled NG mechanisms for use in CFD engine simulations are lacking, and as a result, the influence of NOx chemistry on NG engine operation remains unknown. Here, we analyze the effects of NOx chemistry on the prediction of NG/oxidizer/EGR autoignition and generate a reduced mechanism of a suitable size to be used in engine simulations. Results indicate that NG ignition is sensitive to NOx chemistry, where it was observed that the addition of EGR, which included NOx, promoted NG autoignition. The modified mechanism captured well all trends and closely matched experimentally measured ignition delay times for a wide range of EGR rates and NG compositions. Here, the importance of C2-C3 chemistry is noted, especially for wet NG compositions containing high fractions of ethane and propane. Finally, when utilized in CFD simulations of a Cooperative Fuels Research (CFR) engine, the new reduced mechanism was able to predict the knock onset crank angle (KOCA) to within one crank angle degree of experimental data, a significant improvement compared to previous simulations without NOx chemistry.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2022

Effect of fuel composition and EGR on spark-ignited engine combustion with LPG fueling: Experimental and numerical investigation

This paper presents an experimental and numerical investigation of a spark-ignited (SI) cooperative fuel research (CFR) engine fueled with different liquefied petroleum gas (LPG) fuels and exhaust gas recirculation (EGR). Here, the effects of LPG fuel composition on engine combustion characteristics are initially evaluated at two different compression ratios (CR). Results show normal combustion at CR 7 and heavy knocking combustion at CR 10 for all the tested fuels, with a more substantial impact for the LPG fuel with high proportions of n-butane species. The Livengood-Wu (LW) integral method is then used to analyze the knock occurrence risk of individual fuel based on the reactivity of the tested fuels. The introduction of EGR then demonstrates the potential of knock intensity reduction below the borderline knock limit. A zonal-based kinetic interactions study is also performed to understand the knock mitigation effectiveness of EGR over the pressure–temperature domain relevant to SI engine operation. Finally, a multidimensional, computational fluid dynamics (CFD) simulation model is shown to predict the LPG combustion characteristics and presents the evolution of in-cylinder temperature and chemical species to demonstrate the development of end-gas autoignition events without and with EGR.

02 PETROLEUM↗

DOE OSTI2022

Heavy Duty Natural Gas Single Cylinder Research Engine Installation, Commissioning, and Baseline Testing

Natural Gas (NG) Internal Combustion Engines (ICE) are a promising alternative to diesel engines for on-road heavy-duty applications to reduce greenhouse gas and harmful pollutant emissions. NG engines have not been widely adopted due to the lower thermal efficiency compared with diesel engine counterparts. To develop the base knowledge required to reach the desired efficiency, a Single Cylinder Engine (SCE) is the most effective platform to acquire reliable and repeatable data. A SCE test cell was developed using a Cummins 15-liter six-cylinder heavy-duty engine block modified to fire one cylinder (2.5-liter displacement). A Woodward Large Engine Control Module (LECM) is integrated to permit implementation of real-time advanced combustion control. Intake and exhaust characteristics, fuel composition, and exhaust gas recirculated substitution rate (EGR) are fully adjustable. A high-speed data acquisition system acquires in-cylinder, intake, and exhaust pressure for combustion analysis. The baseline testing shows reliable and consistent results for engine thermal efficiency, indicated mean effective pressure (IMEP), and coefficient of variance of the IMEP over a wide range of operating conditions while achieving effective control of all engine control and operation variables. This test cell will be used to conduct a research program to develop new and innovative control algorithms and CFD optimized combustion chamber designs, allowing ultra-high efficiency and low emissions for NG ICE heavy-duty on-road applications.

03 NATURAL GAS↗

DOE OSTI2022

A Study of Propane Combustion in a Spark-Ignited Cooperative Fuel Research (CFR) Engine

