Search NASA⌕ Search

Engineering topics

Marshall, Paul

Publications and source records attributed to Marshall, Paul.

At least 19 records

Rate constants and third-body collision efficiencies for recombination of Na with OH and O2: Implications for flame inhibition by alkali salts

Flame inhibition by alkali metals has implications for solid fuel combustion, fire safety, and a number of industrial processes. While the mechanism of inhibition is fairly well understood, details related to thermodynamic properties and rate constants are still in question. In the present work, the recombination of Na with OH (R5) and O2 (R7), respectively, was characterized theoretically, and the implications for modeling laminar premixed hydrogen flames doped with sodium species were examined. Third-body collision efficiencies and low-pressure-limit rate constants were obtained using newly fitted ab initio-based potential energy surfaces, classical trajectories, and one-dimensional master equation calculations. The results are consistent with available experimental results and aid in the present modeling study by providing rate information for bath gases and conditions that remain unexplored experimentally. Chemical kinetic modeling of relative Na and absolute H and OH profiles in H2-fueled laminar, premixed flames doped with a sodium salt shows that the most important radical removal cycle is the sequence Na + OH (+M) → NaOH (+M) (R5), NaOH + H → Na + H2O (R12), even under oxidizing conditions. A secondary cycle, Na + O2 (+M) ⇄ NaO2 (+M) (R7), NaO2 + OH → NaOH + O2 (R14), is less important due to the low thermal stability of NaO2. In most flames, reaction R7 is partially equilibrated, and reaction R14 becomes rate-limiting for the second cycle. The flame analysis supports a lower value of k14 than indicated by recent work on KO2 + OH, but more work is required to confirm this.

Jasper, Ahren W.↗

Re-Examination of the N 2 O + O Reaction

The reaction of N 2 O with O is a key step in consumption of nitrous oxide in thermal processes. It has two product channels, NO + NO (R2) and N 2 + O 2 (R3). The rate constant for R2 has been measured both in the forward and the reverse direction at elevated temperature and is well established. However, the rate constant for the N 2 + O 2 channel (R3) has been difficult to quantify and has significant error limits. Here, the direct reaction on the triplet surface has a barrier of around 40 kcal mol –1 , and it is too slow for the N 2 + O 2 channel to have any practical significance. Recently, Pham and Lin (2022) suggested an alternative low activation energy reaction path that involves intersystem crossing and reaction on the singlet surface. In the present work, we re-examined a wide range of experiments relevant for the N 2 O + O reaction through kinetic modeling, paying attention to the impact of artifacts such as impurities and surface reactions. Experimental results from shock tubes and batch reactors on the final NO yield in N 2 O decomposition, covering temperatures of 973–2200 K and pressures of 0.013–11.5 atm, support k 3 ~ 0, consistent with the high activation energy for reaction on the triplet surface and a low probability of ISC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Probing High-Temperature Amine Chemistry: Is the Reaction NH 3 + NH 2 ⇌ N 2 H 3 + H 2 Important?

The reaction NH 3 + NH 2 ⇌ N 2 H 3 + H 2 (R1) has been identified as a key step to explain experimental results for pyrolysis and oxidation of ammonia. However, no direct experimental or theoretical evidence for the reaction has been reported. In the present work, the reaction was studied by ab initio theory and by reinterpretation of experimental data. We could not locate a transition state for R1 occurring as a direct process, but alternative mechanisms yielded an upper bound to k 1 of 1.5 × 10 13 exp(–58.9 kcal mol –1 /RT) cm 3 mol –1 s –1 over 1000–2500 K, several orders of magnitude lower than values applied in modeling. Consistent with the theoretical work, re-evaluation of NH 3 pyrolysis data supported a very low value of k 1 . However, this finding opens up a novel unresolved issue. Current kinetic models cannot capture the NH 3 oxidation behavior in a number of laminar flow reactor and jet-stirred reactor experiments without adopting an improbably high value for k 1 . Furthermore, important oxidation steps might be underestimated or missing from mechanisms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Re-evaluation of rate constants for the reaction N 2 H 4 (+ M) $^→_←$ NH 2 + NH 2 (+ M)

