Engineering topics

Martin, R. M.

Publications and source records attributed to Martin, R. M..

At least 19 records

DOE OSTI2021

Absence of long-range magnetic order in Fe 1–δ Te 2 (δ ≈ 0.1) crystals

Transition metal dichalcogenides attract considerable attention due to variety of interesting properties, including long range magnetism in nanocrystals. Here we have investigated magnetic, thermal and electrical properties of FeTe 2 single crystal with iron vacancy defects. Magnetic measurements shows paramagnetic state and the absence of magnetic order with small anisotropy in magnetic susceptibility. Fe 3d orbitals are well hybridized, contributing to bad metal electrical resistivity. Observed thermal conductivity values below room temperature are rather low and comparable to high performance thermoelectric materials. Furthermore, our results indicate that FeTe 2 can form in highly defective marcasite crystal structure which can be exploited in future materials design.

36 MATERIALS SCIENCE↗

NASA NTRS1994

Recent studies of rotorcraft blade-vortex interaction noise

Recent results are presented from several research efforts aimed at the understanding of rotorcraft blade-vortex interaction (BVI) in terms of the noise generation, directivity, and control. The results are based on work performed by NASA Langley Research Center researchers, both alone and in collaboration with other research organizations. Based on analysis of a simplified physical model, the critical parameters controlling BVI noise generation have been identified. The detailed mapping of the acoustic radiation field of a model rotor in a wind tunnel has revealed the extreme sensitivity of directivity to rotor advance ratio and disk attitude. The control and reduction of BVI noise through the use of higher harmonic pitch control is discussed.

BLADE VORTEX INTERACTION↗

NASA NTRS1990

Wake Geometry Effects on Rotor Blade-Vortex Interaction Noise Directivity

Acoustic measurements from a model rotor wind tunnel test are presented which show that the directionality of rotor blade vortex interaction (BVI) noise is strongly dependent on the rotor advance ratio and disk attitude. A rotor free wake analysis is used to show that the general locus of interactions on the rotor disk is also strongly dependent on advance ratio and disk attitude. A comparison of the changing directionality of the BVI noise with changes in the interaction locations shows that the strongest noise radiation occurs in the direction of motion normal to the blade span at the time of interaction, for both advancing and retreating side BVI. For advancing side interactions, the BVI radiation angle down from the tip-path plane appears relatively insensitive to rotor operating condition and is typically between 40 and 55 deg below the disk. However, the azimuthal radiation direction shows a clear trend with descent speed, moving towards the right of the flight path with increasing descent speed. The movement of the strongest radiation direction is attributed to the movement of the interaction locations on the rotor disk with increasing descent speed.

Martin, R. M.↗

NASA NTRS1990

Rotorcraft blade/vortex interaction noise - Its generation, radiation, and control

Recent results are presented from several research efforts aimed at the understanding of rotorcraft blade-vortex interaction noise generation, directivity, and control. The results are based on work performed by researches at the NASA Langley Research Center, both alone and in collaboration with other research organizations. Based on analysis of a simplified physical model, the critical parameters controlling the noise generation are identified. Detailed mapping of the acoustic radiation field reveals the extreme sensitivity of directivity to rotor advance ratio and disk attitude. A means of controlling blade-vortex interaction noise by higher harmonic pitch control is discussed.

Preisser, J. S.↗

NASA NTRS1989

Acoustic test of a model rotor and tail rotor: Results for the isolated rotors and combined configuration

Acoustic data from a model scale main rotor and tail rotor experiment in the NASA Langley 14 by 22 Foot Subsonic Tunnel are presented for the main rotor and trail rotor in isolation and for the two rotors operating together. Results for the isolated main rotor show the importance of the rotor flapping conditions on mid-frequency noise content. High levels of main rotor retreating side blade-vortex interaction noise are shown to radiate downstream of the model. The isolated tail rotor noise results show the dominance of harmonic noise in the thrusting direction. The occurrence of tail rotor broadband noise is seen by the broadening of the tail rotor harmonics and is attributed to fuselage wake turbulence. The combined main and tail rotor data are presented to show the dominance of each rotor's different noise sources at different directivity locations.

Martin, R. M.↗

NASA NTRS1988

Advancing-side directivity and retreating-side interactions of model rotor blade-vortex interaction noise

Acoustic data are presented from a 40 percent scale model of the four-bladed BO-105 helicopter main rotor, tested in a large aerodynamic wind tunnel. Rotor blade-vortex interaction (BVI) noise data in the low-speed flight range were acquired using a traversing in-flow microphone array. Acoustic results presented are used to assess the acoustic far field of BVI noise, to map the directivity and temporal characteristics of BVI impulsive noise, and to show the existence of retreating-side BVI signals. The characterics of the acoustic radiation patterns, which can often be strongly focused, are found to be very dependent on rotor operating condition. The acoustic signals exhibit multiple blade-vortex interactions per blade with broad impulsive content at lower speeds, while at higher speeds, they exhibit fewer interactions per blade, with much sharper, higher amplitude acoustic signals. Moderate-amplitude BVI acoustic signals measured under the aft retreating quadrant of the rotor are shown to originate from the retreating side of the rotor.