Liquefied petroleum gas (LPG), whose primary composition is propane, is a promising candidate for heavy-duty vehicle applications as a diesel fuel alternative due to its CO 2 reduction potential and high knock resistance. To realize diesel-like efficiencies, spark-ignited LPG engines are proposed to operate near knock-limit over a wide range of operating conditions, which necessitates an investigation of fuel-engine interactions that leads to end-gas autoignition with propane combustion. This work presents both experimental and numerical studies of stoichiometric propane combustion in a sparkignited (SI) cooperative fuel research (CFR) engine. Engine experiments are initially conducted at different compression ratio (CR) values, and the effects of CR on engine combustion are characterized. A three-pressure analysis (TPA) model based on the two-zone combustion concept is developed in GT-Power and validated using test results to estimate in-cylinder wall temperatures, residual gas fraction, etc. This model is further utilized to examine end-gas chemistry by enabling the SI turbulent flame combustion and unburned gas chemical kinetics modules. Finally, a three-dimensional (3D) computational fluid dynamic (CFD) model of the CFR engine is developed in CONVERGE, where the G-equation and SAGE detailed chemical kinetics models are implemented for combustion modeling. Here, a 153 species reduced chemical kinetics mechanism derived from the detailed NUIGMech1.1 mechanism based on the ignition delay and laminar flame speed (LFS) studies is used to generate an LFS lookup table and to describe end-gas autoignition chemistry. Multi-cycle Reynolds-averaged Navier-Stokes (RANS) simulations are then performed for the tested CRs, and the numerical model is shown to be capable of predicting the propane combustion characteristics, particularly the end-gas autoignition behavior.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2022

Bulk Spray and Individual Plume Characterization of LPG and Iso-Octane Sprays at Engine-Like Conditions

This study presents experimental and numerical examination of directly injected (DI) propane and iso-octane, surrogates for liquified petroleum gas (LPG) and gasoline, respectively, at various engine like conditions with the overall objective to establish the baseline with regards to fuel delivery required for future high efficiency DI-LPG fueled heavy-duty engines. Sprays for both iso-octane and propane were characterized and the results from the optical diagnostic techniques including high-speed Schlieren and planar Mie scattering imaging were applied to differentiate the liquid-phase regions and the bulk spray phenomenon from single plume behaviors. The experimental results, coupled with high-fidelity internal nozzle-flow simulations were then used to define best practices in CFD Lagrangian spray models. Optical imaging revealed that unlike iso-octane, propane’s spray propagation was fed by its flash boiling, spray collapse, and high degree of vaporization, resulting in a direct proportionality of propane’s penetration length to temperature. These unique features of propane and its variation from iso-octane’s spray pattern, contributed to its classification as an unconventional spray. Appropriate corrections to the injection and breakup models were developed to reproduce the under-expanded jet dynamics and to mimic the flash boiling-driven spray development observed with propane sprays. The simulation results were found to be sensitive to cone and inclusion angles of the blob injector. The current work represents a first assessment of the capability of the commonly available models for engine-spray simulations and highlights the fact that, despite the reasonable agreement obtained in the fuel vapor morphology, the representation of the liquid phase lacks accuracy and requires further model development.

02 PETROLEUM↗

DOE OSTI2022

The Impact of LPG Composition on Performance, Emissions, and Combustion Characteristics of a Pre-mixed Spark-Ignited CFR Engine

Research on alternative fuels has made significant progress as demands for cleaner and more efficient engine operation intensifies. Liquefied petroleum gas (LPG) can offer a potential alternative fuel route in the Diesel fuel dominated heavy-duty transportation sector due to its low cost, high anti-knock limit relative to gasoline, and reduced emission levels. In this work, experimental investigations are performed to study the effects of LPG compositions on performance, emissions, and combustion behavior of a spark-ignited (SI) cooperative fuel research (CFR) engine under stoichiometric conditions. Four LPG blends (chemically pure propane, a representative US blend, HD-5, and a representative European blend) representing the present LPG market are chosen. The impact of fuel composition is studied under different compression ratios (CR), ranging from 7:1 to 10:1 with one-unit increments, and at constant engine speed, intake manifold air pressure (IMAP) and 50% burn crank angle (CA50). The results show that fuel composition has minimal effect on engine efficiency over the CR range 7:1 to 10:1. Engine-out emissions are substantially affected by fuel compositions with the representative European blend indicating higher unburned hydrocarbon (UHC) emissions, particularly at higher CR. The representative US blend emits the lowest brake specific CO (bsCO) averaged over the tested CR range. With the increase of CR, end-gas autoignition intensifies for all blends and the representative European blend demonstrates the highest knock intensity of all tested blends, due to the presence of the more reactive fuel component, n-butane.

