Search NASA⌕ Search

Engineering topics

Maroni, Victor A.

Publications and source records attributed to Maroni, Victor A..

At least 19 records

Cathode active materials for lithium-ion batteries

Compounds, powders, and cathode active materials that can be used in lithium ion batteries are described herein. Methods of making such compounds, powders, and cathode active materials are described.

Wu, Huiming↗

Beneficial Effect of Li 5 FeO 4 Lithium Source for Li-Ion Batteries with a Layered NMC Cathode and Si Anode

The energy density of lithium-ion batteries can be increased by replacing the traditional graphite anode with a high capacity silicon anode. However, volume changes and interfacial instabilities cause a large irreversible capacity and a continual loss of lithium during cycling, which lead to rapid capacity loss. In this work, we add Li 5 FeO 4 (LFO) to a LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC) cathode as a pre-lithiation additive, which increases the lithium inventory and extends the cycle life of Si-graphite/NMC full cells, and decreases the NMC particle degradation. LFO delivers a large 764 mAh g –1 LFO capacity below 4.7 V vs Li/Li + . By tuning the LFO content in Si-graphite/LFO-NMC full cells, we show higher capacity, improved retention, lower impedance, and superior rate performance compared to full cells without LFO. Post-test characterizations demonstrate that LFO inclusion in the cathode matrix leads to less NMC secondary particle segregation/cracking and a thinner surface reduced layer on the NMC particles. The beneficial effects of LFO endure after the lithium reserve has been exhausted, highlighting a lasting synergy between the lithium source and electrode active materials. This study introduces a new approach to simultaneously increase lithium inventory and reduce cathode degradation, and makes critical advances toward enabling Si anodes for lithium-ion batteries.

25 ENERGY STORAGE↗

Photo-accelerated fast charging of lithium-ion batteries

Due to their exceptional high energy density, lithium-ion batteries are of central importance in many modern electrical devices. A serious limitation, however, is the slow charging rate used to obtain the full capacity. Thus far, there have been no ways to increase the charging rate without losses in energy density and electrochemical performance. Here we show that the charging rate of a cathode can be dramatically increased via interaction with white light. We find that a direct exposure of light to an operating LiMn 2 O 4 cathode during charging leads to a remarkable lowering of the battery charging time by a factor of two or more. This enhancement is enabled by the induction of a microsecond long-lived charge separated state, consisting of Mn 4+ (hole) plus electron. This results in more oxidized metal centers and ejected lithium ions are created under light and with voltage bias. We anticipate that this discovery could pave the way to the development of new fast recharging battery technologies.

25 ENERGY STORAGE↗

Cathode active materials for lithium-ion batteries

Compounds, powders, and cathode active materials that can be used in lithium ion batteries are described herein. Methods of making such compounds, powders, and cathode active materials are described.

Wu, Huiming↗

Lithium Acetylide: A Spectroscopic Marker for Lithium Deposition During Fast Charging of Li-Ion Cells

Rapid charging of lithium-ion batteries being developed for electric vehicles is a formidable challenge. Electrochemical polarization of cells during fast charging favors deposition of metallic Li onto the surface of the graphite electrode, and this Li plating compromises safety and accelerates performance degradation. Observing the onset of Li nucleation is essential for elucidation of mechanisms and defining conditions favoring this Li plating, but presently available methods are not sufficiently sensitive and selective while also allowing satisfactory spatial resolution. We demonstrate the use of Raman spectroscopy as a sensitive means to identify Li nucleation and map Li deposition. Metallic Li is detected indirectly by probing the vibrations in an acetylide species (represented as Li—C≡C—X) that is formed on the exposed surface of Li nuclei in contact with the solid electrolyte interphase on graphite. Surface-enhanced Raman scattering (SERS) involving this species on Li nuclei appears to dramatically increase sensitivity and selectivity of this detection, making our method an excellent complement to the existing spectroscopy and microscopy approaches for determining Li deposition.

25 ENERGY STORAGE↗

Cathode active materials for lithium-ion batteries

Compounds, powders, and cathode active materials that can be used in lithium ion batteries are described herein. Methods of making such compounds, powders, and cathode active materials are described.

25 ENERGY STORAGE↗

Composition and Impedance Heterogeneity in Oxide Electrode Cross-Sections Detected by Raman Spectroscopy

Lithium-bearing layered transition metal oxides are the materials of choice for positive electrodes in high energy lithium-ion cells being developed for electric vehicle applications. During electrochemical cycling, the loss of mobile lithium-ions due to undesirable side reactions and an increase in cell resistance leads to a decline in the energy and power performance of the cells. This performance loss is often non-uniform across multiple cells, especially for those cycled at high voltages and at high C-rates. This non-uniformity results from inhomogeneous behavior in the battery electrodes, which can lead to localized areas that deteriorate faster than the neighboring regions. Raman spectroscopy is among the many advanced techniques that have been used to probe inhomogeneity in electrode behavior. Typically, Raman spectroscopy of lithium-ion cell electrodes are conducted in the top-down mode, and at-best provide an incomplete, surface biased account of electrode behavior. In contrast, micro-Raman measurements conducted on ion-milled electrode cross-sections provide information from regions that span the full thickness of the electrode. Here, spectroscopy data from pristine, aged, and relithiated/aged positive electrodes are reported. In conclusion, the spectral differences between oxide particles near the top-surface and particles deeper into the aged electrodes highlight a clearly defined non-uniform behavior during cell aging.

