Engineering topics

Maskew, B.

Publications and source records attributed to Maskew, B..

At least 19 records

NASA NTRS1986

Unsteady low-speed aerodynamic model for complete aircraft configurations

A method for converting steady state, potential panel methods into a time-dependent mode is derived and applied to several test cases. For this development, an improved vortex wake model was constructed which was also suitable for simulating the leading edge separation of slender wings at high angles of attack. Computed flow-field simulations are presented for various unsteady, and high-angle-of-attack conditions, involving geometries such as simple wings, rotors, and complete aircraft configurations.

Katz, J.↗

NASA NTRS1985

Study for prediction of rotor/wake/fuselage interference, part 1

A method was developed which allows the fully coupled calculation of fuselage and rotor airloads for typical helicopter configurations in forward flight. To do this, an iterative solution is carried out based on a conventional panel representation of the fuselage and a blade element representation of the rotor where fuselage and rotor singularity strengths are determined simultaneously at each step and the rotor wake is allowed to relax (deform) in response to changes in rotor wake loading and fuselage presence. On completion of the iteration, rotor loading and inflow, fuselage singularity strength (and, hence, pressure and velocity distributions) and rotor wake are all consistent. The results of a fully coupled calculation of the flow around representative helicopter configurations are presented. The effect of fuselage components on the rotor flow field and the overall wake structure is detailed and the aerodynamic interference between the different parts of the aircraft is discussed.

Clark, D. R.↗

NASA NTRS1985

Study for prediction of rotor/wake/fuselage interference. Part 2: Program users guide

A method was developed which permits the fully coupled calculation of fuselage and rotor airloads for typical helicopter configurations in forward flight. To do this, an iterative solution is carried out based on a conventional panel representation of the fuselage and a blade element representation of the rotor where fuselage and rotor singularity strengths are determined simultaneously at each step and the rotor wake is allowed to relax (deform) in response to changes in rotor wake loading and fuselage presence. On completion of the iteration, rotor loading and inflow, fuselage singularity strength (and, hence, pressure and velocity distributions) and rotor wake are all consistent. The results of a fully coupled calculation of the flow around representative helicopter configurations are presented. The effect of fuselage components on the rotor flow field and the overall wake structure is discussed as well as the aerodynamic interference between the different parts of the aircraft. Details of the computer program are given.

Clark, D. R.↗

NASA NTRS1985

Inviscid analysis of unsteady blade tip flow correlation studies

Two computer programs, VSAERO-TS and VSAERO-H, were used for computing the unsteady subsonic aerodynamic characteristics of arbitrarily shaped wings oscillating in pitch. Program VSAERO-TS is a time-stepping analysis capable of treating large amplitude motions while program VSAERO-H uses harmonic wake and small amplitude assumptions. A comparison between the computed (VSAERO-TS and VSAERO-H) and DFVLR test results for chordwise pressure distributions for rectangular, swept, taper and ogee blade tips is presented in this report. A wide range of angles of attack (mean) from 0 to 12 deg and reduced frequencies of 0.1, 0.2 and 0.3 are covered in this report. Also, the comparison includes several spanwise stations.

Rao, B. M.↗

NASA NTRS1985

Investigation to advance prediction techniques of the low-speed aerodynamics of V/STOL aircraft

A computer program, VSAERO, has been applied to a number of V/STOL configurations with a view to advancing prediction techniques for the low-speed aerodynamic characteristics. The program couples a low-order panel method with surface streamline calculation and integral boundary layer procedures. The panel method--which uses piecewise constant source and doublet panels-includes an iterative procedure for wake shape and models boundary layer displacement effect using the source transpiration technique. Certain improvements to a basic vortex tube jet model were installed in the code prior to evaluation. Very promising results were obtained for surface pressures near a jet issuing at 90 deg from a flat plate. A solid core model was used in the initial part of the jet with a simple entrainment model. Preliminary representation of the downstream separation zone significantly improve the correlation. The program accurately predicted the pressure distribution inside the inlet on the Grumman 698-411 design at a range of flight conditions. Furthermore, coupled viscous/potential flow calculations gave very close correlation with experimentally determined operational boundaries dictated by the onset of separation inside the inlet. Experimentally observed degradation of these operational boundaries between nacelle-alone tests and tests on the full configuration were also indicated by the calculation. Application of the program to the General Dynamics STOL fighter design were equally encouraging. Very close agreement was observed between experiment and calculation for the effects of power on pressure distribution, lift and lift curve slope.