Rate constants for the dissociation/recombination reaction N 2 H 4 (+ M) $^→_←$ NH 2 + NH 2 (+ M) are determined by a combination of quantum-chemical calculations and statistical unimolecular rate theory. Between 1100 and 2500 K, limiting low-pressure rate constants for hydrazine dissociation in the bath gas Ar of k 0 = [Ar] 6.1 × 10 20 (T/1000 K) –7.3 exp (-34490 K/T) cm 3 mol –1 s –1 , limiting high-pressure rate constants of k ∞ = 7.6 × 10 16 (T/1000 K) –1.0 exp(-33600 K/T) s –1 , and center broadening factors of the falloff curves (between 1100 and 1600 K in Ar) of F cent = 0.71 exp(- T/1460 K) + 0.29 exp(- T/21 K) + exp(-13400 K/T) were calculated. Using equilibrium constants K C = 1.7 × 10 3 (T/1000 K) –1.5 exp(-33,460 K/T) mol cm –3 , between 300 and 600 K limiting low-pressure rate constants for the reverse recombination of NH 2 radicals in the bath gas N 2 of k rec,0 = [N 2 ] 4.4 × 10 20 (T/400 K) –6.9 exp (-1630 K/T) cm 6 mol –2 s –1 , limiting high-pressure rate constants of k rec,∞ = 4.4 × 10 13 (T/1000 K) 0.44 exp(-140 K/T) cm 3 mol -1 s –1 , and center broadening factors (between 300 and 600 K in N 2 ) of F cent = exp(- T/1130 K) + exp (-10340 K/T) were obtained. A comparison with experimental results for hydrazine dissociation from the literature suggests incomplete falloff extrapolations toward k ∞ and experimental problems in the determination of k 0 at temperatures above about 1600 K. Finally, implications of the present re-evaluated rate constants for the modeling of high temperature ammonia oxidation kinetics are discussed, showing an only small influence of their precise values on the overall properties of the process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reactions of hydrazine with the amidogen radical and atomic hydrogen

The rate coefficient k 1 for NH 2 + N 2 H 4 was measured to be (5.4 ± 0.4) × 10 –14 cm 3 molecule –1 s –1 at 296 K. NH 2 was generated by pulsed laser photolysis of NH 3 at 193 nm, and monitored as a function of time by pulsed laser-induced fluorescence excited at 570.3 nm under pseudo-first order conditions in the presence of excess N 2 H 4 in an Ar bath gas. This reaction was also investigated computationally, with geometries and scaled frequencies obtained with M06-2X/6-311+G(2df,2p) theory, and single-point energies from CCSD(T)-F12b/cc-pVTZ-F12 theory, plus a term to correct approximately for electron correlation through CCSDT(Q). Three connected transition states are involved and rate constants were obtained via Multistructural Improved Canonical Variational Transition State Theory with Small Curvature Tunneling. Combination of experiment and theory leads to a recommended rate coefficient for hydrogen abstraction of k 1 = 6.3 × 10 –23 T 3.44 exp(+289 K/T) cm 3 molecule –1 s –1 . The minor channel for H + N 2 H 4 forming NH 2 + NH 3 was characterized computationally as well, to yield 5.0 × 10 –19 T 2.07 exp(-4032 K/T) cm 3 molecule –1 s –1 . Finally, these results are compared to several discordant prior estimates, and are employed in an overall mechanism to compare with measurements of half-lives of hydrazine in a shock tube.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental and modeling study of water time histories during H 2 S-N 2 O combustion in a shock tube