Martin, R. M.↗

NASA NTRS1987

Correlation of helicopter impulsive noise from blade-vortex interaction with rotor mean inflow

Data from a test made in the Langley 4 x 7 Meter Tunnel were parametrically studied with respect to the occurrence of blade-vortex interaction (BVI) as a function of tunnel speed and rotor angle of attack. Three microphones on the tunnel centerline forward of the model and one microphone forward and 45 degrees to the right provided the data. The rotor model was tested with a set of high-twist blades (-10 degrees) and a set of low-twist blades (-5 degrees) over the midspeed range (50 to 80 knots) at angles of attack ranging from -6 degrees (shallow climb) to 10 degrees (steep descent). The data from all four microphones indicated that the most probable time of occurrence of BVI is when the rotor descent is approximately equal to the rotor mean inflow velocity. However, some of the data showed no conclusive relationship to the mean inflow velocity.

Connor, Andrew B.↗

NASA NTRS1986

Wind-tunnel acoustic results of two rotor models with several tip designs

A three-phase research program has been undertaken to study the acoustic signals due to the aerodynamic interaction of rotorcraft main rotors and tail rotors. During the first phase, two different rotor models with several interchangeable tips were tested in the Langley 4- by 7-Meter Tunnel on the U.S. Army rotor model system. An extensive acoustic data base was acquired, with special emphasis on blade-vortex interaction (BVI) noise. The details of the experimental procedure, acoustic data acquisition, and reduction are documented. The overall sound pressure level (OASPL) of the high-twist rotor systems is relatively insensitive to flight speed but generally increases with rotor tip-path-plane angle. The OASPL of the high-twist rotors is dominated by acoustic energy in the low-frequency harmonics. The OASPL of the low-twist rotor systems shows more dependence on flight speed than the high-twist rotors, in addition to being quite sensitive to tip-path-plane angle. An integrated band-limited sound pressure level, limited by 500 to 3000 Hz, is a useful metric to quantify the occurrence of BVI noise. The OASPL of the low-twist rotors is strongly influenced by the band-limited sound levels, indicating that the blade-vortex impulsive noise is a dominant noise source for this rotor design. The midfrequency acoustic levels for both rotors show a very strong dependence on rotor tip-path-plane angle. The tip-path-plane angle at which the maximum midfrequency sound level occurs consistently decreases with increasing flight speed. The maximum midfrequency sound level measured at a given location is constant regardless of the flight speed.

Martin, R. M.↗

NASA NTRS1986

Power cepstrum technique with application to model helicopter acoustic data

The application of the power cepstrum to measured helicopter-rotor acoustic data is investigated. A previously applied correction to the reconstructed spectrum is shown to be incorrect. For an exact echoed signal, the amplitude of the cepstrum echo spike at the delay time is linearly related to the echo relative amplitude in the time domain. If the measured spectrum is not entirely from the source signal, the cepstrum will not yield the desired echo characteristics and a cepstral aliasing may occur because of the effective sample rate in the frequency domain. The spectral analysis bandwidth must be less than one-half the echo ripple frequency or cepstral aliasing can occur. The power cepstrum editing technique is a useful tool for removing some of the contamination because of acoustic reflections from measured rotor acoustic spectra. The cepstrum editing yields an improved estimate of the free field spectrum, but the correction process is limited by the lack of accurate knowledge of the echo transfer function. An alternate procedure, which does not require cepstral editing, is proposed which allows the complete correction of a contaminated spectrum through use of both the transfer function and delay time of the echo process.

Martin, R. M.↗

NASA NTRS1986

Reduction of Vane Noise in Wind-Tunnel Nozzles

Vane-induced noise reduced by adhering thin layer of porous material such as foam to downwind surface of vanes, particularly near sharp trailing edges, to prevent occurrence of edge tones. Other modifications made to aerodynamically streamline vane structure were rounding leading edges and smoothly fairing trailing edges. Boundary layer trip applied to leading edge to prevent laminar tone shedding from trailing edge.

Martin, R. M.↗

NASA NTRS1986

Application of the cepstrum to remove echoes from rotor acoustic spectra

The application of the power cepstrum technique to the analysis of model scale helicopter rotor noise spectra is investigated. The power cepstrum technique emerges as a useful tool for the removal of undesired acoustic reflections from measured rotor spectra. It is most effective when the reflections are exact duplicates of the signal, i.e., when the echo transfer function is linear. Moreover, the technique is best applied to a measured spectrum which is due entirely to the signal and its echoes, when no nonsource related signals are present. It is noted that this technique can be applied without prior knowledge of the echo characteristics.

