Search NASA⌕ Search

Engineering topics

Mays, Jimmy

Publications and source records attributed to Mays, Jimmy.

At least 73 records · Page 4

Nanostructure of Solid Precipitates Obtained by Expansion of Polystyrene-block-Polybutadiene Solutions in Near Critical Propane: Block Ratio and Micellar Solution Effects

In contrast to incompressible liquid solutions, compressible near-critical solutions of block copolymers allow for controlling rapid structure transformations with pressure alone. For example, when dissolved in near-critical propane, polystyrene-block-polybutadiene can form a random molecular solution at high pressures, a micellar solution at moderate pressures, and a solvent-free precipitate at low pressures. In contrast to the unstructured virgin copolymer, such a propane-treated precipitate rapidly self-assembles toward structures characteristic of equilibrated block copolymers, such as lamellae, spheres, or cylinders, which depend on the block ratio rather than on the decompression rate or temperature, at least within the rate and temperature ranges investigated in this work. At lower temperatures, however, say below 40 C, glass transition of the styrene-butadiene diblocks can inhibit independent structure formation, while crystallization of their hydrogenated-butadiene analogues can preserve the micellar-solution structure.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

High-Strain-Induced Deformation Mechanisms in Block-Graft and Multigraft Copolymers

The molecular orientation behavior and structural changes of morphology at high strains for multigraft and block graft copolymers based on polystyrene (PS) and polyisoprene (PI) were investigated during uniaxial monotonic loading via FT-IR and synchrotron SAXS. Results from FT-IR revealed specific orientations of PS and PI segments depending on molecular architecture and on the morphology, while structural investigations revealed a typical decrease in long-range order with increasing strain. This decrease was interpreted as strain-induced dissolution of the glassy blocks in the soft matrix, which is assumed to affect an additional enthalpic contribution (strain-induced mixing of polymer chains) and stronger retracting forces of the network chains during elongation. Our interpretation is supported by FT-IR measurements showing similar orientation of rubbery and glassy segments up to high strains. It also points to highly deformable PS domains. By synchrotron SAXS, we observed in the neo-Hookean region an approach of glassy domains, while at higher elongations the intensity of the primary reflection peak was significantly decreasing. The latter clearly verifies the assumption that the glassy chains are pulled out from the domains and are partly mixed in the PI matrix. Results obtained by applying models of rubber elasticity to stressstrain and hysteresis data revealed similar correlations between the softening behavior and molecular and morphological parameters. Further, an influence of the network modality was observed (randomgrafted branches). For sphere formingmultigraft copolymers the domain functionality was found to be less important to achieve improved mechanical properties but rather size and distribution of the domains.

36 MATERIALS SCIENCE↗

Combatting Ionic Aggregation using Dielectric Forces Combining Modeling/Simulation and Experimental Results to Explain End-capping of Primary Amine Functionalized Polystyrene

Chain-end functionalization of living poly(styryl)lithium using 1-(3-bromopropyl)-2,2,5,5-tetramethyl-1-aza-2,5-disilacyclo-pentane (BTDP) to generate primary amine end-functionalized polystyrene was investigated using high vacuum anionic polymerization techniques. 13C NMR spectroscopy and Matrix Assisted Laser Desorption Ionization Time of Flight Mass Spectrometry (MALDI-TOF MS) were used to evaluate polymer end-groups and demonstrated that quantitative amine functionalized polymer was attained under appropriate reaction conditions. In general, the polymerization of styrene was conducted in benzene and the end-capping reaction was performed by adding tetrahydrofuran (THF) to the reaction prior to the addition of BTDP in THF at room temperature. Results indicated that approximately 20% THF by volume is required to obtain 100% end-capping free from side reactions. When too little or no THF was present, side reactions such as lithium halogen exchange followed by Wurtz coupling resulted in unfunctionalized head-to-head dimer as well as other byproducts. Modeling and simulation of the solvent effects using hybrid methods (the so-called QM/MM method) suggest that THF effectively dissociated the anionic chain-end aggregation, thereby resulting in the desired primary amine functionalized polymer. Molecular dynamics (MD) simulations were conducted to develop an understanding of the physics of counterions involved in the end-functionalization process.