36 MATERIALS SCIENCE↗

Investigations of Si Thin Films as Anode of Lithium-Ion Batteries

Amorphous silicon thin films having various thicknesses were investigated as a negative electrode material for lithium-ion batteries. Electrochemical characterization of the 20 nm thick thin silicon film revealed a very low first cycle Coulombic efficiency, which can be attributed to the silicon oxide layer formed on both the surface of the as-deposited Si thin film and the interface between the Si and the substrate. Among the investigated films, the 100 nm Si thin film demonstrated the best performance in terms of first cycle efficiency and cycle life. Observations from scanning electron microscopy demonstrated that the generation of cracks was inevitable in the cycled Si thin films, even as the thickness of the film was as little as 20 nm, which was not predicted by previous modeling work. However, the cycling performance of the 20 and 100 nm silicon thin films was not detrimentally affected by these cracks. Lastly, the poor capacity retention of the 1 mu m silicon thin film was attributed to the delamination.

25 ENERGY STORAGE↗

Enabling the high capacity of lithium-rich anti-fluorite lithium iron oxide by simultaneous anionic and cationic redox

Anionic redox reactions in cathodes of lithium-ion batteries are allowing opportunities to double or even triple the energy density. However, it is still challenging to develop a cathode, especially with Earth-abundant elements, that enables anionic redox activity for real-world applications, primarily due to limited strategies to intercept the oxygenates from further irreversible oxidation to O 2 gas. Here in this paper, we report simultaneous iron and oxygen redox activity in a Li-rich anti-fluorite Li 5 FeO 4 electrode. During the removal of the first two Li ions, the oxidation potential of O 2- is lowered to approximately 3.5 V versus Li + /Li 0 , at which potential the cationic oxidation occurs concurrently. These anionic and cationic redox reactions show high reversibility without any obvious O 2 gas release. Furthermore, this study provides an insightful guide to designing high-capacity cathodes with reversible oxygen redox activity by simply introducing oxygen ions that are exclusively coordinated by Li + .

25 ENERGY STORAGE↗

Enhanced Raman Scattering from NCM523 Cathodes Coated with Electrochemically Deposited Gold

Materials with the general composition LiMO2, where M is a mix of nickel, cobalt, and manganese, have been studied extensively as cathodes for lithium-based electrochemical cells. Some compositions, like LiNi0.5Co0.2Mn0.3O2 (NCM523), have already found application in commercial lithium-ion batteries. Pre-test and post-test analyses of these types of cathodes have benefited greatly from the use of Raman spectroscopy. Specifically, Raman spectroscopy can be used to investigate the phonons of the LiMO2 lattice. This is particularly useful for studies of the LiMO2 after it has been formed into the type of polymer-bonded laminate from which typical battery cathodes are cut. One of the problems that occurs in such studies is that the scattering from the LiMO2 phase gets progressively weaker as the nickel content increases. NCM523 poses one example of this behavior owing to the fact that half of the transition metal content is nickel. In this study we show that the intensity of the Raman scattering from the NCM523 phonons can be significantly increased by electroplating clusters of sub-micron gold particles on NCM523-containing laminate structures. The gold appears to plate somewhat selectively on the NCM523 particles in randomly sized clusters. These clusters stimulate the Raman scattering from the NCM523 to varying extents that can reach nearly 100 times the scattering intensity from uncoated pristine laminates.

cathode↗

A new strategy to mitigate the initial capacity loss of lithium ion batteries

Hard carbon (non-graphitizable) and related materials, like tin, tin oxide, silicon, and silicon oxide, have a high theoretical lithium delivery capacity (>550 mAh/g depending on their structural and chemical properties) but unfortunately they also exhibit a large initial capacity loss (ICL) that overrides the true reversible capacity in a full cell. Overcoming the large ICL of hard carbon in a full-cell lithium-ion battery (LIB) necessitates a new strategy wherein a sacrificial lithium source additive, such as, Li5FeO4 (LFO), is inserted on the cathode side. Full batteries using hard carbon coupled with LFO-LiCoO2 (LCO) are currently under development at our laboratory. We find that the reversible capacity of a cathode containing LFO can be increased by 14%. Furthermore, the cycle performance of full cells with LFO additive is improved from <90% to >95%. We show that the LFO additive not only can address the irreversible capacity loss of the anode, but can also provide the additional lithium ion source required to mitigate the lithium loss caused by side reactions. In addition, we have explored the possibility to achieve higher capacity with hard carbon, whereby the energy density of full cells can be increased from ca. 300 Wh/kg to >400 Wh/kg.

