Engineering topics

Marichalar, J.

Publications and source records attributed to Marichalar, J..

3 records

NASA NTRS2019

Operational and Technical Updates to the Object Reentry Survival Analysis Tool

The Object Reentry Survival Analysis Tool (ORSAT) has been used in the NASA Orbital Debris Program Office for over 25 years to estimate risk due to uncontrolled reentry of spacecraft and rocket bodies. Development over the last 3 years has included: a major change to the treatment of carbon fiber- and glass fiber-reinforced plastics (CFRP and GFRP, respectively); an updated atmospheric model; a new model for computing casualty area around an impacting debris object; and a newly-implemented scheme to determine the breakup altitude of a reentry object. Software also was written to automatically perform parameter sweeps in ORSAT to allow for uncertainty quantification and sensitivity analysis for components with borderline demisability. These updates have improved the speed and fidelity of the reentry analysis performed using ORSAT, and have allowed for improved engineering understanding by estimating the uncertainty for each component’s survivability. A statistical model for initial conditions captures the latitude bias in population density, a large improvement over the previous inclination-based latitude-averaged models. A sample spacecraft has been analyzed with standard techniques using ORSAT 6.2.1 and again using all the updated models; we will demonstrate the variation in the total debris casualty area and overall expectation of casualty.

Ostrom, C.↗

NASA NTRS2012

Plume-Free Stream Interaction Heating Effects During Orion Crew Module Reentry

During reentry of the Orion Crew Module (CM), vehicle attitude control will be performed by firing reaction control system (RCS) thrusters. Simulation of RCS plumes and their interaction with the oncoming flow has been difficult for the analysis community due to the large scarf angles of the RCS thrusters and the unsteady nature of the Orion capsule backshell environments. The model for the aerothermal database has thus relied on wind tunnel test data to capture the heating effects of thruster plume interactions with the freestream. These data are only valid for the continuum flow regime of the reentry trajectory. A Direct Simulation Monte Carlo (DSMC) analysis was performed to study the vehicle heating effects that result from the RCS thruster plume interaction with the oncoming freestream flow at high altitudes during Orion CM reentry. The study was performed with the DSMC Analysis Code (DAC). The inflow boundary conditions for the jets were obtained from Data Parallel Line Relaxation (DPLR) computational fluid dynamics (CFD) solutions. Simulations were performed for the roll, yaw, pitch-up and pitch-down jets at altitudes of 105 km, 125 km and 160 km as well as vacuum conditions. For comparison purposes (see Figure 1), the freestream conditions were based on previous DAC simulations performed without active RCS to populate the aerodynamic database for the Orion CM. Other inputs to the analysis included a constant Orbital reentry velocity of 7.5 km/s and angle of attack of 160 degrees. The results of the study showed that the interaction effects decrease quickly with increasing altitude. Also, jets with highly scarfed nozzles cause more severe heating compared to the nozzles with lower scarf angles. The difficulty of performing these simulations was based on the maximum number density and the ratio of number densities between the freestream and the plume for each simulation. The lowest altitude solutions required a substantial amount of computational resources (up to 1800 processors) to simulate approximately 2 billion molecules for the refined (adapted) solutions.

Marichalar, J.↗

NASA NTRS2010

Analysis of Plume Impingement Effects from Orion Crew Service Module Dual Reaction Control System Engine Firings

Plume impingement effects on the Orion Crew Service Module (CSM) were analyzed for various dual Reaction Control System (RCS) engine firings and various configurations of the solar arrays. The study was performed using a decoupled computational fluid dynamics (CFD) and Direct Simulation Monte Carlo (DSMC) approach. This approach included a single jet plume solution for the R1E RCS engine computed with the General Aerodynamic Simulation Program (GASP) CFD code. The CFD solution was used to create an inflow surface for the DSMC solution based on the Bird continuum breakdown parameter. The DSMC solution was then used to model the dual RCS plume impingement effects on the entire CSM geometry with deployed solar arrays. However, because the continuum breakdown parameter of 0.5 could not be achieved due to geometrical constraints and because high resolution in the plume shock interaction region is desired, a focused DSMC simulation modeling only the plumes and the shock interaction region was performed. This high resolution intermediate solution was then used as the inflow to the larger DSMC solution to obtain plume impingement heating, forces, and moments on the CSM and the solar arrays for a total of 21 cases that were analyzed. The results of these simulations were used to populate the Orion CSM Aerothermal Database.

Prisbell, Andrew↗