Fosudo, Toluwalase↗

DOE OSTI2021

Expanding the Knock/Emissions/Misfire Limits for the Realization of Ultra-Low Emissions, High Efficiency Heavy Duty Natural Gas Engines

The Vehicle Technologies Office funds early-stage, high-risk research to develop technology upon which industry can implement innovative transportation energy technologies that increase efficiency, decrease cost, and expand use of domestic energy sources, such as natural gas (NG). To improve the viability of medium and heavy-duty vehicles the natural gas engine efficiency must be closer to that of diesel. This work addresses fundamental limitations to achieve diesel-like efficiencies in heavy duty on-road natural gas engines. The primary goal of this research is to achieve diesel-like efficiencies in heavy duty on-road NG engines, focusing on the Cummins 15 liter engine platform (baseline diesel efficiency of 44% at peak torque). That goal has been achieved, though more work is needed to facilitate practical implementation of the developed technologies.

03 NATURAL GAS↗

DOE OSTI2021

Influence of NOx Chemistry on the Prediction of Natural Gas End-Gas Autoignition

Research on the influence of NOx (NO/NO2) chemistry on HC oxidation has shown that NOx plays an important role in the promotion/inhibition of HC autoignition [1-6]. Current data for n-heptane, iso-octane, ethanol, and toluene [3, 4] have shown that NO chemistry inhibits autoignition at low temperatures and concentrations. However, at medium and high temperatures and low concentrations, autoignition is promoted, decreasing the Negative Temperature Coefficient (NTC) effect. This autoignition promotion, however, becomes weaker as NO concentrations are increased. Additionally, fundamental kinetics studies have suggested that NOx chemistry also promotes the autoignition of smaller HC, such as CH4 [7-10], C2H6 [11-14], and C3H8 [15]. Additionally to the chemical kinetics studies, a growing body of evidence supports the importance of NOx chemistry on SI engine simulations [16, 17]. Foong et al. [18] suggested that the addition of NO in their models significantly improved the agreement between simulations and experiments where the onset of knock was advanced due to the presence of NO, and Morganti et al. [19] showed that NO addition in the residual-gas was necessary for their models to obtain good agreement with experimental data. Lastly, Mohr et al. [20, 21] investigated the effect of Natural Gas (NG) reactivity and EGR substitution rate and composition on homogeneous ignition delay, flame speeds, and EGAI for stoichiometric NG/oxidizer/EGR blends. They observed that the addition of EGR composed of only inert species (CO2 and Ar) suppressed homogeneous autoignition in all NG fuels tested under all conditions. However, for all NG fuels tested, increasing EGR rates with reactive species (Ar, CO2, CO, and NO) promoted homogeneous autoignition under all conditions, thus reproducing the same trends for various NG fuel compositions that were observed in other studies and fuels. For this reason, a study is being conducted to analyze the effects of NOx chemistry on the prediction of NG/air/EGR homogeneous autoignition. This study has been divided into two tasks. First, the addition of NOx chemistry to the ARIES82 mechanism [20] is being validated using homogeneous ignition delay data collected by Mohr [20, 21]. Second, once the new modified mechanism with NOx reactions has been validated, it will be employed on engine multi-dimensional modeling presented in [22, 23] to analyze the influence of NOx chemistry on NG EGAI. Results thus far have shown that homogeneous ignition delay calculations are sensitive to NOx chemistry, where the modified mechanisms captured well all trends and closely matched the homogeneous ignition delays observed by Mohr et al. Also, the results in this work suggest that NOx chemistry is necessary to correctly capture the trends in NG homogeneous autoignition when EGR with reactive species is used since the opposite behavior is observed when only inert species are considered for the EGR composition.

03 NATURAL GAS↗

DOE OSTI2021

Autoignition of Premixed Liquefied Petroleum Gas in a Rapid Compression Machine: Experimental Results and Chemical Kinetic Mechanism Reduction

