Search NASA⌕ Search

Engineering topics

Margolis, Kenneth

Publications and source records attributed to Margolis, Kenneth.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Theoretical Evaluation of the Pressures, Forces, and Moments at Hypersonic Speeds Acting on Arbitrary Bodies of Revolution Undergoing Separate and Combined Angle-of-attack and Pitching Motions

Equations based on Newtonian impact theory have been derived and a computational procedure developed with the aid of several design-type charts which enable the determination of the aerodynamic forces and moments acting on arbitrary bodies of revolution undergoing either separate or combined angle-of-attack and pitching motions. Bodies with axially increasing and decreasing cross-sectional area distributions are considered; nose shapes may be sharp, blunt, or flat faced. The analysis considers variations in angle of attack from -90 degrees to 90 degrees and allows for both positive and negative pitching rates of arbitrary magnitude. The results are also directly applicable to bodies in either separate or combined sideslip and yawing maneuvers.

Margolis, Kenneth↗
NASA NTRS1960

Theoretical Calculations of the Pressures, Forces, and Moments Due to Various Lateral Motions Acting on Tapered Sweptback Vertical Tails with Supersonic Leading and Trailing Edges

Based on expressions for the linearized velocity potentials and pressure distributions given in NACA Technical Report 1268, formulas for the span load distribution, forces, and moments are derived for families of thin isolated vertical tails with arbitrary aspect ratio, taper ratio, and sweepback performing the motions constant sideslip, steady rolling, steady yawing, and constant lateral acceleration. The range of Mach number considered corresponds, in general, to the condition that the tail leading and trailing edges are supersonic. To supplement the analytical results, design-type charts are presented which enable rapid estimation of the forces and moments (expressed as stability derivatives) for given combinations of geometry parameters and Mach number.

Margolis, Kenneth↗
NASA NTRS1959

Formulas Pertinent to the Calculation of Flow-Field Effects at Supersonic Speeds Due to Wing Thickness

Expressions based on linearized supersonic-flow theory are derived for the perturbation velocity potential in space due to wing thickness for rectangular wings with biconvex airfoil sections and for arrow, delta, and quadrilateral wings with wedge-type airfoil sections. The complete range of supersonic speeds is considered subject to a minor aspect-ratio-Mach number restriction for the rectangular plan form and to the condition that the trailing edge is supersonic for the sweptback wings. The formulas presented can be utilized in determining the induced-flow characteristics at any point in the field and are readily adaptable for either numerical computation or analytical determination of any velocity components desired.

Margolis, Kenneth↗
NASA NTRS1958

Theoretical Calculations of Supersonic Wave Drag at Zero Lift for a Particular Store Arrangement

An analysis, based on the linearized thin-airfoil theory for supersonic speeds, of the wave drag at zero lift has been carried out for a simple two-body arrangement consisting of two wedgelike surfaces, each with a rhombic lateral cross section and emanating from a common apex. Such an arrangement could be used as two stores, either embedded within or mounted below a wing, or as auxiliary bodies wherein the upper halves could be used as stores and the lower halves for bomb or missile purposes. The complete range of supersonic Mach numbers has been considered and it was found that by orienting the axes of the bodies relative to each other a given volume may be redistributed in a manner which enables the wave drag to be reduced within the lower supersonic speed range (where the leading edge is substantially subsonic). At the higher Mach numbers, the wave drag is always increased. If, in addition to a constant volume, a given maximum thickness-chord ratio is imposed, then canting the two surfaces results in higher wave drag at all Mach numbers. For purposes of comparison, analogous drag calculations for the case of two parallel winglike bodies with the same cross-sectional shapes as the canted configuration have been included. Consideration is also given to the favorable (dragwise) interference pressures acting on the blunt bases of both arrangements.

Margolis, Kenneth↗
NASA NTRS1956

Theoretical calculations of the pressure, forces, and moments at supersonic speeds due to various lateral motions acting on thin isolated vertical tails

Velocity potentials, pressure, distributions, and stability derivatives are derived by use of supersonic linearized theory for families of thin isolated vertical tails performing steady rolling, steady yawing, and constant-lateral-acceleration motions. Vertical-tail families (half-delta and rectangular plan forms) are considered for a broad Mach number range. Also considered are the vertical tail with arbitrary sweepback and taper ratio at Mach numbers for which both the leading edge and trailing edge of the tail are supersonic and the triangular vertical tail with a subsonic leading edge and a supersonic trailing edge. Expressions for potentials, pressures, and stability derivatives are tabulated.

Margolis, Kenneth↗
NASA NTRS1950

Theoretical lift and damping in roll at supersonic speeds of thin sweptback tapered wings with streamwise tips, subsonic leading edges, and supersonic trailing edges

On the basis of linearized supersonic-flow theory, generalized equations were derived and calculations made for the lift and damping in roll of a limited series of thin sweptback tapered wings. Results are applicable to wings with streamwise tips and for a range of supersonic speeds for which the wing is wholly contained between the Mach cones springing from the wing apex and from the trailing edge of the root section. A further limitation is that the tip Mach lines may not intersect on the wing. For the portion of the wing external to the Mach cones springing from the leading edge of the wing tips, the pressure distributions for lift and roll previously obtained for the triangular wing are valid. For the portion of the wing contained within the wing-tip Mach cones a satisfactory approximation to the exact pressure distribution was obtained by application of a point-source-distribution method developed in NACA-TN-1382. A series of design curves are presented which permit rapid estimation of the lift-curve slope and damping-in-roll derivative for given values of aspect ratio, taper ratio, Mach number, and leading-edge sweep. (author)

Malvestuto, Frank S , Jr↗