Engineering topics

Mason, M. L.

Publications and source records attributed to Mason, M. L..

17 records

NASA NTRS1988

Vectoring Single Expansion Ramp Nozzle (VSERN) static model test program

A variable throat-area, side-vectoring single expansion ramp nozzle (VSERN) concept's internal performance characteristics are studied with a view to controlling the bypass flow of an unmixed turbofan engine. Static tests have been conducted on VSERN at NASA-Langley using a variety of parametric models giving attention to the effects of upstream bend angle, ramp geometry, area ratio, and nozzle pressure ratio on static thrust and flow performance. Advantages of VSERN over the conventional vectoring axisymmetric convergent side-nozzles typified by those of the Harrier's Pegasus engine.

Eames, D. J. H.↗

NASA NTRS1986

Multiaxis aircraft control power from thrust vectoring at high angles of attack

Extensive research programs conducted at the Langley Research Center have shown that thrust vectoring can be provided by multifunction (nonaxisymmetric) nozzles. Most of this research has been conducted on pitch vectoring at both static and forward flight conditions. Recent efforts have been aimed at evaluating yaw vectoring concepts at static (wind off) conditions. This paper summarizes results for three different twin-engine fighter configurations tested over a Mach number range of 0.15 to 2.47 at angles of attack up to 35 deg. The objective of these investigations was to determine the multiaxis control power characteristics provided by thrust vectoring. All three configurations employed two-dimensional convergent-divergent nozzles which provided pitch vectoring by differential deflection of the upper and lower nozzle divergent flaps. Three different means of yaw vectoring were tested: (1) a translating nozzle sidewall; (2) yaw flaps located in the nozzle sidewalls; and (3) canted nozzles. These investigations were conducted in the Langley 16-Foot Transonic Tunnel and the Lewis 10x10-Foot Supersonic Tunnel. Longitudinal and direction control power from thrust vectoring was greater than that provided by aerodynamic control effectors at low speed or at high angles of attack.

Capone, F. J.↗

NASA NTRS1986

Static investigation of two STOL nozzle concepts with pitch thrust-vectoring capability

A static investigation of the internal performance of two short take-off and landing (STOL) nozzle concepts with pitch thrust-vectoring capability has been conducted. An axisymmetric nozzle concept and a nonaxisymmetric nozzle concept were tested at dry and afterburning power settings. The axisymmetric concept consisted of a circular approach duct with a convergent-divergent nozzle. Pitch thrust vectoring was accomplished by vectoring the approach duct without changing the nozzle geometry. The nonaxisymmetric concept consisted of a two dimensional convergent-divergent nozzle. Pitch thrust vectoring was implemented by blocking the nozzle exit and deflecting a door in the lower nozzle flap. The test nozzle pressure ratio was varied up to 10.0, depending on model geometry. Results indicate that both pitch vectoring concepts produced resultant pitch vector angles which were nearly equal to the geometric pitch deflection angles. The axisymmetric nozzle concept had only small thrust losses at the largest pitch deflection angle of 70 deg., but the two-dimensional convergent-divergent nozzle concept had large performance losses at both of the two pitch deflection angles tested, 60 deg. and 70 deg.

Mason, M. L.↗

NASA NTRS1985

Port geometry effects on thrust reverser static performance

An investigation has been conducted to provide some insight into the effect of several geometric parameters on the internal performance of thrust reverser ports for nonaxisymmetric nozzles using a single port test apparatus. This test apparatus simulates thrust reversal (conceptually) which would occur in the convergent section of the forward flight nozzle or in the constant area duct just upstream. The port opening had an aspect ratio of 6.1 (throat width/throat height) and had constant passage area from the geometric throat to the exit. The geometric parameters investigated were port angle, port corner radius, port location, and flow blocker angle. The apparatus had a single port so that thrust (vector) angle could be obtained from force balance measurements. The tests were conducted in the Static Test Stand of the Langley 16-Foot Transonic Tunnel at nozzle pressure ratios from 1.5 to 8.0 using high pressure air for propulsion simulation. Port angles (measured forward from a horizontal reference line) investigated were 75, 90, 120 and 135 deg. Sharp and rounded port corners were investigated for each port angle. Discharge coefficient, thrust ratio, and passage static pressures were measured.

Re, R. J.↗

NASA NTRS1985

Static investigation of several yaw vectoring concepts on nonaxisymmetric nozzles

A test has been conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the flow-turning capability and the effects on nozzle internal performance of several yaw vectoring concepts. Nonaxisymmetric convergent-divergent nozzles with throat areas simulating dry and afterburning power settings and single expansion ramp nozzles with a throat area simulating a dry power setting were modified for yaw thrust vectoring. Forward-thrust and pitch-vectored nozzle configurations were tested with each yaw vectoring concept. Four basic yaw vectoring concepts were investigated on the nonaxisymmetric convergent-divergent nozzles: (1) translating sidewall; (2) downstream (of throat) flaps; (3) upstream (of throat) port/flap; and (4) powered rudder. Selected combinations of the rudder with downstream flaps or upstream port/flap were also tested. A single yaw vectoring concept, post-exit flaps, was investigated on the single expansion ramp nozzles. All testing was conducted at static (no external flow) conditions and nozzle pressure ratios varied from 2.0 up to 10.0.