Liquefied petroleum gas (LPG) has many properties that make it an attractive alternative fuel such as lower cost than conventional fuels and an established distribution infrastructure. The development of high efficiency, spark ignited LPG engines is currently limited by engine knock and misfire. The knock and misfire limits are further complicated by the wide range of chemical reactivity in LPG, particularly in international markets. In this study, a rapid compression machine (RCM) was used to characterize the effects of variation in LPG fuel reactivity, equivalence ratio, and exhaust gas recirculation (EGR) on autoignition of LPG/oxidizer/inert/EGR blends. Experiments were conducted with 100% propane (C3H8) and blends of propane with propene, ethane, isobutane, and n-butane. EGR was simulated with mixtures of Ar, CO2, CO, and NO at substitution percentages from 0 to 30 mass percent. Equivalence ratio was varied from 0.75 to 1.5. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures and temperatures of 23 to 25 bar and 701 to 921 K, respectively. Zero-dimensional simulations of the RCM experiments were performed using Chemkin with several detailed chemical kinetic mechanisms to determine their suitability at predicting ignition delay periods. Multiple reduced chemical kinetic mechanisms were created from the NUIGMech1.1 mechanism to determine the optimal balance between accuracy and computational efficiency for future three-dimensional, time-dependent spark-ignited engine computations.

42 ENGINEERING↗

DOE OSTI2020

CONTROLLED END GAS AUTO IGNITION WITH EXHAUST GAS RECIRCULATION ON A STOICHIOMETRIC, SPARK IGNITED, NATURAL GAS ENGINE

The goal of this study is to address fundamental limitations to achieving diesel-like efficiencies in heavy duty on-highway natural gas (NG) engines. Engine knock and misfire are barriers to pathways leading to higher efficiency engines. This study explores enabling technologies for development of high efficiency stoichiometric, spark ignited, natural gas engines. These include design strategies for fast and stable combustion and higher dilution tolerance. Additionally, advanced control methodologies are implemented to maintain stable operation between knock and misfire limits. To implement controlled end- gas autoignition (C-EGAI) strategies a Combustion Intensity Metric (CIM) is used for ignition control with the use of a Woodward large engine control module (LECM). Tests were conducted using a single cylinder, variable compression ratio, cooperative fuel research (CFR) engine with baseline conditions of 900 RPM, engine load of 800 kPa indicated mean effective pressure (IMEP), and stoichiometric air/fuel ratio. Exhaust gas recirculation (EGR) tests were performed using a custom EGR system that simulates a high pressure EGR loop and can provide a range of EGR rates from 0 to 40%. The experimental measurements included the variance of EGR rate, compression ratio, engine speed, IMEP, and CIM. These five variables were optimized through a Modified Box- Benken design Surface Response Method (RSM), with brake efficiency as the merit function. A positive linear correlation between CIM and f-EGAI was identified. Consequently, CIM was used as the feedback control parameter for C-EGAI. As such, implementation of C-EGAI effectively allowed for the utilization of high EGR rates and CRs, controlling combustion between a narrower gap between knock and lean limits. The change from fixed to parametric ignition timing with CIM targeted select values of f-EGAI with an average coefficient of variance (COV) of peak pressure of 5.4. The RSM efficiency optimization concluded with operational conditions of 1080 RPM, 1150 kPa IMEP, 10.55:1 compression ratio, and 17.8% EGR rate with a brake efficiency of 21.3%. At this optimized point of peak performance, a f-EGAI for C-EGAI was observed at 34.1% heat release due to auto ignition, a knock onset crank angle value of 10.3° aTDC and ignition timing of - 24.7° aTDC. This work has demonstrated that combustion at a fixed f-EGAI can be maintained through advanced ignition control of CIM without experiencing heavy knocking events.

Cooperative Fuel Research Engine, Auto Ignition, E↗

DOE OSTI2020

MULTI-DIMENSIONAL MODELING OF THE CFR ENGINE FOR THE INVESTIGATION OF SI NATURAL GAS COMBUSTION AND CONTROLLED END-GAS AUTOIGNITION

