Search NASA⌕ Search

Engineering topics

Mark G Turner

Publications and source records attributed to Mark G Turner.

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2026

Design and Optimization of an Open Rotor Stage

Open rotor propulsors enable greatly increased effective bypass ratios over current aircraft engines, resulting in significantly improved efficiencies. One of the most promising of these geometries is the “open fan”, which consists of a single rotor followed by a single stator. This configuration will be referred to as an “open rotor stage” for design work at NASA. In this work we consider the multidisciplinary design and optimization of an open rotor stage using a variety of 2D and 3D techniques. The 2D aerodynamic techniques used for design include a 2D Trefftz plane method, axisymmetric throughflow, and quasi-3D blade-to-blade CFD. Aerodynamic performance is prioritized, while structural requirements are met and some acoustic considerations are included. Between the rotor, stator, and hub profiles, a total of 101 design variables are used. Differences in the process of designing an open rotor stage vs. designing other high-speed propellers are also discussed. The current design, the NASA Optimized Propulsor for Efficiency and Noise (N-OPEN-1), achieves 84.7% net efficiency as predicted by 3D CFD, with further improvements expected to be possible. This design makes effective use of a slower rotor and a less tip-loaded work distribution than typical single-rotation propellers, allowing the stator to produce 14.8% of the thrust. Laminar flow on the blades was responsible for a 1.7% efficiency benefit and warrants further study.

turbomachinery↗
NASA NTRSDate not supplied

Gas Turbine Hybrid Technology at NASA

NASA has been instrumental in shaping the research for Gas Turbine – Electric Hybrid Technology by in-house R&D and through industry partners. The Technology Readiness Level (TRL) is being advanced so the technology will find its way into products used by the flying public as well as developing the longer-term goals. The hybrid approach leads to having the advantage of both a gas turbine and electrification in addition to using both approaches in a synergistic way. This is a panel session and the presentation will describe the basics of hybrid, and what NASA is doing for Gas Turbine Hybrid Technology.

Gas Turbine↗
NASA NTRSDate not supplied

Update on Subsonic Single Aft Engine (SUSAN) Electrofan Trade Space Exploration

NASA is conducting an ongoing trade study analysis of the SUSAN Electrofan aircraft concept, which utilizes 20-MW-class electrified aircraft propulsion to enable propulsive, aerodynamic, and control benefits while retaining the range, speed, and size of typical narrow-body regional aircraft. The study is constrained by the ground rules of operating within the current airport and airspace infrastructure. This ongoing study seeks to find a configuration and combination of technologies that yield significant fuel burn and emissions benefits. Another key goal is to reduce cost per passenger mile. Currently, the study is focused on a configuration that utilizes jet A or sustainable aviation fuels, however, we plan to consider other fuel alternatives in the future. This paper describes the progress in defining the architecture of the aircraft, engine, power system, control system, and initial understandings of the sensitivity of the potential configurations to technology assumptions based on key performance parameters. Additionally, progress towards definition and refinement of driving operational, economic, infrastructure, certification, and technical requirements is discussed.

