Search NASA⌕ Search

Engineering topics

Marquez Rossy, Andres

Publications and source records attributed to Marquez Rossy, Andres.

Mitigation of hydrogen crossover in liquid alkaline water electrolysers using gas recombination catalysts

The rising demand for hydrogen calls for improvements in the efficiency of liquid alkaline water electrolysers (LAWEs), which can be fulfilled by advanced electrodes or separators. Nevertheless, they also intensify hydrogen crossover and safety concerns, thus mandating efficient mitigation strategies. Here we studied the correlation between cathodes and hydrogen crossover behaviours and mitigated safety risks by designing a gas recombination catalyst (GRC). We attribute the elevated hydrogen crossover associated with platinum-based cathodes to their preferential utilization for the hydrogen evolution reaction that creates elevated hydrogen supersaturation, as evidenced by direct measurements of dissolved hydrogen concentration. Varying the placement of platinum layers relative to the cathode–separator interface also supports this conclusion. The implementation of a GRC reduces hydrogen crossover by 95% without affecting LAWE performance and functions for over 1,000 h at 1 A cm−2. This study provides insights into hydrogen supersaturation and the crossover mechanism, as well as offering a promising pathway to enhance the efficiency and reliability of alkaline water electrolysis.

Liu, Haotian↗

Process–Property–Performance Mapping of Additively Manufactured 316H Stainless Steel Components

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development of advanced materials and components fabricated via additive manufacturing, and is using laser powder bed fusion (LPBF) of 316H stainless steel as an initial case study. In the previous fiscal year, miniature high-throughput specimens were printed on multiple LPBF systems to provide initial processing windows to minimize porosity and limit epitaxial grain growth during prints. This fiscal year, scaled builds were completed on three different LPBF systems at ORNL: a GE Concept Laser M2, a Renishaw AM400, and an EOS M290. Builds on the Concept Laser were conducted on multiple powder lots and processing parameter ranges to provide microstructure effects on time-independent and time-dependent mechanical properties. Builds on the Renishaw were produced using Oak Ridge National Laboratory (ORNL)-optimized printing parameters and Argonne National Laboratory (ANL)-optimized printing parameters to compare outcomes of parallel process optimization efforts at different national laboratories on the same LPBF system. Similarly, the build completed on the EOS M290 replicated the processing parameters of builds completed at Los Alamos National Laboratory (LANL). Optical microscopy and electron backscatter diffraction characterization was completed on all builds. In addition to the general round robin characterization, this work-package generated time-independent data, including tensile and fracture toughness test data on scaled Concept Laser builds as a function of processing parameters and post-build heat treatment. This analysis is complimentary to work in parallel work packages aiming to establish heat treatment and processing effects on time-dependent properties. It was found that although the stress-relief heat treatment provides the highest strength at lower-temperatures, tensile strength begins to converge at higher temperatures regardless of heat treatment condition. In addition, the more rigorous solution annealing and hot-isostatic pressing post-build heat treatments result in higher fracture toughness than the stress-relieved condition. The root-causes of the lower fracture toughness of the stress-relieved LPBF 316H material was informed via a stress-relief optimization study on a scaled concept laser print, where it was found that although dislocation recovery was largely complete after only a couple hours at 650°C, the extended hold of the current 24h heat treatment employed on scaled builds likely caused increased carbide volume fractions along the LPBF 316H grain boundaries, thereby deteriorating crack propagation resistance. This trend was seen to become more deleterious with additional increases of stress-relief temperature to 750°C or 850°C. These results have helped inform a new optimal stress-relief annealing condition for LPBF 316H for future campaign testing (650°C for 2h).

36 MATERIALS SCIENCE↗

Considering interplay between multiple physical phenomena to elucidate single crystal-like texture, phase transformations, and mechanical behavior of directed energy deposited SS316L