36 MATERIALS SCIENCE↗

Asymmetrical Self-assembly From Fluorinated and Sulfonated Block Copolymers in Aqueous Media

Block copolymers of fluorinated isoprene and partially sulfonated styrene form novel tapered rods and ribbon-like micelles in aqueous media due to a distribution of sulfonation sites and a large Flory-Huggins interaction parameter. A combination of microscopy, light scattering, and simulation demonstrates the presence of these unique nanostructures. This study sheds light on the micellization behavior of amphiphilic block polymers by revealing a new mechanism of self-assembly.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Assembly and Characterization ofWell-DefinedHigh-Molecular-Weight Poly(p-phenylene) Polymer Brushes

The assembly and characterization of well-de ned, end-tethered poly- (p-phenylene) (PPP) brushes having high molecular weight, low polydispersity and high 1,4-stereoregularity are presented. The PPP brushes are formed using a precursor route that relies on either self-assembly or spin coating of high molecular weight (degrees of poly- merizations 54, 146, and 238) end-functionalized poly(1,3-cyclohexadiene) (PCHD) chains from benzene solutions onto silicon or quartz substrates, followed by aromatization of the end-attached PCHD chains on the surface. The approach allows the thickness (grafting density) of the brushes to be easily varied. The dry brushes before and after aromatization are characterized by ellipsometry, atomic force microscopy, grazing angle attenuated total re ectance Fourier transform infrared spectroscopy, and UV-Vis spectros- copy. The properties of the PPP brushes are compared with those of lms made using oligo- paraphenylenes and with ab initio density functional theory simulations of optical proper- ties. Our results suggest conversion to fully aromatized, end-tetheredPPPpolymerbrusheshaving eective conjugation lengths of 5 phenyl units.

36 MATERIALS SCIENCE↗

Novel Diblock Copolymer-Grafted Multiwalled Carbon Nanotubes via a combination of Living and Controlled/Living Surface Polymerizations

Diels Alder cycloaddition reactions were used to functionalize multiwalled carbon nanotubes (MWNTs) with 1-benzocylcobutene-10-phenylethylene (BCB-PE) or 4-hydroxyethylbenzocyclobutene (BCB-EO). The covalent functionalization of the nanotubes with these initiator precursors was verified by FTIR and thermogravimetric analysis (TGA). After appropriate transformations/additions, the functionalized MWNTs were used for surface initiated anionic and ring opening polymerizations of ethylene oxide and e-caprolactone (e-CL), respectively. The OH-end groups were transformed to isopropylbromide groups by reaction with 2-bromoisobutyryl bromide, for subsequent atom transfer radical polymerization of styrene or 2-dimethylaminoethyl methacrylate to afford the final diblock copolymers. 1H NMR, differential scanning calorimetry (DSC), TGA, and transmission electron microscopy (TEM) were used for the characterization of the nanocomposite materials. TEM images showed the presence of a polymer layer around the MWNTs as well as the dissociation of MWNT bundles. Consequently, this general methodology, employing combinations of different polymerization techniques, increases the diversity of diblocks that can be grafted from MWNTs.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Controllable stacked disk morphologies of charged diblock copolymers

Monte Carlo simulations are used to demonstrate the controlled stacking of charged block copolymer disk morphologies that can be obtained under certain thermodynamic conditions. We examine a partially charged block copolymer where 75% of the blocks are neutral and 25% of the blocks are charged. The presence of strong electrostatic interactions promotes charge agglomeration thereby changing morphologies in these systems. This study relates different thermodynamic quantities for which disk-like stackings can be obtained. The long-range order can be sustained even if hydrophobicity is increased albeit with lower dimensional structures. Our simulation results agree very well with recent experiments and are consistent with theoretical observations of counterion adsorption on flexible polyelectrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Polypeptide Grafted Hyaluronan: Synthesis and Characterization