aircraft concept↗
NASA NTRSDate not supplied

Full Stall Simulations of a Redesigned Ventilation Fan for the ISS

The concept of a stall is studied rigorously in the aerospace industry. From a design standpoint, instabilities such as stall are undesirable– operation in the stall regime has a tremendous impact on aerodynamic performance as well as structural integrity. In extreme cases, operating in stall conditions can cause failure. Further, stall can cause a loss of lift on aircraft wings or a loss of thrust in aircraft engines. In any case, stall continues to be a topic of interest in the aerospace industry. The present work aims to analyze the stall characteristics of a ventilation fan that was recently designed for the International Space Station (ISS). Although the ventilation fan has a rotor-stator design, this paper considers a rotor-only configuration. The FUN3D Computational Fluid Dynamic (CFD) solver developed by NASA Langley Research Center was used to simulate the operational characteristics of the ventilation fan. FUN3D solves the Unsteady Reynolds-Averaged Naiver-Stokes (URANS) equations using implicit time marching and a dynamic overset grid. The FUN3D solver was originally written for exterior flow fields; however, this work represents an extension of the FUN3D solver to turbomachinery or interior flow fields. The FUN3D results for the rotor-only ventilation fan accurately captured the operational characteristics inherent to compressors– the results shared similar performance trends when compared to the experimental results for the rotor-stator case. A peak adiabatic efficiency of 96% occurred at a MFR of 105.2 CFM, the minimum aerodynamically stable point. A computationally stable stall occurred at a mass flow rate of 43.8 CFM where the adiabatic efficiency dropped to 69%.

CFD↗
NASA NTRSDate not supplied

Design and Optimization of a 3-Stage Axial Supercritical CO2 Compressor

This paper presents the detailed design and optimization of a three-stage axial supercritical carbon dioxide (sCO2) compressor to support the advancement of sCO 2 power cycles, recognized for their efficiency and compactness in energy conversion. The three-stage design is a scaled model of the original nine-stage 100 MW design. The aerodynamic design and structural analysis were performed at the University of Cincinnati, and the results are presented. The first stage of the design has been meticulously manufactured and experimentally tested at University of Notre Dame Turbomachinery Laboratory. The design process starts with the preliminary design process, considering the required operating boundary conditions and geometrical constraints for full stage design. The design is then scaled down to 3-stage based on the power limitation. The definition for design parameters has been inspired from the EEE HPC design and tweaked to fit the sCO 2 operation. Axisymmetric analysis is performed next and the parametric geometry modeler -Tblade3 has been used to create 3D blade geometry from the results which can then be exported for the 3D CFD analysis and optimization. An efficiency of 89.85% is predicted for the final design at the design point.

Compressor↗
NASA NTRSDate not supplied

Turbomachinery Simulation Impact on Design, Understanding, and Optimization

This presentation shows the impact of Turbomachinery Simulation from simple analytical simulation to high fidelity CFD and Finite Element Analysis on the design of turbomachinery and the understanding of flow physics that is then used to improve design approaches. The impact of Optimization is also presented. The best approach for the tool development is to work with a compressor, fan, or turbine designer or to work on the design process directly. The presentation represents the work and impact of the author over his 45-year career and provides insight for both new and experienced engineers. The presentation explores applications of distortion from a downstream fan frame, the first uses of 3D CFD for fan, compressor and turbine design, and approaches to optimization for performance and structures.

optimization↗
NASA NTRSDate not supplied

Design and Optimization of an Open Rotor Stage

Open rotor propulsors enable greatly increased effective bypass ratios over current aircraft engines, resulting in significantly improved efficiencies. One of the most promising of these geometries is the “open fan”, which consists of a single rotor followed by a single stator. This configuration will be referred to as an “open rotor stage” for design work at NASA. In this work we consider the multidisciplinary design and optimization of an open rotor stage using a variety of 2D and 3D techniques. The 2D aerodynamic techniques used for design include a 2D Trefftz plane method, axisymmetric throughflow, and quasi-3D blade-to-blade CFD. Aerodynamic performance is prioritized, while structural requirements are met and some acoustic considerations are included. Between the rotor, stator, and hub profiles, a total of 101 design variables are used. Differences in the process of designing an open rotor stage vs. designing other high-speed propellers are also discussed. The current design, the NASA Optimized Propulsor for Efficiency and Noise (N-OPEN-1), achieves 84.7% net efficiency as predicted by 3D CFD, with further improvements expected to be possible. This design makes effective use of a slower rotor and a less tip-loaded work distribution than typical single-rotation propellers, allowing the stator to produce 14.8% of the thrust. Laminar flow on the blades was responsible for a 1.7% efficiency benefit and warrants further study.

Open rotors↗