Here, with the interest in directly burning sour gas in gas turbines, and the fact that even small amounts of H 2 S or its combustion products can alter combustion characteristics, many research studies have been performed to better understand the combustion chemistry of H 2 S. In the present study, the water formation was followed by laser absorption with N 2 O as an oxidant, instead of O 2 . Nitrous Oxide being essentially consumed via N 2 O (+M) ⇌ N 2 + O (+M), the water formation via the H 2 S + O route can then be probed to further validate the models. Three H 2 S/N 2 O mixtures diluted in 98% Ar were studied to cover the following range of equivalence ratios: 0.5, 1.0, and 2.0, over a wide range of temperatures (1580–1940 K) around atmospheric pressure. A chemical kinetic model was then developed first by validating the base N 2 O kinetics mechanism, then by investigating the experimental results presented herein. The N 2 O kinetics mechanism was updated with recent work on the low- and high-pressure limits for N 2 O decomposition (N 2 O (+M) ⇌ N 2 + O (+M)) as well as a review of rate coefficients for N 2 O + H ⇌ N 2 + OH from the literature. Good agreement is shown for H 2 /N 2 O mixtures. Updates were then made to the H 2 S kinetics mechanism, specifically, an update from the literature on SO 2 + H (+M) ⇌ SO + OH (+M) and an adjustment to SO + SH ⇌ S 2 + OH. Additionally, reactions between SH and N 2 O were determined using W1BD data and transition state theory which required the addition of an NNS sub-mechanism. With these updates, the mechanism provides good agreement with the H 2 S/N 2 O experiments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Experimental and computational studies of the kinetics of the reaction of hydrogen peroxide with the amidogen radical

In this work, the pulsed-laser photolysis/laser-induced fluorescence method is used to study the kinetics of the reaction of NH 2 with H 2 O 2 to yield a second-order rate constant of (2.42 ± 0.55) × 10 –14 cm 3 molecule –1 s –1 at 412 K in 10–22 mbar of Ar bath gas. There are no prior measurements for comparison. To check this value and enable reliable extrapolation to other temperatures, we also compute thermal rate constants for this process over the temperature range 298–3000 K via multi-structural canonical variational transition-state theory with small-curvature multidimensional tunneling (MS-CVT/SCT). The CVT/SCT rate constants are derived using a dual-level direct dynamics approach utilizing single-point CCSD(T)-F12b/cc-pVQZ-F12 energies—corrected for core-valence and scalar relativistic effects—and M06-2X/MG3S geometries, gradients, and Hessians—for all stationary and non-stationary points along the reaction path. The multistructural method with torsional anharmonicity, based on a coupled torsional potential, is then employed to calculate correction factors for the rate constants, accounting for the comprehensive effects of torsional anharmonicity on the kinetics of this reaction system. The final MS-CVT/SCT rate constants are found to be in good agreement with our measurements and can be expressed in modified Arrhenius form as 2.13 × 10 –15 (T/298 K) 4.02 exp(–513 K/T) cm 3 molecule –1 s –1 over the temperature range of 298–3000 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An experimental and modeling study on auto-ignition kinetics of ammonia/methanol mixtures at intermediate temperature and high pressure