Martin, R. M.↗

NASA NTRS1985

Reduction of background noise induced by wind tunnel jet exit vanes

The NASA-Langley 4 x 7 m wind tunnel develops low frequency flow pulsations at certain velocity ranges during open throat mode operation, affecting the aerodynamics of the flow and degrading the resulting model test data. Triangular vanes attached to the trailing edge of flat steel rails, mounted 10 cm from the inside of the jet exit walls, have been used to reduce this effect; attention is presently given to methods used to reduce the inherent noise generation of the vanes while retaining their pulsation reduction features.

Martin, R. M.↗

NASA NTRS1985

Background noise measurements from jet exit vanes designed to reduced flow pulsations in an open-jet wind tunnel

Many open jet wind tunnels experience pulsations of the flow which are typically characterized by periodic low frequency velocity and pressure variations. One method of reducing these fluctuations is to install vanes around the perimeter of the jet exit to protrude into the flow. Although these vanes were shown to be effective in reducing the fluctuation content, they can also increase the test section background noise level. The results of an experimental acoustic program in the Langley 4- by 7-Meter Tunnel is presented which evaluates the effect on tunnel background noise of such modifications to the jet exit nozzle. Noise levels for the baseline tunnel configuration are compared with those for three jet exit nozzle modifications, including an enhanced noise reduction configuration that minimizes the effect of the vanes on the background noise. Although the noise levels for this modified vane configuration were comparable to baseline tunnel background noise levels in this facility, installation of these modified vanes in an acoustic tunnel may be of concern because the noise levels for the vanes could be well above background noise levels in a quiet facility.

Hoad, D. R.↗

NASA NTRS1984

Comparison of experimental and analytical predictions of rotor blade-vortex interactions using model scale acoustic data

Helicopter blade-vortex interaction (BVI) noise is studied using a model scale rotor acoustic data base and an analytical rotor wake prediction method. The variation of BVI acoustic levels with vehicle flight conditions (forward speed and disk attitude) is presented. Calculations of probable BVI locations on the rotor disk are made for a range of operating conditions using the measured acoustic signals and an acoustic ray tracing technique. Analytical predictions of possible BVI locations on the rotor disk are made using a generalized distorted wake analysis program. Comparisons of the interaction locations are made with the results of both the analytic approach and the acoustic ray tracing technique.

Martin, R. M.↗

NASA NTRS1984

Noise and performance characteristics of a model scale X-wing rotor system in hover

Noise data for the hover condition were measured for a 8 m diameter X-wing model rotor mounted on an outdoor whirl tower. The noise was found to be a function of operating condition, in general increasing with performance. The X-wing spectra obtained from narrowband and 1/3-octave band analyses were dominated by the blade passage frequency harmonics. The circulation control slot blowing produced 1 to 10 kHz broadband noise which exhibited a jet velocity to the 5.4 dependency. Under the rotor plane loading noise was dominant, except at low values of blade pressure ratio where a sharp decrease in the blade passage frequency harmonic levels was observed. In the rotor plane, the contribution of the broadband noise sources was greater than under the rotor plane. The X-wing rotor system in hover exhibited flexibility in operating conditions to achieve a specific level of performance. The high collective, low blade passage ratio combinations which meet a given level of performance were associated with low overall sound pressure levels.

Willshire, W. L., Jr.↗

NASA NTRS1984

Comparison of noise prediction for the X-wing system and a conventional rotor in hover

Analytic predictions of X-wing rotor noise levels in hover without circulation control are presented and compared with measured data at two observer locations. Agreement of predictions and data is best in the rotor plane, due to the dominance of thickness noise terms. Predictions are made for the X-wing and a conventional type rotor system and are compared at two locations at the same tip speed and at each rotor's design tip speed. The acoustic signal of the X-wing is more heavily influenced by thickness noise terms than the conventional rotor. The comparison of each rotor's noise levels depends on the observer location and the amount of circulation control blowing employed.

Martin, R. M.↗

NASA NTRS1983

A note on the tip noise of rotating blades

A possible cause is suggested for the discrepancies that have arisen between measured results and linear acoustic predictions (based on thickness noise alone), at least at the lower tip Mach number range of the tests. The blade tip is shown to be an effective noise generation area when Isom's thickness noise formula is studied numerically (Farassat and Nystrom, 1980). It is found that neglecting the sources on the airfoil-shaped cut at the very tip of the blade causes serious errors in the predicted thickness noise. It is also found that the tip area becomes less important as the tip speed is increased. The effect of the tip surface on the thickness noise indicates that it should be included in the calculation of the loading noise.

Farassat, F.↗

NASA NTRS1981

User's manual for a computer program to calculate discrete frequency noise of conventional and advanced propellers

A user's manual is presented for a computer program for the calculation of discrete frequency noise of conventional and advanced propellers. The structure of the program and the subroutines describing the input functions are discussed. Input variables and their default values and the variables in the output data sheet are defined. Two versions of the program are available. These differ only in the graphic output capability. One version has only printed output capability. A second version with extensive graphic output capability is available for the computer system at Langley. This Manual includes four detailed examples of both the printed and graphic outputs. These examples may be reproduced by users to check their code on their computer system.

Martin, R. M.↗