Poly(L-leucine) grafted hyaluronan (HA-g-PLeu) has been synthesized via a Michael addition reaction between primary amine terminated poly(L-leucine) and acrylate-functionalized HA (TBAHA-acrylate). The precursor hyaluronan was first functionalized with acrylate groups by reaction with acryloyl chloride in the presence of triethylamine in N,N-dimethylformamide. 1H NMR analysis of the resulting product indicated that an increase in the concentration of acryloylchoride with respect to hydroxyl groups on HA has only a moderate effect on functionalization efficiency, f. A precise control of stoichiometry was not achieved, which could be attributed to partial solubility of intermolecular aggregates and the hygroscopic nature of HA. Michael addition at high [PLeu- NH2]/[acrylate]TBAHA ratios gave a molar grafting ratio of only 0.20 with respect to the repeat unit of HA, indicating grafting limitation due to insolubility of the grafted HA-g-PLeu. Soluble HA-g-PLeu graft copolymers were obtained for low grafting ratios (<0.039) with <8.6% by mass of PLeu and were characterized thoroughly using light scattering, 1H NMR, FT-IR, and AFM techniques. Light scattering experiments showed a strong hydrophobic interaction between PLeu chains, resulting in aggregates with segregated nongrafted HA segments. This yields local networks of aggregates, as demonstrated by atomic force microscopy. Circular dichroism spectroscopy showed a -sheet conformation for aggregates of poly(L-leucine).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A New Approach to the Living Anionic Polymerization of 4-Cyanostyrene

A new approach to the synthesis of well-defined homopolymers of 4-cyanostyrene (4CNS) via anionic polymerization using high vacuum techniques is described. This synthetic route is based on the use of a solvent mixture of tetrahydrofuran and N,N-dimethylacetamide (THF/DMA, 4/1 v/v) in order to overcome the previously reported polymer insolubility issue and long reaction times. Our system afforded well-defined linear living P4CNSs having molecular weights up to 98,500 g/mol in less than 30 min and can be applied to the synthesis of P4CNS-based homopolymers and copolymers of various molecular architectures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tunable Morphologies from Charged Block Copolymers

The bulk morphologies formed by a new class of charged block copolymers, 75 vol % fluorinated polyisoprene (FPI) 25 vol% sulfonated polystyrene (PSS) with 50% sulfonation, are characterized, and the fundamental underlying forces that promote the self-assembly processes are elucidated. The results show how the bulk morphologies are substantially different from their uncharged diblock counterparts (PS-PI) and also how morphology can be tuned with volume fraction of the charged block and the casting solvent. A physical understanding based on the underlying strong electrostatic interactions between the charged block and counterions is obtained using Monte Carlo (MC) and Molecular Dynamics (MD) simulations. The 75/25 FPI-PSS shows hexagonal morphologies with the minority blocks (PSS) forming the continuous phase due to charge percolation and the FPI blocks arranged in hexagonal cylinders. Some long-range order can be sustained even if lipophobicity is increased (addition of water), albeit with lower dimensional structures. However, thermal annealing provides sufficient energy to disrupt the percolated charges and promotes aggregation of ionic sites which leads to a disordered system. Diverse and atypical morphologies are readily accessible by simply changing the number distribution of the charges on PSS block.

36 MATERIALS SCIENCE↗

Functionalized organic nanoparticles from core-crosslinked poly(4-vinylbenzocyclobutene-b-butadiene) diblock copolymer micelles

Sufface-functionalized polymeric nanoparticles were prepared by: a) self~assembly of poly(4-vinylbenzocyclobutene-b-butadiene) diblock copolymer (PVBCB-b-PB) to form spherical micelles (diameter:15-48 nm) in decane, a selective solvent for PB, b) crosslinking of the PVBCB core through thermal dimerization at 200-240 ~ C, and c) cleavage of the PB corona via ozonolysis and addition of dimethyl sulfide to afford aldehyde-functionalized nanoparticles (diameter: -16-20 nm), along with agglomerated nanoparticles ranging from - 30 to -100 nm in diameter. The characterization of the diblock copolymer precursors. the intermediate micelles and the final surface-functionalized crosslinked nanoparticles was carried alit by a combination of size exclusion chromatography, static and dynamic light scattering, viscometry, thermogravimetric analysis, 1 H NMR and FfIR spectroscopy and transmission electron microscopy.

