Two-dimensional MXene based anodic slurry electrodes for vanadium redox flow batteries
Not Available
Engineering topics
Publications and source records attributed to Matthews, Kyle.
Not Available
Abstract A multifunctional soft material with high ionic and electrical conductivity, combined with high mechanical properties and the ability to change shape can enable bioinspired responsive devices and systems. The incorporation of all these characteristics in a single material is very challenging, as the improvement of one property tends to reduce other properties. Here, a nanocomposite film based on charged, high‐aspect‐ratio 1D flexible nanocellulose fibrils, and 2D Ti 3 C 2 T x MXene is presented. The self‐assembly process results in a stratified structure with the nanoparticles aligned in‐plane, providing high ionotronic conductivity and mechanical strength, as well as large water uptake. In hydrogel form with 20 wt% liquid, the electrical conductivity is over 200 S cm −1 and the in‐plane tensile strength is close to 100 MPa. This multifunctional performance results from the uniquely layered composite structure at nano‐ and mesoscales. A new type of electrical soft actuator is assembled where voltage as low as ±1 V resulted in osmotic effects and giant reversible out‐of‐plane swelling, reaching 85% strain.
While transition‐metal oxides such as α‐MoO 3 provide high capacity, their use is limited by modest electronic conductivity and electrochemical instability in aqueous electrolytes. Two‐dimensional (2D) MXenes, offer metallic conductivity, but their capacitance is limited in aqueous electrolytes. Insertion of partially solvated cations into Ti 3 C 2 MXene from lithium‐based water‐in‐salt (WIS) electrolytes enables charge storage at positive potentials, allowing a wider potential window and higher capacitance. Herein, we demonstrate that α‐MoO 3 /Ti 3 C 2 hybrids combine the high capacity of α‐MoO 3 and conductivity of Ti 3 C 2 in WIS (19.8 m LiCl) electrolyte in a wide 1.8 V voltage window. Cyclic voltammograms reveal multiple redox peaks from α‐MoO 3 in addition to the well‐separated peaks of Ti 3 C 2 in the hybrid electrode. This leads to a higher specific charge and a higher rate capability compared to a carbon and binder containing α‐MoO 3 electrode. These results demonstrate that the addition of MXene to less conductive oxides eliminates the need for conductive carbon additives and binders, leads to a larger amount of charge stored, and increases redox capacity at higher rates. In addition, MXene encapsulated α‐MoO 3 showed improved electrochemical stability, which was attributed to the suppressed dissolution of α‐MoO 3 . The work suggests that oxide/MXene hybrids are promising for energy storage.
Not provided.
The dynamical structural response of MXenes during electrochemical ion intercalation is critical for their functionality in fast chemical actuation and high-power electrical energy storage but has yet to be observed. Here, the dynamically evolving layer spacing of a Ti 3 C 2 T $x$ MXene film was observed using time-resolved operando X-ray reflectivity during cyclic voltammetry for applied potentials between +0.3 and -0.7 V (vs Ag/AgCl) at sweep rates 1 ≤ $v$ ≤ 500 mV/s. The pseudocapacitive electrochemical MXene response in the aqueous 0.1 M Li 2 SO 4 electrolyte, including both capacitive and redox characteristics, is characterized by kinetically limited lithium intercalation and layer contraction. In conclusion, two types of dynamical responses were observed: slow and fast lattice contraction regimes versus applied potential are correlated with the capacitive and redox features, respectively, with structural relaxation rates that scale as ~$v$ 1/2 and ~$v$, revealing two distinct dynamical structural responses during electrochemical ion intercalation.