A rapid compression machine (RCM) has been applied to measure the ignition delay times of NH 3 /CH 3 OH mixtures covering pressures of 20 and 40 bar, equivalence ratios of 0.5, 1.0 and 2.0, and temperatures between 845 and 1100 K. Here the measurements show that the NH 3 /CH 3 OH mixtures become more reactive with increasing methanol addition. Addition of merely 1% (molar basis) of CH 3 OH to NH 3 lowers the ignition temperature around 100 K at 40 bar in comparison to pure NH 3 . The ignition delay is a complex function of fuel mixture and stoichiometry. For the 1% CH 3 OH mixture, the leaner mixtures are more reactive, while the reverse trend is found for mixtures with 5%, 20% and pure CH 3 OH. Analysis of the pressure profiles shows three distinct ignition modes for NH 3/ CH 3 OH mixtures, facilitated by the pre-ignition heat release from NH 3 consumption. A detailed mechanism for ignition of NH 3 /CH 3 OH fuel blends has been developed, capable of reproducing the ignition behavior of mixtures with reasonable accuracy. A subset for amine / methanol interactions was established, with rate constants for the key reaction between NH 2 and CH 3 OH calculated from ab initio theory. A sensitivity analysis indicates that the critical reactions during the auto-ignition process vary with the CH 3 OH mole fraction in the fuel. The ammonia chemistry, namely NH 2 + NO, NH2 + NO 2 and NH 2 + HO 2 , is dominant for the mixture with 1% CH 3 OH, while the reactions related to CH 3 OH and H 2 O 2 are more important for the 20% CH 3 OH mixture. The interaction between ammonia and methanol shows a more prominent effect on auto-ignition for mixtures with 5% CH 3 OH in fuel as compared to those with 1% and 20% CH 3 OH. According to the modeling results, methanol addition is found to enrich the O/H radical pool, consuming ammonia and promoting auto-ignition through different reaction pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Challenges in Kinetic modeling of ammonia pyrolysis

Ammonia pyrolysis reactions have implications for its ignition and oxidation in engines and gas turbines. In the present work, the chemistry of ammonia pyrolysis is investigated by kinetic modeling and theory. Rate constants for key reactions are carefully evaluated based on available experimental and theoretical results. The high pressure limit k1,∞ for NH 2 + H (+M) ⇄ NH 3 (+M) (R1) is calculated to be essentially the collision frequency, indicating that dissociation of ammonia in combustion processes will be at or close to the low pressure limit even at engine and gas turbine conditions. The chemical kinetic model is validated against reported shock tube measurements of NH 3 , NH 2 , and NH in ammonia pyrolysis. Predictions are in good agreement with observations for dilute conditions (≤ 0.5% NH 3 ), but the model appears to underpredict the NH 3 consumption rate at longer times in less dilute mixtures. At short reaction times, thermal dissociation of NH3, together with the NH 3 + H reaction, controls conversion. At longer times, secondary reactions involving NH 2 and NH become important due to their impact on the radical pool. Predictions become sensitive to formation and consumption of diazene (tHNNH and cHNNH). Several of the key steps in the ammonia pyrolysis mechanism are radical-radical reactions that are difficult to measure accurately and challenging to calculate theoretically, and a more comprehensive experimental characterization is desirable to support further model development.

10 SYNTHETIC FUELS↗

New reactions of diazene and related species for modelling combustion of amine fuels

Potential energy surfaces for reactions involving N 2 H 2 isomers of diazene (diimide) have been explored using density functional theory, with energies based on coupled-cluster theory. A focus is on processes that create or consume these species, and isomerisation between the E (trans) and Z (cis) forms of HNNH. Furthermore, these include isomerisation and dissociation pathways for HNNH, addition of H atoms to form N 2 H 3 , abstraction by H atoms yielding short-lived NNH, and abstraction reactions of H with N 2 H 3 . Transition state and capture theories are applied for high-pressure-limiting behaviour, while low-pressure and falloff regions are characterised via the methods of Troe and coworkers. Rate constants and thermochemistry are provided to improve models of diamine chemistry, relevant to the combustion of NH 3 especially at high concentrations, high pressures or under reducing conditions. Results indicate that amine radical recombination mainly yields the E HNNH isomer, while H-abstraction from N 2 H 3 results in E HNNH and H 2 NN. However, at elevated temperature E → Z isomerisation becomes competitive, and Z HNNH, being more reactive, acts to enhance the diazene consumption rate.