36 MATERIALS SCIENCE↗

A novel reactive processing technique: using telechelic polymers to reactively compatibilize polymer blends

Difunctional reactive polymers, telechelics, were used to reactively form multiblock copolymers in situ when melt-blended with a blend of polystyrene and polyisoprene. To quantify the ability of the copolymer to compatibilize the blends, the time evolution of the domain size upon annealing was analyzed by SEM. It was found that the most effective parameter to quantify the ability of the copolymer to inhibit droplet coalescence is Kreltstable, the relative coarsening constant multiplied by the stabilization time. These results indicate that intermediate-molecular-weight telechelic pairs of both highly reactive Anhydride-PS-Anhydride/NH2-PI-NH2 and slower reacting Epoxy-PS-Epoxy/COOH-PI-COOH both effectively suppress coalescence, with the optimal molecular weight being slightly above the critical molecular weight of the homopolymer,Mc. The effects of telechelic loading were also investigated, where the optimal loading concentration for this system was 0.5 wt %, as higher concentrations exhibited a plasticizing effect due to the presence of unreacted low-molecular-weight telechelics present in the blend. A determination of the interfacial coverage of the copolymer shows that a conversion of 1.5-3.0% was required for 20% surface coverage at 5.0 wt % telechelic loading, indicating a large excess of telechelics in this system. At the optimal loading level of 0.5 wt %, a conversion of 15% was required for 20% surface coverage. The results of these experiments provide a clear understanding of the role of telechelic loading and molecular weight on its ability to reactively form interfacial modifiers in phase-separated polymer blends and provide guidelines for the development of similar reactive processing schemes that can use telechelic polymers to reactively compatibilize a broad range of polymer blends.

36 MATERIALS SCIENCE↗

Deuteration Can Impact Micellization Pressure and Cloud Pressure of Polystyrene-block-polybutadiene and Polystyrene-block-polyisoprene in Compressible Propane

The deuterated homopolymers and their corresponding polystyrene-block-polybutadiene and polystyrene-block-polyisoprene copolymers require lower cloud pressures than their hydrogenous analogues to dissolve in a compressible alkane solvent, such as propane. For symmetric diblocks, deuteration reduces the micellization pressure. By contrast, for asymmetric diblocks with a long diene block relative to the styrene block, deuteration can increase the micellization pressure. All in all, however, the deuteration effects, while measurable, do not qualitatively change the principal diblock properties in compressible propane solutions, such as pressure-induced micelle decomposition, micelle formation and micelle size, and their temperature dependence. Therefore, isotope labeling should be a useful approach to neutron-scattering characterization for styrene-diene block copolymers in compressible alkane systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface-Initiated Titanium-Mediated Coordination Polymerization from Catalyst-Functionalized Single and Multiwalled Carbon Nanotubes

Single (SWNTs) and multiwalled (MWNTs) carbon nanotubes were functionalized with a titanium alkoxide catalyst through a Diels-Alder cycloaddition reaction. The catalyst-functionalized carbon nanotubes (CNTs) were used for the surface initiated titanium-mediated coordination polymerizations of L-lactide (L-LA), -caprolactone (-CL) and n-hexyl isocyanate (HIC) employing the grafting from technique. 1H NMR, IR and Raman spectra showed that the precursor catalyst was successfully synthesized and covalently attached on the CNTs surface. Thermogravimetric analysis (TGA) revealed that the grafted poly(L-lactide) (PLLA) content could be controlled with time. The final polymer-grafted CNTs were readily dissolved in organic solvents as compared to the insoluble pristine and catalyst-functionalized CNTs. The presence of thick layers of polymers around the CNTs was observed through transmission electron microscopy (TEM). Differential scanning calorimetry (DSC) proved that the glass transition (Tg) and melting (Tm) temperatures of the PLLA are affected by the presence of the CNTs, while PLLA R-helix conformation remains intact, as revealed by the circular dichroism (CD) spectra.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

High-Pressure Micellar Solutions of Symmetric and Asymmetric Styrene?Diene Diblocks in Compressible Near Critical Solvents: Micellization Pressures and Cloud Pressures Respond but Micellar Cloud Pressures Insensitive to Copolymer Molecular Weight, Concentration, and Block Ratio Changes

Micellar solutions of polystyrene-block-polybutadiene and polystyrene-block-polyisoprene in propane are found to exhibit significantly lower cloud pressures than the corresponding hypothetical nonmicellar solutions. Such a cloud-pressure reduction indicates the extent to which micelle formation enhances the apparent diblock solubility in near-critical and hence compressible propane. Concentration-dependent pressure-temperature points beyond which no micelles can be formed, referred to as the micellization end points, are found to depend on the block type, size, and ratio. The cloud-pressure reduction and the micellization end point measured for styrene-diene diblocks in propane should be characteristic of all amphiphilic diblock copolymer solutions that form micelles in compressible solvents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-Pressure Micellar Solutions of Polystyrene-block-Polybutadiene and Polystyrene-block-Polyisoprene Solutions in Propane Exhibit Cloud-Pressure Reduction and Distinct Micellization End Points

