Search NASA⌕ Search

Engineering topics

Marciante, J R

Publications and source records attributed to Marciante, J R.

Power Scaling of Single-Frequency Hybrid Brillouin/Ytterbium Fiber Lasers

A coupled-wave rate-equation model, including multiple-order stimulated Brillouin scattering (SBS), is used to study power scaling of hybrid Brillouin/ytterbium fiber lasers. To validate the model, a single-frequency, Brillouin/ytterbium fiber laser was built with a laser output of 40 mW and an optical signal-to-noise ratio greater than 50 dB. The numerical model simulation agrees with the measurements in both fully and partially injection locked regimes. To scale up the laser’s output power, a dual-clad architecture is proposed. In this new configuration, the active Yb-doped fiber provides the nonlinear SBS gain as well as the gain resulting from the excited Yb ions. Numerical modeling including three Stokes orders shows that over 5 W of single-frequency laser output can be achieved with a side-mode suppression ratio (SMSR) of greater than 80 dB. Beyond this power, multi-order SBS affects the laser efficiency and SMSR.

Brillouin scattering↗

All-Fiber Optical Faraday Mirror Using 56-wt%-Terbium-Doped Fiber

An all-fiber optical Faraday mirror that consists of a fiber Faraday rotator and a fiber Bragg grating is demonstrated. The fiber Faraday rotator uses a 21-cm-long section of 56-wt%-terbium-doped silicate fiber. The polarization state of the reflected light is rotated 89 degrees +/- 2 degrees with a 16-dB polarization extinction ratio.

Faraday effect↗

Near-Diffraction-Limited Operation of Step-Index Large-Mode-Area Fiber Lasers Via Gain Filtering

We present, for the first time to our knowledge, an explicit experimental comparison of beam quality in conventional and confined-gain multimode fiber lasers. In the conventional fiber laser, beam quality degrades with increasing output power. In the confined-gain fiber laser, the beam quality is good and does not degrade with output power. Gain filtering of higher-order modes in 28 μm diameter core fiber lasers is demonstrated with a beam quality of M^2 = 1.3 at all pumping levels. Theoretical modeling is shown to agree well with experimentally observed trends.

Marciante, J R↗

All-Fiber Optical Magnetic-Field Sensor Based on Faraday Rotation in Highly Terbium-Doped Fiber

An all-fiber optical magnetic field sensor is demonstrated. It consists of a fiber Faraday rotator and a fiber polarizer. The fiber Faraday rotator uses a 2-cm-long section of 56-wt.%-terbium–doped silicate fiber with a Verdet constant of –24.5 rad/(Tm) at 1053 nm. The fiber polarizer is Corning SP1060 single-polarization fiber. The sensor has a sensitivity of 0.49 rad/T and can measure magnetic fields from 0.02 to 3.2 T.

Faraday effect↗

Effective Verdet Constant in a Terbium-Doped-Core Phosphate Fiber

The concept of an effective Verdet constant is proposed and experimentally validated. The effective Verdet constant of light propagation in a fiber includes contributions from the materials in both the core and the cladding. It is measured in a 25 wt.% terbium-doped-core phosphate fiber to be -6.2±0.4 rad/ (Tm) at 1053 nm, which is six times larger than silica fiber. The result agrees well with Faraday rotation theory in optical fiber.

Sun, L↗

Comments on "Beam Quality Factor of Higher Order Modes in a Step-Index Fiber"

In a previously published paper [1], equations are presented that predict the beam-quality factor of beams from multimode fibers. We demonstrate that the simplification made in these equations to generate several of the figures is incorrect and that these formulas cannot be generally simplified for beams that are coherent superpositions of modes. [1] H. Yoda, P. Polynkin, and M. Mansuripur, “Beam quality factor of higher order modes in a step-index fiber,” J. Lightwave Technol., vol. 24, no. 3, pp. 1350–1355, Mar. 2006.

beam quality factor↗

Gain Filtering for Single-Spatial-Mode Operation of Large-Mode-Area Fiber Amplifiers

Gain filtering of higher order modes in large-mode-area fibers is an extremely robust method for providing diffraction-limited performance regardless of core diameter or input beam quality. Analytic calculations demonstrate that reducing the diameter of the gain dopants compared to the waveguide diameter produces differential gain that is higher for the fundamental mode than all other fiber modes at all saturation levels. Matching the gain dopant to the mode profile is not as beneficial as a simple step profile since the primarymechanism of gain filtering is to deny gain toward the edge of the waveguide where most of the higher order mode power is contained. Numerical simulations of multikilowatt fiber amplifiers with up to 100-μm-diameter cores show that gain filtering is extremely robust, providing 99% of the output power in the fundamental mode output with only 90% of the seed power in the fundamental mode. Even with poor seed launch with 50% of the power in the fundamental mode, gain filtering can provide up to 90% of the output power in the fundamental mode.

fiber amplifiers↗

Pump-Induced, Dual-Frequency Switching in a Short-Cavity, Ytterbium-Doped Fiber Laser

Using a short linear cavity composed of a section of highly ytterbium-doped fiber surrounded by two fiber Bragg gratings, dual frequency switching is achieved by tuning the pump power of the laser. The dual-frequency switching is generated by the thermal effects of the absorbed pump in the ytterbium-doped fiber. At each frequency, the laser shows single-longitudinal-mode behavior. In each single-mode regime, the optical signal-to-noise ratio of the laser is greater than 50 dB. The dual-frequency, switchable, fiber laser can be designed for various applications by the careful selection of the two gratings.

Fiber Lasers↗

OMEGA EP High-Energy Petawatt Laser: Progress and Prospects

OMEGA EP (extended performance) is a petawatt-class addition to the existing 30-kJ, 60-beam OMEGA Laser Facility at the University of Rochester. It will enable high energy picosecond backlighting of high-energy-density experiments and inertial confinement fusion implosions, the investigation of advanced-ignition experiments such as fast ignition, and the exploration of high-energy-density phenomena. The OMEGA EP short-pulse beams have the flexibility to be directed to either the existing OMEGA target chamber, or the new, auxiliary OMEGA EP target chamber for independent experiments. This paper will detail progress made towards activation, which is on schedule for completion in April 2008.

Maywar, D N↗

Cryogenic Target-Implosion Experiments on OMEGA

The University of Rochester’s Laboratory for Laser Energetics has been imploding thick cryogenic targets for six years. Improvements in the Cryogenic Target Handling System and the ability to accurately design laser pulse shapes that properly time shocks and minimize electron preheat, produced high fuel areal densities in deuterium cryogenic targets (202+/-7 mg/cm^2). The areal density was inferred from the energy loss of secondary protons in the fuel (D2) shell. Targets were driven on a low final adiabat (alpha = 2) employing techniques to radially grade the adiabat (the highest adiabat at the ablation surface). The ice layer meets the target-design toughness specification for DT ice of 1-um rms (all modes), while D2 ice layers average 3.0-um-rms roughness. The implosion experiments and the improvements in the quality and understanding of cryogenic targets are presented.

Harding, D R↗