Search NASA⌕ Search

Engineering topics

Markham, B. L.

Publications and source records attributed to Markham, B. L..

At least 37 records · Page 2

Spectral Characterization of the LANDSAT-4 MSS Sensors

Relative spectral response data for the LANDSAT-4 and LANDSAT-4 backup multispectral scanner subsystems (MSS), the protoflight and flight models are presented and compared to similar data for the LANDSAT 1, 2 and 3 scanners. Channel (six channels per band) outputs for soil and soybean targets were simulated and compared within each band and between scanners. The principal differences between the spectral responses of the LANDSAT-4 scanners and previous scanners are discussed. The simulated LANDSAT-4 scanner outputs were 3 to 10 percent lower in the red band and 3 to 11 percent higher in the first near-IR band than previous scanners for the soybeans targets. The LANDSAT-4 scanners were generally more uniform from channel to channel within bands than previous scanners. In the upper-band edge of the red band of the protoflight scanner, one channel was markedly different (12 nm) from the rest. For a soybeans target, this nonuniformity resulted in a within-band difference of 6.2 percent in simulated outputs between channels.

Markham, B. L.↗

Impact of Thematic Mapper Sensor Characteristics on Classification Accuracy

A three factor (spectral, spatial, and radiometric resolution), two level (TM and MSS) analysis of variance (ANOVA) approach allowed evaluation of the effects of each factor individually and in all possible combinations. Digital classification accuracy was used as the figure of merit. Nine study sites in Washington, D.C. each of approximately 256 x 256 TM pixels, were randomly selected from the full scene for analysis. These results strongly suggest that the quantization level improvements and the addition of new spectral bands in the visible and middle IR regions (both afforded by the TM sensor design) can result in improved capabilities to accurately delineate land cover categories using a per point Gaussian maximum likelihood classifier. On the other hand, results indicate that the increase in spatial resolution to 30m does not significantly enhance classification accuracy. The spatial result points to an inherent limitation of a per point classifier and to the need to improve data analysis techniques to handle high spatial resolution data.

Williams, D. L.↗

Quick Look Analysis of TM Data of the Washington, District of Columbia Area

A fixed factor analysis-of-variance (ANOVA) approach was used to quantify the impact of each TM sensor characteristic (spectral, spatial, and radiometric resolutions) on classification accuracy. All assessments were made relative to MSS sensor characteristics, and the impact of each characteristic was assessed individually, and in all possible combinations. Thematic Mapper data acquired over the Washington, D.C. area on November 2, 1982 were utilized to conduct the experiment. The following results were obtained: the reduction of quantization level from eight bits to six bits caused a decrease in overall accuracy (7%); the use of only three bands (TM 2, 3 and 4) covering the isible and near infrared portion of the spectrum caused a decrease in overall accuracy (7%); and the decrease in spatial resolution resulted in an increase in overall accuracy (4%). Results indicate that the increased radiometric and spectral resolution of the TM instrument do provide increased information content. The result of the spatial resolution degradation is somewhat misleading, in that the result is more a function of spatial resolution.

Williams, D. L.↗

Preliminary Comparisons of the Information Content and Utility of TM Versus MSS Data

Comparisons were made between subscenes from the first TM scene acquired of the Washington, D.C. area and a MSS scene acquired approximately one year earlier. Three types of analyses were conducted to compare TM and MSS data: a water body analysis, a principal components analysis and a spectral clustering analysis. The water body analysis compared the capability of the TM to the MSS for detecting small uniform targets. Of the 59 ponds located on aerial photographs 34 (58%) were detected by the TM with six commission errors (15%) and 13 (22%) were detected by the MSS with three commission errors (19%). The smallest water body detected by the TM was 16 meters; the smallest detected by the MSS was 40 meters. For the principal components analysis, means and covariance matrices were calculated for each subscene, and principal components images generated and characterized. In the spectral clustering comparison each scene was independently clustered and the clusters were assigned to informational classes. The preliminary comparison indicated that TM data provides enhancements over MSS in terms of (1) small target detection and (2) data dimensionality (even with 4-band data). The extra dimension, partially resultant from TM band 1, appears useful for built-up/non-built-up area separation.

Markham, B. L.↗

Characterization of the LANDSAT sensors' spatial responses

The characteristics of the thematic mapper (TM) and multispectral scanner (MSS) sensors on LANDSATs 4 and 5 affecting their spatial responses are described, and functions defining the response of the system to an arbitrary input spatial pattern are derived, i.e., transfer functions (TF) and line spread functions (LSF). These design LSF's and TF's were modified based on prelaunch component and system measurements to provide improved estimates. Prelaunch estimates of LSF/FT's are compared to in-orbit estimates. For the MSS instruments, only limited prelaunch scan direction square-wave response (SWR) data were available. Design estimates were modified by convolving in Gaussian blur till the derived LSF/TF's produced SWR's comparable to the measurements. The two MSS instruments were comparable at their temperatures of best focus; separate calculations were performed for bands 1 and 3, band 2 and band 4. The pre-sample nadir effective instantaneous field's of view (EIFOV's) based on the .5 modulation transfer function (MTF) criteria vary from 70 to 75 meters in the track direction and 79 to 82 meters in the scan direction. For the TM instruments more extensive prelaunch measurements were available. Bands 1 to 4, 5 and 7, and 6 were handled separately as were the two instruments. Derived MTF's indicate nadir pre-sample EIFOV's of 32 to 33 meter track (bands 1 to 5, 7) and 36 meter scan (bands 1 to 5, 7) and 1245 meter track (band 6) and 141 meter scan (band 6) for both TM's.