Micellar solutions of polystyrene-block-polybutadiene and polystyrene-block-polyisoprene in propane are found to exhibit significantly lower cloud pressures than the corresponding hypothetical non-micellar solutions. Such a cloud-pressure reduction indicates the extent to which micelle formation enhances the apparent diblock solubility in near-critical and hence compressible propane. Pressure-temperature points beyond which no micelles can be formed, referred to as the micellization end points, are found to depend on the block type, size and ratio, and on the polymer concentration. For a given pressure, the micellization end-point temperature corresponds to the "critical micelle temperature." The cloud-pressure reduction and the micellization end point measured for styrene-diene diblocks in propane should be characteristic of all amphiphilic diblock copolymer solutions that form micelles in compressible solvents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Forces of Interaction between Surfaces Bearing Looped Polymer Brushes in Good Solvent.

In a previous publication we suggested [Huang et al., Macromolecules, 2008, 41, 1745-1752] that looped polymer brushes formed by tethering chains by both ends to a surface may exhibit a polydispersity-like effect due to a distribution of distances between tethering points, leading to segment density profiles dominated by a long and diffuse exponentially-decaying tail. To study this issue in more detail, the force profiles (forces of interaction as a function of separation distance) of a series of looped polymer brushes made by preferential adsorption of poly(2-vinylpyridine)-polystyrene-poly(2-vinylpyridine) (PVP-b-PS-b-PVP) triblock copolymers of varying molecular weight and asymmetry ratio are measured using the surface forces apparatus. The force profiles are analyzed using an equivalent diblock model, which considers the triblock copolymer brushes as being comprised of two diblock copolymers of half the PS molecular weight. While scaling the dependencies of the interaction energy and distance on molecular weight, the tethering density and segment size coalesce the measured force profiles to the universal profile, it is necessary to include polydispersity in the description of the equilibrium structure. This is done using the self-consistent field model of Milner et al. [Macromolecules, 1988, 21, 2610-2619]. For looped brushes formed from the symmetric and moderately symmetric triblock copolymers we find that the polydispersity due to molecular weight distribution effectively accounts for the observed force profiles. On the other hand, agreement between the measured and predicted force profiles of looped brushes formed from highly asymmetric copolymers at low degrees-of-compression is achieved only if a much smaller value of the polydispersity index is used in the fitting. The implication of these results is that the shape of the segment density profiles is not due to the previously proposed anchor-induced polydispersity arising due to loop formation; however in the case of highly asymmetric copolymers, loop formation may constrain the stretching of the chains relative to what is expected for brushes formed from the equivalent diblock copolymer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Polymer Grafted Janus Multi-Walled Carbon Nanotubes

We describe a novel and facile strategy to modify the surface of carbon nanotubes (CNTs) with two chemically different polymer brushes utilizing the grafting from technique. A [4 + 2] Diels Alder cycloaddition reaction was used to functionalize multi-walled carbon nanotubes (MWNTs) with two different precursor initiators, one for ring opening polymerization (ROP) and one for atom transfer radical polymerization (ATRP). The binary functionalized MWNTs were used for the simultaneous surface initiated polymerizations of different monomers resulting in polymer grafted MWNTs that can form Janus type structures under appropriate conditions. 1H NMR, FTIR and Raman spectra showed that the precursor initiators were successfully synthesized and covalently attached on the CNT surface. Thermogravimetric analysis (TGA) revealed that the grafted polymer content varies when different monomer ratios and polymerization times are used. The presence of an organic layer around the CNTs was observed through transmission electron microscopy (TEM). Differential scanning calorimetry (DSC) proved that the glass transition (Tg) and melting (Tm) temperatures of the grafted polymers are affected by the presence of the CNTs, while circular dichroism (CD) spectra indicated that the PLLA ahelix conformation remains intact.

77 NANOSCIENCE AND NANOTECHNOLOGY↗