Search NASA⌕ Search

Engineering topics

McCluskey, Matthew D.

Publications and source records attributed to McCluskey, Matthew D..

At least 19 records

Photoluminescence and Raman spectroscopy of wide bandgap semiconductors damaged by deep-UV laser irradiation

The effects of a pulsed, focused, deep-UV (4.66 eV) laser on wide and ultra-wide bandgap semiconductors were investigated with photoluminescence (PL) and Raman spectroscopy. Three semiconductor single crystals were studied: silicon carbide (6H-SiC), gallium nitride (GaN), and gallium oxide (β-Ga 2 O 3 ). Atomic emission lines from neutral Ga or Si were observed during the laser-damage process. For all three semiconductors, PL mapping (3.49 eV laser excitation) of the damaged material revealed visible emission bands in the 2.6–2.8 eV range, attributed to point defects. Raman spectra (2.33 eV excitation) showed a reduction in the Raman peak intensities in the damaged region, along with weak PL bands around 1.9–2.1 eV.

36 MATERIALS SCIENCE↗

Growth Phenomena and Bandgap Shift in Melt-Grown β-(In x Ga 1- x ) 2 O 3 Alloys

β-Ga 2 O 3 is an emerging ultra-wide bandgap semiconductor with great promise for power electronics and optoelectronics. Alloys in the In 2 O 3 -Ga 2 O 3 system are interesting for optoelectronic applications, particularly where bandgap tuning is desirable. Herein, β-(In x Ga 1- x ) 2 O 3 alloys with target compositions x = 0.025 or 0.10 are grown from the melt using the Czochralski and vertical gradient freeze techniques. Growth with 10 mol% In yields only small, needle-like crystals, while 2.5 mol% In allows growth of centimeter-sized single crystals. A substantial degree of indium segregation is unveiled by spatial measurements of lattice parameters and the bandgap. The bandgap decreases by a maximum of 0.28 eV in the case of the highest In content crystals. Z-contrast transmission electron microscopy confirms a solely octahedral coordination of In in the β-Ga 2 O 3 lattice. With indium concentrations higher than 2.5 mol%, samples contain micron-scale voids that impart a dark coloration. All measured crystals are electrically conductive, with carrier concentrations varying 10 16 –10 17 cm -3 depending upon the location of the sample in the growth. Lastly, a unique luminescence with unknown origin centered around 2.0 eV is revealed by photoluminescence spectroscopy.

36 MATERIALS SCIENCE↗

Photoluminescence mapping of laser-damaged β-Ga 2 O 3

Here, photoluminescence (PL) mapping was utilized to investigate damage in β-Ga 2 O 3 epilayers induced by 1064 nm laser pulses. The intensity and position of the intrinsic UV band were determined and plotted as a false-color image. Two types of damage were identified: circular damage and damage cracks. Circular damage shows lower UV PL intensity than the surrounding material with color centers in a “halo” around the damaged region. Damage cracks are aligned with the a and c axes and show higher PL intensity than undamaged material. Defects in the as-grown material were revealed by shifts in the UV band energy.

36 MATERIALS SCIENCE↗

Electron irradiation effects on the optical properties of Hf- and Zn-doped β -Ga 2 O 3

Optical and electrical properties of Hf- and Zn-doped β-Ga 2 O 3 samples, which are n-type and insulating, respectively, were altered via high-energy electron irradiation at 2.5 or 0.5 MeV. The β-Ga 2 O 3 :Hf samples irradiated with 2.5 MeV electrons experienced a color change from blue to yellow and a large drop in conductivity, attributed to the creation of gallium vacancies, which compensate donors. This irradiation resulted in the absence of free carrier absorption and the presence of Cr 3+ photoluminescence (PL). PL mapping prior to irradiation revealed optically active ZnO precipitates that formed during the growth of β-Ga 2 O 3 :Zn. These precipitates have a 384 nm (3.23 eV) stacking fault emission in the core; in the outer shell of the precipitate, the PL blue-shifts to 377 nm (3.29 eV) and a broad defect band is observed. After 0.5 MeV electron irradiation, the defect band broadened and increased in intensity. The blue PL band (435 nm) of β-Ga 2 O 3 was enhanced for both Hf- and Zn-doped samples irradiated with 0.5 MeV. This enhancement is correlated with an increase in oxygen vacancies.