Engine knock and misfire are barriers to pathways leading to high-efficiency Spark-Ignited (SI) Natural Gas engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emission limits and the wide range of chemical reactivity in pipeline quality natural gas. Depending on the region and the source of the natural gas, its reactivity, described by its methane number (analogous to the octane number for liquid SI fuels) can span from 65 - 95. In order to realize diesel-like efficiencies, SI natural gas engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding the combustion-engine interactions pertaining to flame propagation and end-gas autoignition (EGAI). However, EGAI, if controlled, provides an opportunity to increase SI natural gas engine efficiency by increasing combustion rate and the total burned fuel, mitigating the effects of the slow flame speeds of natural gas fuels which generally reduce BMEP and increase unburned hydrocarbon emissions. For this reason, in order to study EGAI phenomenon, the present work highlights multi-dimensional computational fluid dynamics (CFD) models of the Cooperative Fuel Research (CFR) engine. The CFR engine models are used to investigate fuel-engine interactions that lead to EGAI with natural gas, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). A Three-Pressure Analysis, performed with GT-Power, was used to estimate initial and boundary conditions for the three-dimensional CFD model. CONVERGE CFD v2.4 was used for the three-dimensional CFD modeling where the level set G-Equation model and SAGE detailed chemical kinetics solver were used. An assessment of the different modeling approaches is also provided to evaluate their limitations, advantages and disadvantages, and for which situations they are most applicable. Model validation was performed with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction, and IMEP and shows good agreement in Peak Cylinder Pressure (PCP), PCP crank angle, and the location of the 10%, 50%, and 90% mass fraction burned (CA10, CA50, and CA90, respectively). The models can predict the onset crank angle and pressure rise rate for light, medium, and heavy EGAI under a variety of fuel reactivities and engine operating conditions.

Bestel, Diego↗

DOE OSTI2020

Investigation of the end-gas autoignition process in natural gas engines and evaluation of the methane number index

Engine knock and misfire are barriers to pathways leading to high-efficiency Spark-Ignited (SI) Natural Gas (NG) engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by the wide range of chemical reactivity in pipeline quality NG, represented by the Methane Number (MN) (65< MN<95). Understanding the underlying phenomena responsible for engine knock can support the development of predictive tools capable of identifying knock onset/intensity as well as a fuel’s propensity to knock, allowing engine manufacturers to expand the knock envelope and design more efficient/robust SI NG engines. Additionally, there is an opportunity for increased efficiency by controlling levels of end-gas autoignition if this can be predicted and controlled. This work focuses on the development of a novel methodology to understand/predict a fuel’s propensity to knock. This methodology is based on the charge fraction undergoing autoignition, namely fractional end-gas autoignition (F-EGAI), and was developed based on first order laminar flame speeds and ignition delay analysis combined with a 0-D homogeneous batch reactor model. This methodology proved to be suitable to predict a fuel’s propensity to knock, even under conditions when light knock was observed. The simple modeling approach was used to explain the results from a series of MN tests with multiple NG compositions exhibiting a wide range of reactivity compositions and providing insight on why fuels of very different chemical compositions can have the same MN. Finally, a CFD model was developed was used to confirm the methodology capability and provide further insights in the physical and chemical phenomena behind end gas autoignition.

42 ENGINEERING↗

DOE OSTI2020

Methane Emissions from Gathering Compressor Stations in the U.S.

Using results from a nationally representative measurement campaign at 180 gathering compressor stations conducted with nine industry partners, this study estimated emissions for the U.S. gathering sector, where sector-specific emission factors have not been previously available. The study drew from a partner station population of 1705 stations—a significantly larger pool than was available for prior studies. Data indicated that whole gas emission rates from components on gathering stations were comparable to or higher than emission factors utilized by the EPA’s greenhouse gas reporting program (GHGRP) but less than emission factors used for similar components on transmission compressor stations. Field data also indicated that the national population of stations likely has a higher fraction of smaller stations, operating at lower throughput per station, than the data used to develop the per-station emission factor used in EPA’s greenhouse gas inventory (GHGI). This was the first national study to incorporate extensive activity data reported to the GHGRP, including 319 basin-level reports, covering 15,895 reported compressors. Further, combining study emission data with 2017 GHGRP activity data, the study indicated statistically lower national emissions of 1290 [1246–1342] Gg methane per year or 66% [64–69%] of current GHGI estimates, despite estimating 17% [12–22%] more stations than the 2017 GHGI (95% confidence interval). Finally, we propose a replicable method that uses GHGRP activity data to annually update GHGI gathering and boost sector emissions.