A widespread implementation of large scale additive manufacturing (AM) processes, such as wire arc-directed energy deposition (WA-DED) AM can transform the current manufacturing supply chain networks. Naturally, such implementation requires control of the microstructural attributes, such as texture and phase evolution in the processed alloys. Currently, the texture evolution in fusion-based AM (F-BAM) processes is majorly rationalized by the phenomena occurring only during solidification. However, such rationalization is insufficient for understanding the evolution of primary and secondary crystallographic orientations, and consequently, fails to offer a comprehensive understanding and control of overall texture in F-BAM processed alloys. To this end, we report a single crystal (SX)-like texture in WA-DED processed SS316L for the first time. Furthermore, we assess the physical phenomena that may lead to such unique microstructural evolution during WA-DED AM. Subsequently, using microstructural characterization spanning the build height and thermomechanical simulations we investigate the effect of competitive growth and epitaxial growth occurring during solidification and thermally induced plastic deformation occurring post solidification on the overall texture of WA-DED processed SS316L. A spatial variation in solidification pathway is also established and correlated with variation in undercoolings across the build. Tensile tests revealed a strong orientation dependence of deformation mechanisms with over 110% elongation to failure of specimens deformed along <011>. Such anisotropy is rationalized using Schmid's analysis of dislocation slip and deformation twinning. Importantly, overall, the mechanisms outlined in this work will facilitate an enhanced understanding and subsequent control of texture evolution, solidification behavior and mechanical behavior of WA-DED processed steels.

36 MATERIALS SCIENCE↗

A Co-Registered In-Situ and Ex-Situ Dataset from a Laser Powder Bed Fusion Additive Manufacturing Process (Peregrine v2023-10)

This release contains a co-registered in-situ and ex-situ Peregrine dataset from a single Concept Laser M2 Laser Powder Bed Fusion (L-PBF) stainless steel 316L build. These data were collected at the Manufacturing Demonstration Facility (MDF) located at Oak Ridge National Laboratory (ORNL). The dataset includes layer-wise visible-light in-situ imaging data, the laser scan paths and parameters, in-situ temporal sensor data, X-Ray Computed Tomography (X-CT) scans, pycnometry and tensile test results, etched micrographs from selected locations, and the target part geometries. Additionally, anomaly detections produced by a modified Dynamic Segmentation Convolutional Neural Network (DSCNN) are provided.

36 MATERIALS SCIENCE↗

Report Outlining Computed Tomography Strategy and Microscopy Approach to Qualifying AM 316 Materials

This report is part of work package CR-22OR0406012, Automated, High-Throughput Materials Characterization Techniques , under the Advanced Materials and Manufacturing Technologies program (AMMT). The project’s primary objective is to leverage our AI-based rapid and high-throughput automated characterization framework to qualify additively manufactured 316 materials comprehensively, focusing on optimizing the additive manufacturing process and evaluating the performance of 3D-printed stainless steel components. This report outlines our strategy for leveraging the automated characterization process for qualifying 316H materials.

36 MATERIALS SCIENCE↗

Microstructure and high temperature properties of tungsten processed via electron beam melting additive manufacturing

There is considerable interest in the adoption of additive manufacturing for processing refractory metals. The layer-wise fabrication approach enables opportunities for producing complex geometries which cannot be otherwise be achieved via powder metallurgy. However, the processing science is still in its nascent stages and structure–property relations are relatively unexplored. Fundamental research is needed to further develop the technology and enable the fabrication of refractory metals for high temperature applications. Here we focus on the processing of pure tungsten using electron beam melting additive manufacturing. Experimentally we develop a suitable processing window for achieving high density crack free material. Microstructural analysis reveals that the microstructure generally consists of a columnar structure with a (111) build direction fiber preference, although, fiber switching was observed. Process induced deformation is believed to drive the formation of subgrains whose boundaries exhibit a high dislocation density. Additionally, high temperature tensile testing reveals that the material exhibits excellent properties closer to that of annealed tungsten. Significant mechanical anisotropy was observed to be present which is likely driven by strong crystallographic texture.

36 MATERIALS SCIENCE↗

Multi material/functionally graded wire arc additive manufacturing of high strength steel valves clad with nickel alloy 625 used for oil extraction

This Phase 1 technical collaboration project (ORNL/TM-2022/2683) began on August 1st, 2020 and concluded on July 31st, 2022. The collaboration partner Schlumberger is a large business enterprise assisting oil companies to extract oil from land and subsea cost competitively and safely. It is based in Houston, Texas USA. In this work as study of additive deposition of AWS EF100S-G and AWS ERNiCrMo-3 wires via wire-arc process was conducted.

36 MATERIALS SCIENCE↗

Creep behavior of $\gamma$-TiAl fabricated via electron beam additive manufacturing

$\gamma$-TiAl is a desirable structural engineering alloy with excellent high temperature specific strength. This material system has been shown to be processable at industrial scales via additive manufacturing. In this work we investigate the microstructure and properties of Ti48Al2Cr2Nb fabricated via electron beam melting. No significant anisotropy was observed from during creep testing under the considered conditions. Creep deformation resistance and rupture strength are comparable to material synthesized via traditional routes.

