Engineering topics

Mauro, Stephanie L.

Publications and source records attributed to Mauro, Stephanie L..

3 records

NASA NTRS2021

Extended Stroke and Miniaturized Reverse-Operation DTE Thermal Switches

This paper describes two advanced thermal switches under development that are offshoots of the recently flight-qualified 2500:1 reverse-operation differential thermal expansion (DTE) thermal switch (ROD-TSW). The first is the extended stroke ROD-TSW (ES-ROD-TSW) while the second is the miniaturized ROD-TSW (mini-ROD-TSW). Each employs multiple diametrically nested DTE stages in contrast to the single-stage ROD-TSW. The ES-ROD-TSW employs two stages and a negative CTE material known as Allvar and its main purpose is to extend its stroke for use in non-vacuum planetary environments. The mini-ROD-TSW employs four stages to miniaturize its size for use in compact lunar instruments and rovers. The ES-ROD-TSW was TVAC tested at JPL and its ON/OFF ratio is 13000:1 based on a measured ON conductance of 6.89 W/K and a calculated OFF conductance of 0.00053 W/K. The mini-ROD-TSW is targeted to have an ON conductance of 1.5 W/K and an OFF conductance of 0.0015 W/K, both verified by analysis. Test verification of the mini-ROD-TSW remains to be carried out. The paper will provide design/performance details of each device.

Farmer, Jeffery T.↗

NASA NTRS2017

The Iodine Satellite (iSAT) Propellant Feed System - Design and Development

The development, modeling, and testing of components and subsystems required to feed iodine propellant to a 200-W Hall thruster and cathode are described. This work aims to address design deficiencies and issues associated with the propellant feed system that were revealed by an integrated thruster-cathode-feed system test. The feed system design is modified to use materials that are more resistant to the highly-reactive nature of iodine propellant. Dynamic modeling indicates that the inclusion of additional constraints on feed system tubing will reduce the vibrationally-induced stresses that occur during launch. Full spacecraft thermal modeling show that the feed system heater power levels are sufficient to heat the tank and propellant lines to operating temperatures, where iodine in the tank is sublimed to supply propellant for operation and the tubing is elevated in temperature to keep propellant from redepositing to block the flow. Experiments are conducted to demonstrate that is it possible through the application of heating to clear an iodine deposit blocking the flow. Deposits in the low-pressure portion of the system near the exit to vacuum are shown to be relatively easy to remove in this manner while blockages forming upstream nearer to the higher-pressure propellant tank require significantly more effort to remove. Fluid flow modeling of the feed system is performed, exhibiting some qualitative agreement with experimental data. However, the highly viscous nature of the fluid flow and the dependence of the component flow coefficients on the Reynolds number are likely causes of the generally-poor quantitative agreement between the modeling results and experimentally-measured fluid flow properties.

Polzin, Kurt A.↗

NASA NTRS2015

Propulsion System Development for the Iodine Satellite (iSAT) Demonstration Mission

The development and testing of a 200-W iodine-fed Hall thruster propulsion system that will be flown on a 12-U CubeSat is described. The switch in propellant from more traditional xenon gas to solid iodine yields the advantage of high density, low pressure propellant storage but introduces new requirements that must be addressed in the design and operation of the propulsion system. The thruster materials have been modified from a previously-flown xenon Hall thruster to make it compatible with iodine vapor. The cathode incorporated into this design additionally requires little or no heating to initiate the discharge, reducing the power needed to start the thruster. The feed system produces iodine vapor in the propellant reservoir through sublimation and then controls the flow to the anode and cathode of the thruster using a pair of proportional flow control valves. The propellant feeding process is controlled by the power processing unit, with feedback control on the anode flow rate provided through a measure of the thruster discharge current. Thermal modeling indicates that it may be difficult to sufficiently heat the iodine if it loses contact with the propellant reservoir walls, serving to motivate future testing of that scenario to verify the modeling result and develop potential mitigation strategies. Preliminary, short-duration materials testing has thus-far indicated that several materials may be acceptable for prolonged contact with iodine vapor, motivating longer-duration testing. A propellant loading procedure is presented that aims to minimize the contaminants in the feed system and propellant reservoir. Finally, an 80-hour duration test being performed to gain experience operating the thruster over long durations and multiple restarts is discussed.

Polzin, Kurt A.↗