36 MATERIALS SCIENCE↗

Phase Transition of Heptane under Pressure

A solid-to-solid phase transition was discovered in n-heptane with an onset at a pressure of 1.7 ± 0.1 GPa, evidenced by a discontinuity in the pressure–volume equation of state obtained from synchrotron X-ray diffraction experiments conducted at room temperature. The phase transition also resulted in discontinuous shifts of vibrational peaks in the infrared spectra. No additional phase transitions were detected up to 10 GPa, contradicting an earlier claim of a phase transition at 3 GPa. Furthermore, the hydrostatic limit of heptane in a diamond anvil cell was estimated to be 3.5 GPa. Above that pressure, the stress state is not well-defined, which may explain prior reports of a phase transition at 7.5 GPa.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Melt-grown semi-insulating Mn:β-Ga 2 O 3 single crystals exhibiting unique visible absorptions and luminescence

In this study, several acceptor dopants have been explored in β-Ga 2 O 3 to produce semi-insulating substrates and epitaxial films. Fe and Mg make up the majority of research thus far; however, other transition metals provide potential alternatives for optimized performance. β-Ga 2 O 3 bulk single crystals were grown by the Czochralski and vertical gradient freeze methods with a nominal dopant concentration of 0.25 at. % Mn. Ultraviolet-visible-near infrared spectroscopy and photoluminescence revealed polarization- and orientation-dependent optical absorptions (pleochroism) coupled with an orange luminescence. All samples were electrically insulating, on the order of 10 9 –10 11 ohm cm at room temperature, indicative of acceptor doping. Actual dopant concentrations of the intentionally doped transition metal and background impurities were determined via glow discharge mass spectrometry, indicating the macroscale segregation behavior. High-temperature resistivity measurements indicated an experimental acceptor level of 1.7 ± 0.2 eV. Hydrogenation of samples resulted in an increase in the orange luminescence and O–H stretching modes observable in the infrared spectrum. Density functional theory calculations were performed to determine the likely site-occupancy and acceptor level of Mn in the bandgap.

36 MATERIALS SCIENCE↗

Resonant interactions involving local vibrational modes in crystals

When an impurity with a light mass is inserted into a crystal, it can undergo a high-frequency oscillation referred to as a local vibrational mode (LVM). A Fermi resonance may occur between the LVM and lower-frequency modes of the defect. The LVM may also interact with phonons or the electromagnetic field. Understanding these interactions can help model and control diffusion, defect reactions, and thermal conductivity. LVMs have been probed in semiconductors using pressure and alloying as experimental parameters, resulting in anticrossing between localized and extended vibrational modes. Furthermore, these types of vibrational interactions could play an important role in the stability and thermal properties of organic–inorganic hybrid semiconductors. The coupling between an LVM and electromagnetic wave yields an “LVM polariton,” an excitation that has significant vibrational and electric-field amplitudes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Photoluminescence of Cr 3+ in β-Ga 2 O 3 and (Al 0.1 Ga 0.9 ) 2 O 3 under pressure

The effects of pressure on single crystals of Cr-doped gallium oxide (β-Ga 2 O 3 :Cr 3+ ) and aluminum gallium oxide [(Al 0.1 Ga 0.9 ) 2 O 3 ] were examined by measuring the wavelength shift in the spectral R lines. Photoluminescence (PL) spectra of these materials were collected from samples in diamond anvil cells at pressures up to 9 GPa. The β-Ga 2 O 3 :Cr 3+ R lines were found to shift linearly under hydrostatic pressure. The (Al 0.1 Ga 0.9 ) 2 O 3 R lines also show a linear shift but the R 1 line shifted less than for β-Ga 2 O 3 :Cr 3+ . The ratio of R 2 to R 1 peak areas vs pressure is dominated by nonradiative recombination. X-ray diffraction measurements of (Al 0.1 Ga 0.9 ) 2 O 3 indicate that its equation of state is similar to that of β-Ga 2 O 3 . β-Ga 2 O 3 :Cr 3+ was examined under non-hydrostatic conditions by using mineral oil as a pressure transmitting medium. Similar to the case in ruby, the R 1 line is much more sensitive to non-hydrostatic stress than R 2 . Spatially resolved PL of a sample at 8 GPa in mineral oil showed significant variations in the R 1 emission wavelength. Furthermore, these results suggest that the R 1 line can serve as a sensitive probe of alloy composition and non-hydrostatic stress, while the R 2 line is insensitive to these perturbations.