Maskew, B.↗

NASA NTRS1985

Airloads on bluff bodies, with application to the rotor-induced downloads on tilt-rotor aircraft

The aerodynamic characteristics of airfoils with several flap configurations were studied theoretically and experimentally in environments that simulate a wing immersed in the downwash of a hovering rotor. Special techniques were developed for correcting and validating the wind tunnel data for large blockage effects, and the test results were used to evaluate two modern blockage effects, and the test results were used to evaluate two modern computational aerodynamics codes. The combined computed and measured results show that improved flap and leading-edge configurations can be designed which will achieve large reductions in the downloads of tilt-rotor aircraft, and thereby improve their hover efficiency.

Mccroskey, W. J.↗

NASA NTRS1984

The application of a low-order panel method - program VSAERO to powerplant and airframe flow studies

Results from the application of VSAERO, a low-order panel method, to three practical aircraft configurations are presented. The Grumman 698-411 tilt-nacelle V/STOL model is analyzed with particular emphasis on the inlet pressures and the nacelle/fuselage interference effects. Excellent correlation with experiment is reported for the inlet pressure ratio and the inlet operational boundaries. Analysis of an inlet designed for a tilt-rotor/nacelle aircraft is presented. The code was used in a design environment for this configuration to determine an inlet geometry that maintained attached flow for three design flight conditions: hover, hover-transition and cruise. VSAERO is also used to examine the prop-slipstream induced loading for the Langley prop-fan configuration. The versatility and economy of the aerodynamic modeling program, VSAERO, is demonstrated.

Strash, D. J.↗

NASA NTRS1984

The application of a second generation low-order panel method - program 'Vsaero' - to powerplant installation studies

Results from the application of a second generation low-order panel method to a number of powerplant installations are presented. The method, which retains the advantages of ease of use and low operating cost of earlier panel methods while retaining the aerodynamic modelling rigor of higher-order methods was used to predict the flow in and around typical nacelles and aircraft for a wide range of conditions. The ability of the second generation low-order analysis to calculate internal flows without the leakage problems associated with earlier programs is demonstrated and correlation between calculated and measured surface pressures and flow behavior, including predicting streamlines and locating regions of separated flow, is presented.

Clark, D. R.↗

NASA NTRS1983

Airloads on bluff bodies, with application to the rotor-induced downloads on tilt-rotor aircraft

Mccroskey, W. J.↗

NASA NTRS1983

Predicting aerodynamic characteristics of vortical flows on three-dimensional configurations using a surface-singularity panel method

A general low-order surface-singularity panel method is used to predict the aerodynamic characteristics of a problem where a wing-tip vortex from one wing closely interacts with an aft mounted wing in a low Reynolds Number flow; i.e., 125,000. Nonlinear effects due to wake roll-up and the influence of the wings on the vortex path are included in the calculation by using a coupled iterative wake relaxation scheme. The interaction also affects the wing pressures and boundary layer characteristics: these effects are also considered using coupled integral boundary layer codes and preliminary calculations using free vortex sheet separation modelling are included. Calculated results are compared with water tunnel experimental data with generally remarkably good agreement.

Maskew, B.↗

NASA NTRS1982

PROGRAM VSAERO: A computer program for calculating the non-linear aerodynamic characteristics of arbitrary configurations: User's manual

VSAERO is a computer program used to predict the nonlinear aerodynamic characteristics of arbitrary three-dimensional configurations in subsonic flow. Nonlinear effects of vortex separation and vortex surface interaction are treated in an iterative wake-shape calculation procedure, while the effects of viscosity are treated in an iterative loop coupling potential-flow and integral boundary-layer calculations. The program employs a surface singularity panel method using quadrilateral panels on which doublet and source singularities are distributed in a piecewise constant form. This user's manual provides a brief overview of the mathematical model, instructions for configuration modeling and a description of the input and output data. A listing of a sample case is included.

Maskew, B.↗

NASA NTRS1982

Calculation of rotor/airframe interference for realistic configurations

The results of a fully coupled calculation of the flow around representative helicopter configurations are presented. The effect of fuselage components on the rotor flowfield and the overall wake structure is detailed and the aerodynamic interference between the different parts of the aircraft is discussed. In particular, the flowfield developed by the rotor head is followed and the effect of a rotor head cap and pylon modifications in redirecting the rotor head flow are illustrated. Good correlation between measured and calculated fuselage airloads in low-speed flight is achieved and correspondence with observed flowfield behavior is demonstrated.

