Search NASA⌕ Search

Engineering topics

McCarthy, Tyler T.

Publications and source records attributed to McCarthy, Tyler T..

Magneto-transport study on Sn-rich Sn 1–x Ge x thin films enabled by CdTe buffer layer

α-Sn, generally known as gray tin, has attracted significant scientific interest due to its potential to host novel topological phases. Studying the transport properties of α-Sn thin films grown on the InSb substrate has been challenging, as the InSb substrate also significantly contributes to the transport properties. In this article, we report a novel approach to epitaxially grow α-Sn thin films on an InSb substrate with a resistive buffer layer of CdTe. Thin films of α–Sn 1–x Ge x (x = 0, 0.025) alloy of 15 nm thickness have been grown using molecular beam epitaxy. The high quality of the samples has been determined through high-resolution x-ray diffraction. The CdTe buffer layer has high resistance and acts as an insulating virtual substrate, which significantly suppresses contribution from InSb. Magnetotransport measurements show clear Shubnikov–de Hass oscillations in α–Sn 1–x Ge x (x = 0, 0.025) thin films. A change in oscillation frequency is observed upon alloying with Ge, implying a modification in the electronic structure and demonstrating the effectiveness of the CdTe buffer layer approach. Furthermore, this work provides a new approach that enables the electronic transport characterization of the α–Sn 1–x Ge x alloy system, which enables the study of the topological quantum states using electronic transport and their device applications.

36 MATERIALS SCIENCE↗

Molecular beam epitaxy growth and characterization of GePb alloys

Pb based group-IV alloys such as GePb have been gaining interest as a potential alternative for infrared detectors, quantum materials, and high-speed electronic devices. Challenges remain in their growth due to the extremely low solid solubility of Pb in the Ge–Pb system. This paper reports molecular beam epitaxy growth of GePb alloy thin films on Ge(100) substrates. Effusion cells of Ge and Pb are used to control the flux ratio independently. The optimal substrate temperature is found to be near the thermocouple temperature of 300 °C based on the characterization of the grown films using high-resolution x-ray diffraction. A large change in the Ge:Pb beam equivalent pressure ratio from 10:1 to 1:1 results in only a minimal increase of the Pb composition from 0.74% to 2.84% as estimated from Raman spectroscopy and Rutherford backscattering spectrometry. Furthermore, scanning electron microscopy images show a large volume of Pb islands on the surface that form into either long trapezoidal rods or uniform droplets, with increasing Pb flux and growth time the density of Pb islands increased.

36 MATERIALS SCIENCE↗

Monocrystalline 1.7-eV MgCdTe solar cells

Monocrystalline 1.7-eV Mg 0.13 Cd 0.87 Te/Mg x Cd 1-x Te (x > 0.13) double-heterostructure (DH) solar cells with varying Mg composition in the barrier layers are grown by molecular beam epitaxy. Furthermore, a Mg 0.13 Cd 0.87 Te/Mg 0.37 Cd 0.63 Te DH solar cell featuring abrupt interfaces between barriers and absorber and the addition of a SiO 2 anti-reflective coating demonstrates open-circuit voltage (V OC ), short-circuit current density (J SC ), fill factor (FF), and device active-area efficiencies up to 1.129 V, 17.3 mA/cm 2 , 77.7% and 15.2%, respectively. The V OC and FF vary oppositely with the Mg x Cd 1-x Te barrier height indicating an optimal design of the MgCdTe DHs as a tradeoff between carrier confinement and carrier transport. Temperature-dependent V OC measurements reveal the majority of carrier recombination in the devices occurs outside the DHs, in the a-Si:H hole-contact layer and at the interface between the a-Si:H layer and the Mg x Cd 1-x Te top barrier at room temperature. Simulation results for the device with the highest efficiency show that the p-type a-Si:H layer and Mg 0.37 Cd 0.63 Te top barrier contribute 1.3 mA/cm 2 and 2.4 mA/cm 2 J SC loss, respectively.

14 SOLAR ENERGY↗