36 MATERIALS SCIENCE↗

Persistent optical phenomena in oxide semiconductors

The interaction of transparent oxide semiconductors with light is critically important for a range of applications. Persistent effects could be exploited for holographic memory or optically defined circuits. Conversely, they may also be detrimental to device operation. Large, room-temperature persistent photoconductivity (PPC) was discovered in strontium titanate (SrTiO 3 , STO) after annealing in a hydrogen-containing atmosphere. Barium titanate (BaTiO 3 , BTO), a ferroelectric material, was recently found to also exhibit PPC. Room-temperature photodarkening was observed in Cu-doped gallium oxide (β-Ga 2 O 3 ) after exposure to sub-bandgap light. Hydrogen is believed to play a central role in these persistent phenomena. In the proposed model, a photon excites substitutional hydrogen (a proton inside an oxygen vacancy), making the defect unstable. The proton leaves and binds to a host oxygen atom, forming an O-H bond that is observed with infrared spectroscopy. Here, an oxygen vacancy is left behind. Because oxygen vacancies in STO and BTO are shallow donors, this process results in PPC. In β-Ga 2 O 3 :Cu, however, the oxygen vacancy neighbors a Cu acceptor. In that case, photoexcitation results in the rare Cu 3+ state, which absorbs visible light. The effect can be “erased” by annealing at 300-400°C.

Annealing↗

Photoluminescence spectroscopy of Cr 3+ in β-Ga 2 O 3 and (Al 0.1 Ga 0.9 ) 2 O 3

Alloying β-Ga 2 O 3 with Al 2 O 3 to create (Al x Ga 1–x ) 2 O 3 enables ultra-wide bandgap materials suitable for applications deep into ultraviolet. In this work, photoluminescence (PL) spectra of Cr 3+ were investigated in monoclinic single crystal β-Ga 2 O 3 , and 10 = mol. % Al 2 O 3 alloyed with β-Ga 2 O 3 , denoted β-(Al 0.1 Ga 0.9 ) 2 O 3 or AGO. Temperature-dependent PL properties were studied for Cr 3+ in AGO and β-Ga 2 O 3 from 295 to 16 K. For both materials at room temperature, the red-line emission doublet R 1 and R 2 occurs at 696 nm (1.78 eV) and 690 nm (1.80 eV), respectively, along with a broad emission band at 709 nm (1.75 eV). Here, the linewidths for AGO are larger for all temperatures due to alloy broadening. For both materials, the R-lines blue-shift with decreasing temperature. The (lowest energy) R 1 line is dominant at low temperatures due to the thermal population of the levels. For temperatures above ~50 K, however, the ratio of R 2 to R 1 peak areas is dominated by nonradiative combination.

36 MATERIALS SCIENCE↗

Selectively patterned Mg-doped GaN by SiN x -driven hydrogen injection

In this work, we demonstrate a method to achieve selectively patterned Mg-doped GaN layers using hydrogen drive-in through plasma-enhanced chemical vapor deposition (PECVD) silicon nitride (SiN x ) films. Activated Mg-doped GaN layers were selectively deactivated by patterned PECVD SiN x films with low-temperature annealing and showed high-resistive behavior. Spatially resolved photoluminescence measurements were used to optically verify the deactivation of Mg acceptors and showed distinct features corresponding to activated and deactivated Mg in GaN. The method suggested here provides a simple and effective method to achieve patterned Mg-doped GaN regions without thermal and plasma damage, which could cause degradation of device performance. The proposed method could provide a way to achieve future high-performance GaN lateral and vertical devices that rely on laterally patterned doping.