hard carbon↗

Direct graphene growth on (111) Cu2O templates with atomic Cu surface layer

This work explores nucleation and epitaxy of graphene on crystalline Cu2O templates formed via self assembly and surface reduction of Cu2O nanocrystallites on the cubic textured (100) orientation Cu (CTO-Cu) and polycrystalline Cu (poly-Cu) substrates, respectively. It has been found that the presence of sub-surface oxygen causes the reconstruction of Cu surface due to the formation of oriented Cu2O nanocrystallites at a low H2 gas flow. Self-assembly of the Cu2O nanocrystallites into a textured surface template provides direct nucleation sites for graphene growth after the oxygen-sublattice on the template surface is reduced. The atomic Cu surface layer provides advantages of high graphene growth rate due to the catalytic role of Cu and in-plane alignment of graphene nuclei. It is particularly important that the Cu2O crystallites have predominantly (111) orientation aligned to each other in the plane of the (100) CTO-Cu substrates, which allows epitaxy of graphene with much lower defect density as compared to that in the poly-Cu case. Since Cu2O (111) templates may be developed on lattice matched (100) surfaces of other dielectric materials, this self-assembly approach provides a promising pathway for large-scale, transfer free graphene epitaxy on nonmetallic surfaces.

Liu, Jianwei↗

The synthesis of ternary acetylides with tellurium: Li 2 TeC 2 and Na 2 TeC 2

The synthesis of ternary acetylides Li 2 TeC 2 and Na 2 TeC 2 is presented as the first example of ternary acetylides with metalloid elements instead of transition metals. The synthesis was carried out by the direct reaction of the corresponding bialkali acetylides with tellurium powder in liquid ammonia. Alternatively, the synthesis of Na 2 TeC 2 was also carried out by the direct reaction of tellurium powder and two equivalents of NaC 2 H in liquid ammonia leading to Na 2 TeC 2 and acetylene gas through an equilibrium containing the assumed NaTeC 2 H molecules besides the reactants and the products. The resulting disordered crystalline materials were characterized by X-ray diffraction and Raman spectroscopy. Implications of these new syntheses on the synthesis of other ternary acetylides with metalloid elements and transition metals are also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Novel tri-modal defect structure in Nb-doped MOCVD YBa2Cu3O7: A paradigm for pinning landscape control

Immobilization of vortices, or flux pinning, is both an enduring scientific issue and one of the most important problems in optimizing high temperature superconductors (HTS) for commercial use. Here, we demonstrate a practical approach to the creation of a multi-modal flux pinning landscape in YBa2Cu3O7 (YBCO) films employing an industrially scalable metal organic chemical vapor deposition technique. Through controlled additions of Nb, we have achieved a novel distribution of crystallographic defects that immobilize (pin) vortices in the YBCO matrix. That is, with only the addition of a single dopant element, a tri-modal defect structure that threads through the YBCO matrix laterally (parallel to the ab planes of YBCO), vertically (parallel to the YBCO c-axis), and isotropically in the form of random spherical defects is induced. For optimally doped samples, the influence of these multi-modal nanocrystalline defect structures on the flux pinning properties manifests itself as a superior improvement in the critical current density (Jc) for all magnetic field orientations. The results demonstrate the possibility of achieving an ideal flux pinning landscape (from an orientation and strength viewpoint), which permits the design of HTS wires with fully-tuneable properties by processes suitable for large-scale manufacturing.

Aytug, Tolga↗

Examination of Through-Thickness/Through-Time Phase Evolution during an MOD-Type REBCO Precursor Conversion Using Raman Microsscopy

Through-thickness/through-time composition analyses were made on REBa{sub 2}Cu{sub 3}O{sub 6+x} (REBCO) films prepared from metal-organic deposited (MOD) precursors on a RABiTS (rolling-assisted biaxially textured substrate) template. Y Dy{sub 0.5}Ba{sub 2}Cu{sub 3}O{sub 6 + x} films were fabricated either by a single precursor coating or by two separate, equivalent precursor coatings with an intermediate decomposition. Specimens were quenched at selected times along a heat treatment profile that simulated conditions used by American Superconductor, then examined by Raman microscopy along mechanically milled slopes through the REBCO films. Upon reaching the reaction temperature TR, the precursor initially transforms into a (Y, Dy){sub 2}Cu{sub 2}O{sub 5}, CuO, Cu{sub 2}O, and RE-Ba-F-O phase mix, and this is followed shortly by substrate level REBCO formation that propagates upwards through time. Our results indicate that (1) the single layer (SL) and double layer (DL) films (both {approx} 1.2 {mu}m thick) react to completion at about the same rate and arrive at a similar final composition and (2) some residual Ba-Cu-O phases persist near the top of the fully reacted films. The performance of the SL film was moderately better than that of the DL film, seemingly due to better through-thickness REBCO texture as determined using x-ray diffraction.

36 MATERIALS SCIENCE↗