10 SYNTHETIC FUELS↗

Ignition delay times of NH 3 /DME blends at high pressure and low DME fraction: RCM experiments and simulations

Here, autoignition delay times of ammonia/dimethyl ether (NH 3 /DME) mixtures were measured in a rapid compression machine with DME fractions of 0, 2 and 5 and 100% in the fuel. The measurements were performed at equivalence ratios $\varphi$= 0.5, 1.0 and 2.0 and pressures in the range 10–70 bar; depending on the fuel composition, the temperatures after compression varied from 610 K to 1180 K. Admixture of DME is seen to have a dramatic effect on the ignition delay time, effectively shifting the curves of ignition delay vs. temperature to lower temperatures, up to ~250 K compared to pure ammonia. Two-stage ignition is observed at $\varphi$= 1.0 and 2.0 with 2% and 5% DME in the fuel, despite the pressure being higher than that at which pure DME shows two-stage ignition. At $\varphi$= 0.5, a reproducible pre-ignition pressure rise is observed for both DME fractions, which is not observed in the pure fuel components. A novel NH 3 /DME mechanism was developed, including modifications in the NH 3 subset and addition of the NH 2 + CH 3 OCH 3 reaction, with rate coefficients calculated from ab initio theory. Simulations faithfully reproduce the observed pre- ignition pressure rise. While the mechanism also exhibits two-stage ignition for NH 3 /DME mixtures, both qualitative and quantitative improvement is recommended. The overall ignition delay times for ammonia/DME mixtures are predicted well, generally being within 50% of the experimental values, although reduced performance is observed for pure ammonia at $\varphi$= 2.0. Simulating the ignition process, we observe that the DME is oxidized much more rapidly than ammonia. Analysis of the mechanism indicates that this ‘early DME oxidation’ generates reactive species that initiate the oxidation of ammonia, which in turn begins heat release that raises the temperature and accelerates the oxidation process towards ignition. The reaction path analysis shows that the low-temperature chain-branching reactions of DME are important in the early oxidation of the fuel, while the sensitivity analysis indicates that several reactions in the oxidation of DME, including cross reactions between DME and NH 3 species presented here, are critical to ignition, even at fractions of 2% DME in the fuel.

10 SYNTHETIC FUELS↗

Oxidation of methylamine

A detailed chemical kinetic model for oxidation of methylamine has been developed, based on theoretical work and a critical evaluation of data from the literature. In this work, the rate coefficients for the reactions of CH 3 NH 2 + O 2 → CH 2 NH 2 / CH 3 NH + HO 2 , CH 3 NH 2 + H → CH 3 + NH 3 , CH 3 NH → CH 2 NH 2 , and CH 3 NH + O 2 → CH 2 NH + HO 2 were calculated from ab initio theory. The mechanism was validated against experimental results from batch reactors, flow reactors, shock tubes, and premixed flames. The model predicts satisfactorily explosion limits for CH 3 NH 2 and its oxidation in a flow reactor. However, oxidation in the presence of nitric oxide, which strongly promotes reaction at lower temperatures, is only described qualitatively. Furthermore, calculated flame speeds are higher than reported experimental values; the model does not capture the inhibiting effect of the NH 2 group in CH 3 NH 2 compared to CH 4 . More work is desirable to confirm the products of the CH 3 NH + NO reaction and to look into possible pathways to NH 3 in methylamine oxidation.

10 SYNTHETIC FUELS↗

Experimental and theoretical studies of the reactions of ground-state sulfur atoms with hydrogen and deuterium

The gas-phase kinetics of S( 3 P) atoms with H 2 and D 2 have been studied via the laser flash photolysis—resonance fluorescence technique. S atoms were generated by pulsed photolysis of CS 2 at 193 nm and monitored by time-resolved fluorescence at 181 nm. The rate coefficients for H 2 ( k 1 ) and D 2 ( k 2 ), respectively, are summarized as k 1 (600-1110 K) = 3.0 × 10 –9 exp(– 1.317×10 5 –2.703×10 7 K/ T / 8.314 T/K ) cm 3 molecule –1 s –1 and k 2 (770-1110 K) = 2.2 × 10 –14 ( T /298 K) 3.55 exp(–5420 K/T) cm 3 molecule –1 s –1 . Error limits are discussed in the text. The rate coefficients for formation of SH(SD) + H(D) on a newly developed triplet potential energy surface were characterized via ring polymer molecular dynamics and canonical variational transition-state theory. Furthermore there is excellent agreement above about 1000 K between theory and experiment. At lower temperatures, the experimental rate coefficient is substantially larger than the results computed for the adiabatic reaction, suggesting a significant role for intersystem crossing to the singlet potential energy surface at lower temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Single Particle Damage Events in Candidate Star Camera Sensors