Fernandez-Zelaia, Patxi↗

Statistical Estimation of Strain Using Spatial Correlation Functions

Ex-situ estimation of strains from deformed micrographs is not possible as there are no persistent features which can be tracked. Two point spatial statistics enable the rigorous quantification of spatial patterns in heterogeneous media. In this paper, we propose a novel method for estimating strains directly from dissimilar micrographs using a continuum mechanics approach. Rather than operating directly on images from sequential frames, as is done in digital image correlation, we operate on different microstructure realizations. This is made possible by comparing the spatial autocorrelation maps of deformed and undeformed micrographs rather than direct comparison of images. Additionally, a Bayesian framework is proposed for quantifying uncertainty. We first illustrate the efficacy of this method on speckle pattern images from digital image correlation experiments. Then, we demonstrate that the method is capable of operating on dissimilar micrographs using deformed synthetic binary microstructures. Finally, we present a case study on polycrystalline additively manufactured 316L deformed via tension. The proposed method works well and we discuss implications and limitations of the presented work.

36 MATERIALS SCIENCE↗

Nickel-based superalloy single crystals fabricated via electron beam melting

Additive manufacturing technologies have emerged as potential disruptive processes whose possible impacts range from supply chain logistics, prototyping, and novel materials synthesis. Numerous works illustrate the ability to control mi- crostructure in fusion based processes and a few recent authors have even produced single crystals. However, a number of open questions remain regarding the process window which enables printing of single crystals. Furthermore, it has been observed that these additively manufactured single crystals exhibit a preferred $\langle$011$\rangle$ secondary orientation. In this work we investigate fabrication conditions which enable printing of single crystals via electron beam melting. A space filling design of experiments is utilized to efficiently explore the fabrication space. Single crystals were success- fully obtained using both commercially available powders and custom melt alloys. Microstructures obtained via these exploratory experiments exhibited a continuum of columnar structures ranging from weakly textured polycrystals, near single crystal, and fully single crystalline material. Complex geometry experiments are performed to study the grain selection mechanism. We find that the grain selection mechanism is independent of the bulk scale geometry and must therefore by driven by local heat transfer and solidification dynamics. Furthermore, grain selection is shown to be driven by competing driving forces; one which prefers epitaxial growth and another which is driven by the imposed scan pattern geometry. Finally, a mechanism is proposed for the anomalous secondary orientation preference.

36 MATERIALS SCIENCE↗

Electron Beam Powder Bed Fusion Additive Manufacturing of Refractory Metals

The processing of refractory metals via additive manufacturing (AM) presents an opportunity to fabricatecomponents not possible through traditional powder metallurgy techniques. However, processing via AM isextremely challenging and there exist a host of technological limitations still unaddressed. Molybdenumand tungsten are two materials of particular interest for nuclear energy generation applications. Themajority of existing work on the processing of these materials is focused on laser powder bed fusion whereasa smaller body of work exists for electron beam melting AM. In general, material with acceptable densitycan be obtained via both routes however cracking is much more difficult to mitigate against. Strongcrystallographic fiber textures have been observed across a range of refractory systems. In this work wepresent our recent findings on electron beam melting AM of pure tungsten and molybdenum. Wedemonstrate that defect-free material can be obtained in both systems with appropriate processing. Strongbuild direction crystallographic texture fibers are observed in both systems. In molybdenum the fibertexture has direct impact on the resulting tensile behavior. These results demonstrate that electron beamAM is a suitable technology for processing these difficult to fabricate materials.

Fernandez-Zelaia, Patxi↗

Architecture and properties of TCR fuel form

The fuel form developed for the Transformational Challenge Reactor demonstration program leverages recent advances in manufacturing, materials, and computational sciences, delivering a new architecture for production of high-performance microencapsulated nuclear fuels. The fuel consists of conventionally manufactured uranium nitride tristructural isotropic fuel particles embedded inside a 3D-printed silicon carbide matrix. Finally, this paper describes the overall architecture and manufacturing process for this fuel form, its properties and behavior, and the ongoing development activities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure and properties of a high temperature Al–Ce–Mn alloy produced by additive manufacturing

An Al–10Ce-8Mn (wt%) alloy was designed and fabricated by laser powder bed fusion additive manufacturing (AM). The rapid cooling rates of the AM process produced a refined microstructure with a large fraction of reinforcing intermetallic phases. The tensile properties of the alloy were characterized in the as-fabricated state and following thermal exposure. The properties of the as-fabricated microstructure showed exceptional high-temperature performance and strength retention at elevated temperatures up to 400 °C relative to benchmark wrought Al and AM Al alloy properties. Characterization of the microstructure and thermodynamic modeling of the ternary Al–Ce–Mn system rationalized the solidification and solid-state phase transformations. Finally, analysis of the relevant strengthening mechanisms for both the as-fabricated and thermally exposed conditions was performed.