42 ENGINEERING↗

Photoluminescence and Raman mapping of β-Ga 2 O 3

Semi-insulating single crystal β-Ga 2 O 3 is becoming increasingly useful as a substrate for device fabrication. Fe doping is a method for producing such substrates. Along with Fe dopants, β-Ga 2 O 3 :Fe also contains Cr 3+ . Photoluminescence (PL) emission peaks at 690 nm (1.80 eV) and 696 nm (1.78 eV), as well as a broad feature around 709 nm (1.75 eV), are observed in β-Ga 2 O 3 :Fe. PL mapping of the 690 nm emission showed high and low intensity bands due to impurity striations introduced during crystal growth. PL mapping also revealed surface defects showing broad emissions around 983 nm (1.26 eV) and 886 nm (1.40 eV) that were spatially localized, occurring at discrete spots on the sample surface. Raman mapping of an 886 nm emission center revealed peaks at 2878 and 2930 cm -1 , consistent with an organometallic or hydrocarbon compound. Raman mapping of the 983 nm center showed a peak at 2892 cm -1 . Bright UV emission centers showed Raman peaks at 2910 and 2968 cm -1 , which are attributed to Si-CH 3 groups that may originate from silica polishing compounds or annealing in a silica ampoule.

36 MATERIALS SCIENCE↗

Zinc–hydrogen and zinc–iridium pairs in β-Ga 2 O 3

Zinc-doped monoclinic gallium oxide (β-Ga 2 O 3 :Zn) has semi-insulating properties that could make it a preferred material as a substrate for power devices. In this work, infrared and UV/Visible spectroscopy were used to investigate the defect properties of bulk β-Ga 2 O 3 :Zn crystals. As-grown crystals contain a single O-H stretching mode at 3486.7 cm -1 due to a neutral ZnH complex. A deuterium-annealed sample displays the corresponding O-D stretching mode at 2582.9 cm -1 , confirming the O-H assignment. A strong Ir 4+ electronic transition at 5147.6 cm -1 is also observed, along with sidebands attributed to ZnIr pairs. These sidebands show distinct differences compared with Mg-doped samples; most importantly, several peaks are attributed to Ir 4+ paired with a Zn on the tetrahedral Ga(I) site. Annealing under an oxygen atmosphere produced insulating material with a resistance above 1 TΩ.

36 MATERIALS SCIENCE↗

Classification of Semiconductors Using Photoluminescence Spectroscopy and Machine Learning

Photoluminescence spectroscopy is a nondestructive optical method that is widely used to characterize semiconductors. In the photoluminescence process, a substance absorbs photons and emits light with longer wavelengths via electronic transitions. This paper discusses a method for identifying substances from their photoluminescence spectra using machine learning, a technique that is efficient in making classifications. Neural networks were constructed by taking simulated photoluminescence spectra as the input and the identity of the substance as the output. Here, six different semiconductors were chosen as categories: gallium oxide (Ga 2 O 3 ), zinc oxide (ZnO), gallium nitride (GaN), cadmium sulfide (CdS), tungsten disulfide (WS 2 ), and cesium lead bromide (CsPbBr 3 ). The developed algorithm has a high accuracy (>90%) for assigning a substance to one of these six categories from its photoluminescence spectrum and correctly identified a mixed Ga 2 O 3 /ZnO sample.

47 OTHER INSTRUMENTATION↗

Gallium vacancy formation in oxygen annealed β-Ga 2 O 3

Here, the formation and character of gallium vacancies (V Ga ) and their complexes in near surface and bulk regions of single crystal β-Ga 2 O 3 were explored using unintentionally doped single crystals grown by the Czochralski method. As-grown and O 2 annealed (up to 1550 °C) samples were investigated using positron annihilation spectroscopy (PAS) to study the top 0.05–6 μm, and also current–voltage measurements and infrared (IR) spectroscopy, with hydrogenated samples to probe V Ga , to study the bulk. After annealing in O 2 > 1000 °C, the β-Ga 2 O 3 resistivity begins increasing, up to ~10 9 Ω cm for 1550 °C treatment, with the top 0.5 mm being many orders of magnitude more resistive. PAS measurements of the top 6 μm (S values) and very near surface 200 nm (diffusion length, L) indicate differential behavior as a function of peak annealing temperature. At least four temperature regimes of behavior are described. V Ga are present in the bulk after growth, but considerable changes occur upon annealing at a temperature ≈1000 °C, where L and S decrease simultaneously, suggesting an increasing defect concentration (L) but a decreasing defect volume (S). Annealing at a temperature ≈1400 °C increases S again, showing an increasing volume concentration of V Ga , with IR absorption showing a large signature of V Ga -2H, indicative of increased V Ga formation that was not present when annealing at a temperature ≈1000 °C. These results suggest that defect changes from annealing in oxygen are depth dependent, and that V Ga configuration may not be the same near the oxygen-exposed surface of the sample and in the bulk.