Markham, B. L.↗

A statistical evaluation of the advantages of Landsat Thematic Mapper data in comparison to Multispectral Scanner data

On July 16, 1982, the second decade of land remote sensing from space was inaugurated with the successful launch of Landsat-4. This satellite carries the Multispectral Scanner (MSS) and a new sensor, the Thematic Mapper (TM). The TM represents the result of an effort in which all of the major improvements in remote-sensing capability were simultaneously integrated into one system. An experiment was developed and conducted to quantify the effect of each TM sensor parameter on classification accuracy. This paper discusses the experimental design and summarizes the results obtained using TM data acquired over the Washington, DC area on November 2, 1982. Attention is given to a study site/data description, the experimental design, photointerpretation and digitization, spectral simulation, radiometric simulation, and spatial simulation.

Williams, D. L.↗

Spectral characterization of the LANDSAT Thematic Mapper sensors

The spectral coverage characteristics of the two thematic mapper instruments were determined by analyses of spectral measurements of the optics, filters, and detectors. The following results are presented: (1) band 2 and 3 flatness was slightly below specification, and band 7 flatness was below specification; (2) band 5 upper-band edge was higher than specifications; (3) band 2 band edges were shifted upward about 9 nm relative to nominal; and (4) band 4, 5, and 7 lower band edges were 16 to 18 nm higher then nominal.

Markham, B. L.↗

Diffusive-convective vapor transport across horizontal and inclined rectangular enclosures

The enhancement of vapor transport across horizontal and inclined rectangular (two-dimensional) enclosures by expansive convection is studied numerically for a range in Grashof number that extends up to boundary layer flow. Comparison is made with predictions of the simplifying model and resulting analytical treatment of Klosse and Ullersma (1973) for various aspect ratios of the enclosure. The influence of varying Schmidt and Prandtl numbers is investigated. Solutions for interfacial (growth) flux and temperature distributions are given, showing practically important nonuniformities.

Markham, B. L.↗

Spectral characterization of the Landsat-4 MSS sensors

Two multispectral scanner subsystems (MSS) have been fabricated and tested by an American aerospace company for the NASA Landsat program. One MSS, designated the protoflight (PF) model, was integrated into the Landsat-4 spacecraft, which was launched on July 16, 1982. The second, designated the flight (F) model, has been integrated into the Landsat-4 backup satellite, which is scheduled for possible launch in 1985. Each MSS has four bands in the reflective portion of the electromagnetic spectrum. The engineering test data which were collected included channel-by-channel spectral response curves. A description of the test procedure is included in Appendix A. This document is to make available to the Landsat user community data on the spectral characteristics of the two sensors. The Landsat-4 PF and F scanners were found to be essentially identical in mean spectral response.

Markham, B. L.↗

Spectral characterization of the LANDSAT-4 thematic mapper sensors

Data collected on the spectral characteristics of the LANDSAT-4 and LANDSAT-4 backup thematic mapper instruments, the protoflight (PF) and flight (F) models, respectively are analyzed and summarized. Tests were conducted on the instruments and their components to determine compliance with two sets of spectral specifications: Band-by-band spectral coverage and channel-by-channel within-band spectral matching.

Markham, B. L.↗

Spectral characterization of the LANDSAT thematic mapper sensors

Data collected on the spectral characteristics of the LANDSAT-4 and LANDSAT-4 backup thematic mapper instruments, the protoflight (TM/PF) and flight (TM/F) models, respectively, are presented and analyzed. Tests were conducted on the instruments and their components to determine compliance with two sets of spectral specifications: band-by-band spectral coverage and channel-by-channel within-band spectral matching. Spectral coverage specifications were placed on: (1) band edges--points at 50% of peak response, (2) band edge slopes--steepness of rise and fall-off of response, (3) spectral flatness--evenness of response between edges, and (4) spurious system response--ratio of out-of-band response to in-band response. Compliance with the spectral coverage specifications was determined by analysis of spectral measurements on the individual components contributing to the overall spectral response: filters, detectors, and optical surfaces.

Markham, B. L.↗

Preliminary evaluation of thematic mapper sensor characteristics relative to land cover/land use discrimination

Preliminary experimental results of airborne thematic mapper (TM) data taken to quantify the effect of three major TM sensor parameters, spectral, spatial, and radiometric resolution, six months after launch of Landsat-4 are reported. The flight took place on Nov. 2, 1982 over Washington, D.C., and data gathered were compared with ground reference data from color airborne photography on a 1:40,000 scale. Analyses proceeded by deleting one band from each of four data sets, thus making the data equivalent to MSS data. Attention was directed to land cover/use classes in a quick-look format. A per-pixel maximum likelihood scheme was found to increase the recognition and dicrimination categorization capabilities. Finer spatial resolution, however, impeded classification due to increased within-class variability of the field-center pixels, which also incresed class overlap in the spectral data base. Improved data analyses techniques are therefore needed to exploit the available higher spatial resolution of the TM.