36 MATERIALS SCIENCE↗

Cryo-quenched Fe–Ni–Cr alloy decorative steel single crystals II: Alloy phases, structure, hardness, tensile, tribological, magnetic and electronic properties

We have previously reported (Boatner et al., J. Alloys Compd. 691 (2017) 666–671) on the discovery, formation, processing, and application of a new decorative ternary steel alloy and on its use in a wide range of practical applications including: custom and commercial knives, art objects, jewelry, electronics, and furniture. This decorative property results when polished single crystals of the 70 wt%Fe-15 wt%Ni-15 wt% Cr austenitic alloy are cryo-quenched into the martensitic phase resulting in the formation of a three-dimensional raised pattern of mixed austenitic/martensitic laths. These laths propagate across large dimensions of the material due to the absence of grain boundaries in the single crystal. The macroscopic optically reflective 3-D decorative pattern reproduces the structural symmetry inherent in the single-crystal orientation. This pattern results solely from the metallurgical phase properties of the ternary alloy and is completely distinct from the properties of Damascus steels or more modern so-called pattern-welded steels. Here we use X-ray diffraction, nanoindentation, hardness measurements/scratch testing, tribological measurements, and alloy resistivity and magnetization methods to obtain a more fundamental and comprehensive study of the effects of the austenitic/martensitic phase transition on the structural and physical properties of the 70 wt%Fe-15 wt%Ni-15 wt% Cr alloy. These results reveal new insight into irreversible phenomena that are associated with the inhibited phase transition on heating of the two-phase, mixed austenitic/martensitic structure that is formed subsequent to cryo-quenching the alloy crystal to 77 K.

36 MATERIALS SCIENCE↗

Development of a new generation of quench and partitioning steels: Influence of processing parameters on texture, nanoindentation, and mechanical properties

A novel quenching and partitioning process (Q&P) including the hot stamping (HS) process was studied, using two stamping temperatures (750 °C and 800 °C) and two quenching temperatures (318 °C and 328 °C). This combination is here called Hot Stamping and Quenching and Partitioning process (HSQ&P). The partitioning step was performed at 400 °C for 100 s in all cycles. Microstructural features were comprehensively studied using electron backscattered diffraction and nanoindentation techniques. HSQ&P samples showed a good combination of ductility and high-strength due to the presence of: retained austenite, inter-critical ferrite with low stored internal strain energy, grain refinement via DIFT-effect (deformation induced ferrite transformation), martensite, and bainite. Significant internal stress relief was caused by carbon partitioning, which was induced by the DIFT-effect and the partitioning stage. This also led to a considerable stored energy, which was characterized by the Kernel average dislocation and geometrically necessary dislocation analysis. In addition, predominant {110}//strain direction crystallographic texture was identified, which promotes slip deformation and enhances the mechanical properties. Moreover, remarkable amounts of fine film-like retained austenite oriented along compact crystallographic directions (i.e., $\langle$111$\rangle$ and $\langle$112$\rangle$) were observed. Finally, subsize tensile test verified the optimum mechanical behavior of HSQ&P specimens.

36 MATERIALS SCIENCE↗

Handbook of Advanced Manufactured Material Properties From TCR Structure Builds at ORNL (FY2019)

There is growing interest in the use of additive manufacturing techniques for the production and deployment of components for nuclear power applications. Specifically, the Transformational Challenge Reactor (TRC) program seeks to demonstrate the application of advanced manufacturing to rapidly develop and deploy a microreactor. As part of the TCR objective, a database on materials performance, such as thermophysical properties and mechanical performance, is required to help inform nuclear reactor designers, operators, and regulators regarding possible material limitations using emerging manufacturing techniques. The following report seeks to collect all available data regarding the material performance of candidate alloys and manufacturing processes pursued within the TCR program at Oak Ridge National Laboratory. At this time, this database focuses only on materials derived within the program and does not extend to additional manufacturing processes, manufacturers, or other advanced materials. Where appropriate, recommendations for applications of the data are provided and current knowledge gaps are identified.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