74 ATOMIC AND MOLECULAR PHYSICS↗

Localized UV emitters on the surface of β-Ga 2 O 3

Abstract Monoclinic gallium oxide (β-Ga 2 O 3 ) is attracting intense focus as a material for power electronics, thanks to its ultra-wide bandgap (4.5–4.8 eV) and ability to be easily doped n -type. Because the holes self-trap, the band-edge luminescence is weak; hence, β-Ga 2 O 3 has not been regarded as a promising material for light emission. In this work, optical and structural imaging methods revealed the presence of localized surface defects that emit in the near-UV (3.27 eV, 380 nm) when excited by sub-bandgap light. The PL emission of these centers is extremely bright—50 times brighter than that of single-crystal ZnO, a direct-gap semiconductor that has been touted as an active material for UV devices.

36 MATERIALS SCIENCE↗

Enhancement of the ultraviolet photoluminescence of ZnO films: Coatings, annealing, and environmental exposure studies

To realize the many potential applications of ZnO films, it is vital to produce films with high optical quality that exhibit strong UV luminescence. By combining annealing at an optimal temperature followed by the deposition of a coating, one can achieve a significant enhancement of photoluminescence (PL). The effectiveness of the coating over time is a crucial point to be considered. Three types of coating materials were investigated: MgO, SiO 2 , and Al 2 O 3 . Due to its strong bond energy, MgO was found to be the most effective coating material for passivation of the surfaces of the ZnO films; SiO 2 was the second best. The UV-PL intensity of MgO coated ZnO was found to increase by a factor of 52 relative to an uncoated film. The effectiveness of the coatings exhibited a linear correlation with their bond energies and is discussed in terms of competing mechanisms to surface passivation such as the adsorption of OH-groups; these can act as surface traps and diminish the UV-PL intensity. Annealing at 900 °C prior to the deposition of the coating was found to be an important step in realizing the optimal performance of the coating due to the reduction of Zn interstitials accompanied by improved crystallinity. Exposure to the environment, up to 294 days, results in the degradation of the UV-PL of the MgO coated film; this effect was not observed for the film coated with SiO 2 . This effect is discussed in terms of the strong reactivity of MgO with environmental contaminants from the OH-groups.

36 MATERIALS SCIENCE↗

Surface Effects on Pyrene Luminescence Excitation

Pyrene is a polycyclic aromatic hydrocarbon with fluorescence in the 370-400 nm range. The optical properties of pyrene deposited on different substrates were investigated from experimental and theoretical points of view. In contrast to prior studies of surface-enhanced fluorescence, in this work all substrates were semiconductors or insulators. Experimentally, the intensity of photoluminescence (PL) and PL excitation (PLE) spectra were investigated. PLE spectra of pyrene’s monomer emission show that the intensities of the two main absorption peaks vary according to the chosen substrate. Here, calculations for pyrene on zinc sulfide (ZnS) and surface-oxidized diamond suggest that this connection arises from the alignment of the pyrene electronic levels relative to the band edges of the substrate. The absorption peak at 272 nm (4.56 eV) is shown to depend on the HOMO-1→LUMO orbital contribution while the 335 nm (3.70 eV) peak depends upon the HOMO→LUMO transition. When the HOMO-1 level falls inside the substrate valence band, as in the case of ZnS, there is significant hybridization of the molecular state with surface states that causes an enhancement of the 272 nm peak. For pyrene on diamond, however, the HOMO-1 level falls in the substrate bandgap, leading to negligible hybridization and thus no enhancement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