Clark, D. R.↗

NASA NTRS1982

Flows over wings with leading-edge vortex separation

The unsteady cross flow analogy reduces the steady three dimensional separation flow problem into an unsteady two dimensional flow problem in which the section shape changes with time. The two dimensional VORSEP code is extended to the case of arbitrary body growth rates in order to generate the initial vortex structures for the three dimensional free vortex sheet (FVS) code. Automatic procedures to reduce the wing geometry definition to a set of cross flow plane sections corresponding to the locations of the time step solutions and to generate the effective source distribution on each cross flow section to represent the section normal growth across the following steps are incorporated in the VORSEP code. Also, the wake shedding model is improved by adopting a redistribution scheme which improves the stability of the free sheet development with time. The improved wake shedding model combined with the redistribution scheme alleviated the numerical instabilities associated with the vortex rollup.

Rao, B. M.↗

NASA NTRS1982

Calculation of vortex flows on complex configurations

The calculation of aerodynamic characteristics of complex configurations having strongly coupled vortex flows is a non-linear problem requiring iterative solution techniques. This paper discusses the use of a low-order panel method as a means of obtaining practical solutions to such problems. The panel method is based on piecewise constant source and doublet quadrilateral panels and uses the internal Dirichlet boundary condition of zero perturbation potential. The problems of predicting vortex/surface interaction and vortex separation are discussed. Some example calculations are included but further test cases have yet to be carried out, in particular for comparisons with experimental data. The problem of convergence on the iterative calculation for the shape of the free vortex sheet is addressed and a preprocessor routine, based on an unsteady, two-dimensional version of the panel method, is put forward as a cost-effective way of generating an initial vortex structure for use as a starting solution for general configurations.

Maskew, B.↗

NASA NTRS1981

Prediction of aerodynamic characteristics for wings with extensive separations

The development of a simple yet effective technique for modelling the effects of trailing edge separation is discussed. The model encloses the low energy region with free vortex sheets coupled with a potential flow panel method. The technique includes an interation cycle between viscous and potential flow routines and its development from the two dimensional case to the three dimensional case is discussed. A description of the potential flow panel method, which is based on an internal Dirichlet boundary condition, is included.

Maskew, B.↗

NASA NTRS1980

Calculation of two dimensional vortex/surface interference using panel methods

The application of panel methods to the calculation of vortex/surface interference characteristics in two dimensional flow was studied over a range of situations starting with the simple case of a vortex above a plane and proceeding to the case of vortex separation from a prescribed point on a thick section. Low order and high order panel methods were examined, but the main factor influencing the accuracy of the solution was the distance between control stations in relation to the height of the vortex above the surface. Improvements over the basic solutions were demonstrated using a technique based on subpanels and an applied doublet distribution.

Maskew, B.↗

NASA NTRS1980

An analysis method for multi-component airfoils in separated flow

The multi-component airfoil program (Langley-MCARF) for attached flow is modified to accept the free vortex sheet separation-flow model program (Analytical Methods, Inc.-CLMAX). The viscous effects are incorporated into the calculation by representing the boundary layer displacement thickness with an appropriate source distribution. The separation flow model incorporated into MCARF was applied to single component airfoils. Calculated pressure distributions for angles of attack up to the stall are in close agreement with experimental measurements. Even at higher angles of attack beyond the stall, correct trends of separation, decrease in lift coefficients, and increase in pitching moment coefficients are predicted.

Rao, B. M.↗

NASA NTRS1980

Influence of rotor blade tip shape on tip vortex shedding - An unsteady, inviscid analysis

An unsteady potential flow panel method is described based on a time-stepping procedure and using planar quadrilateral panels to represent the surface of thick blades. Each panel has a constant source and doublet distribution and a central control point where an internal Dirichlet boundary condition is applied. The method includes detail paneling around the tip edge and offers the facility of prescribing a tip-edge separation. Preliminary results are shown for four blade tip shapes which are treated as semi-span wings oscillating in pitch about a mean angle of attack of 6 deg. Further work is planned for the wake model before proceeding to higher angles of attack.

Maskew, B.↗