Mason, M. L.↗

NASA NTRS1984

Interference effects of thrust reversing on horizontal tail effectiveness of twin-engine fighter aircraft at Mach numbers from 0.15 to 0.90

An investigation was conducted in the Langley 16 foot Transonic Tunnel to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach and in-flight speeds. Twin vertical tails at three longitudinal locations were tested at a cant angle of 0 deg. One configuration was also tested at a cant angle of 20 deg. Two nonaxisymmetric nozzle reverser concepts were studied. Test data were obtained at Mach numbers of 0.15, 0.60, and 0.90 and at angles of attack from -3 to 9 deg. Nozzle pressure ratios varied from jet off to 7.0, depending upon Mach number. At landing approach speed (Mach number 0.15), thrust reverser operation usually resulted in large variations (up to 70% increase) in horizontal tail effectiveness as nozzle pressure ratio was varied at zero angle of attack or as angle of attack was varied at constant nozzle pressure ratio. There was always a decrease in effectiveness at Mach numbers of 0.60 and 0.90 as a result of reverser operation.

Capone, F. J.↗

NASA NTRS1984

Aeropropulsive characteristics of nonaxisymmetric-nozzle thrust reversers at Mach numbers from 0 to 1.20

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the performance of nonaxisymmetric-nozzle thrust reversers installed on a generic twin-engine fighter aircraft model. Test data were obtained at static conditions and at Mach numbers from 0.15 to 1.20 with jet exhaust simulated by high pressure air. Results showed that reverse-thrust levels of greater than 50 percent at static conditions and greater than 30 percent at in-flight conditions could be achieved. Internal reverser-port passage length was found to be very important in improving reverser performance. Increasing the reverser-port passage length improved reverse-thrust performance by as much as 28 percent at static conditions and by as much as 17 percent at Mach 1.20.

Carson, G. T., Jr.↗

NASA NTRS1983

A static investigation of yaw vectoring concepts on two-dimensional convergent-divergent nozzles

The flow-turning capability and nozzle internal performance of yaw-vectoring nozzle geometries were tested in the NASA Langley 16-ft Transonic wind tunnel. The concept was investigated as a means of enhancing fighter jet performance. Five two-dimensional convergent-divergent nozzles were equipped for yaw-vectoring and examined. The configurations included a translating left sidewall, left and right sidewall flaps downstream of the nozzle throat, left sidewall flaps or port located upstream of the nozzle throat, and a powered rudder. Trials were also run with 20 deg of pitch thrust vectoring added. The feasibility of providing yaw-thrust vectoring was demonstrated, with the largest yaw vector angles being obtained with sidewall flaps downstream of the nozzle primary throat. It was concluded that yaw vector designs that scoop or capture internal nozzle flow provide the largest yaw-vector capability, but decrease the thrust the most.

Berrier, B. L.↗

NASA NTRS1983

Aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed with forward-swept wings and canards

The Langley 16 foot transonic tunnel was used to determine the aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed in a wing-body configuration with forward-swept wings. The configuration was tested with and without fixed canards. The test conditions included free-stream Mach numbers of 0.60, 0.90, and 1.20. The model angle of attack ranged from -2 deg to 14 deg; the nozzle pressure ratio ranged from 1.0 (jet off) to 9.0. The Reynolds number based on the wing mean aerodynamic chord varied from 3.0 x 10 to the 6th power to 4.8 x 10 to the 6th power, depending on Mach number. Aerodynamic characteristics were analyzed to determine the effects of thrust vectoring and the canard effects on the wing-afterbody-nozzle and the wing-afterbody portions of the model. Thrust vectoring had no effect on the angle of attack for the onset of flow separation on the wing but resulted in reduced drag at angle-of-attack values above that required for wing flow separation. The canard was found to have little effect on the thrust-induced lift resulting from vectoring, since canard effects occurred primarily on the wing.

Mason, M. L.↗

NASA NTRS1983

Thrust reversing effects on horizontal tail effectiveness of twin-engine fighter aircraft

The Langley Research Center has conducted an experimental program to determine the interference effects of thrust reversing on horizontal tail effectiveness of a twin engine, general research fighter model at approach (Mach number 0.15) and in-flight (Mach number 0.60 and 0.90) speeds. Twin vertical tails were tested at three longitudinal locations. Two nonaxisymmetric nozzle reverser concepts were studied. The effects of thrust reversing on horizontal tail effectiveness were found to be very dependent upon vertical tail locations. At approach speeds thrust reverser operation usually resulted in large variations in horizontal tail effectiveness as either nozzle pressure ratio or model angle of attack was varied. Either increases or decreases in tail effectiveness ocurred due to reverse operation depending upon tail location. At in-flight conditions there were always decreases in tail effectiveness due to reverser operation regardless of vertical tail location.