Williams, D. L.↗

Impact of thematic mapper sensor characteristics on classification accuracy

A three factor (spectral, spatial, and radiometric resolution), two level (TM and MSS) analysis of variance (ANOVA) approach allowed evaluation of the effects of each factor individually and in all possible combinations. Digital classification accuracy was used as the figure of merit. Nine study sites in Washington, DC, each of approximately 256 x 256 TM pixels, were randomly selected from the full scene for analysis. These results strongly suggest that the quantization level improvements and the addition of new spectral bands in the visible and middle IR regions (both afforded by the TM sensor design) can result in improved capabilities to accurately delineate land cover categories using a per point Gaussian maximum likelihood classifier. On the other hand, results indicate that the increase in spatial resolution to 30 m does not significantly enhance classification accuracy. The spatial result points to an inherent limitation of a per point classifier and to the need to improve data analysis techniques to handle high spatial resolution data.

Williams, D. L.↗

Spectral characterization of the LANDSAT-D multispectral scanner subsystems

Relative spectral response data for the multispectral scanner subsystems (MSS) to be flown on LANDSAT-D and LANDSAT-D backup, the protoflight and flight models, respectively, are presented and compared to similar data for the Landsat 1,2, and 3 subsystems. Channel-bychannel (six channels per band) outputs for soil and soybean targets were simulated and compared within each band and between scanners. The two LANDSAT-D scanners proved to be nearly identical in mean spectral response, but they exhibited some differences from the previous MSS's. Principal differences between the spectral responses of the D-scanners and previous scanners were: (1) a mean upper-band edge in the green band of 606 nm compared to previous means of 593 to 598 nm; (2) an average upper-band edge of 697 nm in the red band compared to previous averages of 701 to 710 nm; and (3) an average bandpass for the first near-IR band of 702-814 nm compared to a range of 693-793 to 697-802 nm for previous scanners. These differences caused the simulated D-scanner outputs to be 3 to 10 percent lower in the red band and 3 to 11 percent higher in the first near-IR band than previous scanners for the soybeans target. Otherwise, outputs from soil and soybean targets were only slightly affected. The D-scanners were generally more uniform from channel to channel within bands than previous scanners.

Markham, B. L.↗

Temporal spectral response of a corn canopy

Techniques developed for the prediction of winter wheat yields from remotely sensed data indicating crop status over the growing season are tested for their applicability to corn. Ground-based spectral measurements in the Landsat Thematic Mapper bands 3 (0.62-0.69 microns), 4 (0.76-0.90 microns) and 5 (1.55-1.75 microns) were performed at one-week intervals throughout the growing season for 24 plots of corn, and analyzed to derive spectral ratios and normalized spectral differences of the IR and shortwave IR bands with the red. The ratios of the near IR and shortwave IR bands are found to provide the highest and most consistent correlations with corn yield and dry matter accumulation, however the value of band 5 could not be tested due to the absence of water stress conditions. Integration of spectral ratios over several dates improved the correlations over those of any single date by achieving a seasonal, rather than instantaneous, estimate of crop status. Results point to the desirability of further tests under other growth conditions to determine whether satellite-derived data will be useful in providing corn yield information.

Markham, B. L.↗

Temporal relationships between spectral response and agronomic variables of a corn canopy

Attention is given to an experiment in which spectral radiance data collected in three spectral regions are related to corn canopy variables. The study extends the work of Tucker et al. (1979) in that more detailed measurements of corn canopy variables were made using quantitative techniques. Wet and dry green leaf biomass is considered along with the green leaf area index, chlorotic leaf biomass, chlorotic leaf area, and leaf water content. In addition, spectral data were collected with a hand-held radiometer having Landsat-D Thematic Mapper (TM) bands TM3 (0.63-0.69 micrometers), TM4 (0.76-0.90 micrometers), and TM5 (1.55-1.75 micrometers). TM3, TM4, and TM5 seem to be well situated spectrally for making remotely sensed measurements related to chlorophyll concentration, leaf density, and leaf water content.

Kimes, D. S.↗

Numerical modeling of diffusive physical vapor transport in cylindrical ampoules

Diffusion limited physical vapor transport in closed cylindrical ampoules of aspect ratio (length/radius) between 0.5 and 10 was studied numerically. The transport of a crystal forming component A through an inert component B, which undergoes zero net transport, was considered. A case in which the partial pressure of B is comparable to that of A, as well as systems with very low partial pressures of B (impurity cases) were treated. Concentrations and velocity distributions were obtained from the coupled transport equations for momentum, mass and components. It was found that the interdiffusion of components in viscous interaction with the container walls leads to (1) recirculation of component B, even in the absence of gravity; (2) concentration gradients normal to the main transport direction in the vapor space; and (3) non-uniform interfacial concentration gradients and, hence, non-uniform crystal growth rates.

Greenwell, D. W.↗