This viewgraph presentation presents information on the following topics: 1) Solar and trapped protons and shielding; 2) Proton interactions in Si; 3) Displacement damage effects in detectors; 4) Hot pixel mechanisms, introduction rates, and annealing.

Marshall, Paul↗

Single Particle Damage Events in Candidate Star Camera Sensors

Si charge coupled devices (CCDs) are currently the preeminent detector in star cameras as well as in the near ultraviolet (uv) to visible wavelength region for astronomical observations in space and in earth-observing space missions. Unfortunately, the performance of CCDs is permanently degraded by total ionizing dose (TID) and displacement damage effects. TID produces threshold voltage shifts on the CCD gates and displacement damage reduces the charge transfer efficiency (CTE), increases the dark current, produces dark current nonuniformities and creates random telegraph noise in individual pixels. In addition to these long term effects, cosmic ray and trapped proton transients also interfere with device operation on orbit. In the present paper, we investigate the dark current behavior of CCDs - in particular the formation and annealing of hot pixels. Such pixels degrade the ability of a CCD to perform science and also can present problems to the performance of star camera functions (especially if their numbers are not correctly anticipated). To date, most dark current radiation studies have been performed by irradiating the CCDs at room temperature but this can result in a significantly optimistic picture of the hot pixel count. We know from the Hubble Space Telescope (HST) that high dark current pixels (so-called hot pixels or hot spikes) accumulate as a function of time on orbit. For example, the HST Advanced Camera for Surveys/Wide Field Camera instrument performs monthly anneals despite the loss of observational time, in order to partially anneal the hot pixels. Note that the fact that significant reduction in hot pixel populations occurs for room temperature anneals is not presently understood since none of the commonly expected defects in Si (e.g. divacancy, E center, and A-center) anneal at such a low temperature. A HST Wide Field Camera 3 (WFC3) CCD manufactured by E2V was irradiated while operating at -83C and the dark current studied as a function of temperature while the CCD was warmed to a sequence of temperatures up to a maximum of +30C. The device was then cooled back down to -83 and re-measured. Hot pixel populations were tracked during the warm-up and cool-down. Hot pixel annealing began below 40C and the anneal process was largely completed before the detector reached +3OC. There was no apparent sharp temperature dependence in the annealing. Although a large fraction of the hot pixels fell below the threshold to be counted as a hot pixel, they nevertheless remained warmer than the remaining population. The details of the mechanism for the formation and annealing of hot pixels is not presently understood, but it appears likely that hot pixels are associated with displacement damage occurring in high electric field regions.

Marshall, Paul↗

Comparison of the Proton-Induced Dark Current and Charge Transfer Efficiency Responses of N- and P-Channel CCDs

The proton-induced CTE behavior for the Lawrence Berkeley National Laboratory (LBNL) p-CCD (being developed for the Supernovae Acceleration Project (SNAP) and Hubble Space Telescope (HST) Wide Field Camera 3 (WFC3) n-CCDs were compared using 55Fe, EPER and FPR techniques. CTE performance of the p-CCD is about an order of magnitude better after a 63 MeV fluence of 2.5 x 10(sup 9)/sq cm, which is equivalent to 2.5 years in the shielded HST orbit. Notched n- and p-CCDs yielded factor of two improvement in CTE performance as compared to their un-notched versions. The introduction rate of hot pixels was greater in p-CCD as compared to n-CCD, and also greater in notched than un-notched devices.

Marshall, Cheryl↗