Capone, F. J.↗

NASA NTRS1982

Experimental investigation of two nonaxisymmetric wedge nozzles at free stream Mach numbers up to 1.20

Forces and pressures on two nonaxisymmetric wedge nozzles were measured in a 16 foot transonic tunnel. Tests were conducted at static conditions and at free stream Mach numbers of 0.60, 0.80, 0.90, 0.94, and 1.20. The range of nozzle pressure ratios varied with configuration and Mach number. The internal and external geometry of the nozzles and the test model are defined in detail. Nozzle performance data are presented as discharge coefficients, internal thrust ratios, thrust minus nozzle drag ratios, and ideal thrust coefficients. Extensive internal and external pressure measurements are presented.

Mason, M. L.↗

NASA NTRS1980

The effect of throat contouring on two-dimensional converging-diverging nozzles at static conditions

An experiment was conducted at static conditions to determine the internal performance effects of nozzle throat contouring, the result of increasing the circular-arc throat radius. Five nonaxisymmetric converging-diverging nozzles were tested at nozzle pressure ratios up to 9.0. Data are presented as internal thrust ratios, discharge coefficients, and static-pressure distributions. Comparisons of internal performance data for the five nozzles show that throat contouring increases the value of discharge coefficient but has no significant effect on internal thrust ratio except in cases of internal flow separation. To illustrate the use of the two dimensional converging-diverging (2-D C-D) nozzle data base, a two dimensional inviscid theory was applied to the five configurations. The generally good agreement of data with theoretical results indicates that two-dimensional inviscid theory can be successfully applied to the prediction of 2-D C-D nozzle internal flow.

Mason, M. L.↗

NASA NTRS1979

Pitot pressure measurements in flow fields behind circular-arc nozzles with exhaust jets at subsonic free-stream Mach numbers

The flow field behind a circular arc nozzle with exhaust jet was studied at subsonic free stream Mach numbers. A conical probe was used to measure the pitot pressure in the jet and free stream regions. Pressure data were recorded for two nozzle configurations at nozzle pressure ratios of 2.0, 2.9, and 5.0. At each set of test conditions, the probe was traversed from the jet center line into the free stream region at seven data acquisition stations. The survey began at the nozzle exit and extended downstream at intervals. The pitot pressure data may be applied to the evaluation of computational flow field models, as illustrated by a comparison of the flow field data with results of inviscid jet plume theory.

Mason, M. L.↗

NASA NTRS1978

Experimental and analytical investigation of a nonaxisymmetric wedge nozzle at static conditions

An experimental investigation of a nonaxisymmetric wedge nozzle was conducted at static conditions. The resulting data, in the form of detailed pressure distributions and oil flow photographs, expand the current nonaxisymmetric nozzle data base. An analytical investigation has been conducted to evaluate a two-dimensional, inviscid, time-dependent theory as a nonaxisymmetric nozzle performance predictor. For the range of nozzle pressure ratios investigated, results indicate good agreement between theory and experiment in regions of predominately two-dimensional flow and limited agreement in regions of three-dimensional flow. For the wedge nozzle and related nozzle configurations, the two dimensional, inviscid theory may be applied as a limited performance predictor.

Carson, G. T., Jr.↗

NASA NTRS1977

The mass of Phobos

Radio tracking data associated with the February 1977 encounters between the Martian satellite Phobos and the Viking Orbiter I spacecraft have been analyzed to determine the gravitational constant of Phobos. A linear error analysis was conducted to determine the selection of data and the parameter solution set which would yield the best estimate of the gravitational constant. This error analysis indicated that the optimal data set was a data arc beginning just prior to the closest encounter and spanning three consecutive spacecraft orbits; data near periapsis were deleted. The most feasible parameter solution set consisted of the Phobos gravitational constant and the spacecraft initial conditions. The result of the data analysis was an estimate of (7.3 plus or minus 0.7) x 10 to the -4th cu km/sq sec for the gravitational constant of Phobos.

Tolson, R. H.↗

NASA NTRS1975

Accuracy of estimating the masses of Phobos and Deimos from multiple Viking orbiter encounters

The problem was investigated of estimating the masses of Phobos and Deimos from Doppler and onboard optical measurements during the Viking extended mission. A Kalman filter was used to analyze the effects of gravitational uncertainties and nongravitational accelerations. These accelerations destroy the dynamical integrity of the orbit, and multibatch or limited memory filtering is preferred to single batch processing. Optical tracking is essential to improve the relative orbit geometry. The masses can be determined to about 10% and 25% respectively for Phobos and Deimos, assuming satellite densities of about 3 gr/cu cm.

Tolson, R. H.↗

NASA NTRS1975

Accuracy of estimating the masses of Phobos and Deimos from multiple Viking orbiter encounters

This paper addresses the problem of estimating the masses of Phobos and Deimos from Doppler and onboard optical measurements during the Viking extended mission. A Kalman filter is used to analyze the effects of gravitational uncertainties and nongravitational accelerations. These accelerations destroy the dynamical integrity of the orbit and multi-batch or limited memory filtering is preferred to single batch processing. Optical tracking is essential to improve the relative orbit geometry. The masses can be determined to about 10% and 25% respectively for Phobos and Deimos, assuming satellite densities of about 3 g per cu cm.

Tolson, R. H.↗