03 NATURAL GAS↗

DOE OSTI2020

Using yttrium as an indicator to estimate total rare earth element concentration: a case study of anthracite-associated clays from northeastern Pennsylvania

Abstract This study demonstrated using yttrium (Y) as an indicator to estimate the total rare earth element and Y contents (REY) in coal-associated samples and to facilitate selection of samples with high REY assays in a fast and inexpensive manner. More than 10 anthracite-associated samples were collected from each of three Pennsylvanian sites (sites B, J and C) based on Thorium gamma ray logging suggesting high REY content. Several samples from each site were analyzed by ICP-MS to determine the rare earth distribution patterns and to establish the site-specific linear equations of Y and REY. The Y contents of the remaining samples were measured by a portable X-ray fluorescence analyzer, and the REY values were estimated based on the site-specific linear equation developed earlier. R-squared values above 0.70 were obtained for all the estimation equations from all three sites on both a whole sample basis and an ash basis. Previously, ash content has been widely used as an indicator of high REY content. This may not be applicable for a specific site. Site B in this study is an example where ash contents could not be statistically correlated with REY, so using Y for estimation is more applicable. The demonstrated sample screening process is suitable for samples from sites that share more similar distribution patterns (either MREY or LREY or HREY) as well as for samples from sites that share multiple distribution patterns (LREY/MREY/HREY) depending on the desirable accuracy. The demonstrated process lowers the analytical cost from $70 to 80 dollars per sample to $10–15 per sample while significantly reducing the processing time and acid consumption for ICP digestion. This is particularly true when a relatively large sample size is involved, for example, 100 samples from one site analyzed by ICP-MS/OES.

Yang, Xiaojing↗

NASA NTRS2003

Gravitational Influences on Flame Propagation Through Non-Uniform, Premixed Gas Systems

Flame propagation through non-uniformly premixed (or layered) gases has importance both in useful combustion systems and in unintentional fires. As summarized recently and in previous Microgravity Workshop papers, non-uniform premixed gas combustion receives scant attention compared to the more usual limiting cases of diffusion or uniformly premixed flames, especially regarding the role gravity plays. This paper summarizes our recent findings on gravitational effects on layered combustion along a floor, in which the fuel concentration gradient exists normal to the direction of flame spread. In an effort to understand the mechanism by which the flames spread faster in microgravity (and much faster, in laboratory coordinates, than the laminar burning velocity for uniform mixtures), we have begun making pressure measurements across the spreading flame front that are described here. Earlier researchers, testing in 1g, claimed that hydrostatic pressure differences could account for the rapid spread rates. Additionally, we present the development of a new apparatus to study flame spread in free (i.e., far from walls), non-homogeneous fuel layers formed in a flow tunnel behind an airfoil that has been tested in normal gravity.

Miller, Fletcher J.↗

NASA NTRS2001

Gravitational Influences on Flame Propagation through Non-Uniform, Premixed Gas Systems

Flame propagation through non-uniformly premixed (or layered) gases has importance both in useful combustion systems and in unintentional fires. As summarized previously, non-uniform premixed gas combustion receives scant attention compared to the more usual limiting cases of diffusion or uniformly premixed flames, especially regarding the role gravity plays. This paper summarizes our progress on furthering the knowledge of layered combustion, in which a fuel concentration gradient exists normal to the direction of flame spread. We present experimental and numerical results for flame spread through propanol-air layers formed near the flash point temperature (25 C) or near the stoichiometric temperature (33 C). Both the model and experimental results show that the removal of gravity results in a faster spreading flame, by as much as 80% depending on conditions. This is exactly the opposite effect as that predicted by an earlier model reported. We also found that having a gallery lid results in faster flame spread, an effect more pronounced at normal gravity, demonstrating the importance of enclosure geometry. Also reported here is the beginning of our spectroscopic measurements of fuel vapor.

Miller, Fletcher J.↗

NASA NTRS1999

Gravitational Influences on Flame Propagation Through Non-Uniform Premixed Gas Systems

Flame propagation through non-uniformly premixed gases occurs in several common combustion situations. As summarized in a previous conference paper, non-uniform premixed gas combustion has received scant attention compared to the more usual limiting cases of diffusion or uniformly premixed flames. It is the goal of this research to further our knowledge of layered combustion, in which a fuel concentration gradient exists normal to the direction of flame spread, in particular by focusing on the role that gravity plays. Gravity can affect flame propagation in at least three ways: through a hydrostatic pressure gradient, by altering the initial distribution of fuel vapor, and through buoyantly induced flows once ignition has occurred. An understanding of the phenomena involved is important to fire safety, especially aboard spacecraft since no microgravity data exist. The data obtained will also be useful to verify theoretical models of this problem, which are easier to implement if buoyancy is neglected.

Miller, Fletcher J.↗