Search NASA⌕ Search

Engineering topics

McCormick, Robert L. (ORCID:0000000314627165)

Publications and source records attributed to McCormick, Robert L. (ORCID:0000000314627165).

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Conversion of Wet Waste to Sustainable Aviation Fuel and Chemical Intermediates via Catalytic Upgrading

Wet waste is a low-cost, abundant feedstock capable of displacing significant amounts of domestic petrofuel and petrochemical consumption. We present a sequential biochemical-thermochemical pathway to upgrade wet waste into hydrocarbon sustainable aviation fuel blendstock and chemical intermediates with near-zero or net-negative life-cycle CO2 emissions. Waste is initially upgraded to carboxylic acids via arrested anaerobic digestion, then catalytically converted to hydrocarbons via sequential heterogeneous catalytic ketonization, cyclization, and hydrodeoxygenation. We will discuss kinetics, durability, and reactor design of key catalytic processes, as well as applicability of final products to targeted applications.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗
DOE OSTI2023

Diesel Particulate Filter Durability Performance Comparison Using Metals Doped B20 vs. Conventional Diesel Part II: Chemical and Microscopic Characterization of Aged DPFs

This project's objective was to generate experimental data to evaluate the impact of metals doped B20 on diesel particle filter (DPF) ash loading and performance compared to that of conventional petrodiesel. The effect of metals doped B20 vs. conventional diesel on a DPF was quantified in a laboratory controlled accelerated ash loading study. The ash loading was conducted on two DPFs - one using ULSD fuel and the other on B20 containing metals dopants equivalent to 4 ppm B100 total metals. Engine oil consumption and B20 metals levels were accelerated by a factor of 5, with DPFs loaded to 30 g/L of ash. Details of the ash loading experiment and on-engine DPF performance evaluations are presented in the companion paper (Part I). The DPFs were cleaned, and ash samples were taken from the cleaned material. X-ray Fluorescence (XRF), X-Ray Photoelectron Spectroscopy (XPS) and X-Ray Diffraction (XRD) were conducted on the ash samples. Core samples were taken from the cleaned DPF and were subjected to scanning electron microscope energy dispersive x-ray spectroscopy (SEM-EDS) and XRF analysis. A comparison of the data from the two DPFs is presented. The XRD and XPS analysis showed that the compounds present in the ash from the two DPFs were nearly identical, though differing in concentrations. CaSO4 was the biggest component of the ash from both DPFs. The metals doped B20 fuel resulted in ash with similar characteristics to that deposited by the lube oil and did not appear to have any deleterious physical effects on the DPF substrate (did not penetrate the substrate).

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗
DOE OSTI2023

Diesel Particulate Filter Durability Performance Comparison Using Metals Doped B20 vs. Conventional Diesel Part I: Accelerated Ash Loading and DPF Performance Evaluation

The project objective was to generate experimental data to evaluate the impact of metals doped B20 on DPF ash loading and performance compared to that of conventional petrodiesel. Accelerated ash loading was conducted on two DPFs - one exposed to regular diesel fuel and the other to B20 containing metal dopants equivalent to 4 ppm B100 total metals (currently total metals are limited to 10 ppm in ASTM D6751, the standard for B100). Periodic performance evaluations were conducted on the DPFs at 10 g/L ash loading intervals. After the evaluations at 30 g/L, the DPF was cleaned with a commercial DPF cleaning machine and another round of DPF evaluations were conducted. A comparison of the effect of ash loading with the two fuels and DPF cleaning is presented. The metals doped B20 fuel resulted in ash that was similar to that deposited when exposed to ULSD (lube oil ash) and exhibited similar ash cleaning removal efficiency. Metals doped B20 resulted in faster ash accumulation within the DPF, as expected, but did not appear to have a negative effect on DPF pressure drop or regeneration rates (up to 30 g/L of ash) or exhibit deleterious physical effects on the DPF substrate.

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗
DOE OSTI2023

Modeling Ethanol-Blend Fuel Sprays under Direct-Injection Spark-Ignition Engine Conditions

Computational modeling of fuel-injection and fuel-impingement processes was carried out to provide insight into previous experimental results obtained from a direct-injection spark-ignition research engine operated with various ethanol and aromatic fuel blends. Seven model fuels were evaluated using both single- and split-injection strategies. Model results showed that droplet vaporization enriched the concentrations of aromatic species in the liquid phase, especially those with low vapor pressure, and ethanol-containing fuels altered droplet sizes and led to increased liquid-phase mass in the cylinder. For the spray-modeling conditions studied, most of the injected fuel remained in the liquid phase, which would be expected to result in more fuel impingement on cylinder or piston surfaces. Fuel impinging on lower cylinder-temperature surfaces was found to create wall films that could interact with the piston during the compression stroke. Fuel impinging on hotter piston-temperature surfaces vaporized more readily, but for fuels with high ethanol and aromatic content, wall films remained and were highly concentrated with lower vapor pressure and aromatic compounds. These films could lead to pool fires during combustion and therefore significant particulate matter emissions.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗
DOE OSTI2022

Chemical Kinetics Underlying the Sooting Tendency and Auto-Ignition Characteristics of Linear, Branched, and Cyclic Ether Compounds

Biofuels present opportunities for improving the performance and reducing emissions from internal combustion engines by incorporating oxygenated functional groups to the fuels. Among various oxygenates, ethers have been recognized as promising candidates for an alternative to conventional diesel fuel owing to their higher reactivity and lower sooting tendency. The detailed guidelines for designing ethers, however, have not been fully discussed, even though their combustion characteristics are sensitive to the molecular structure. This study was devoted to exploring the structure-property relationships, particularly focusing on the cetane number and yield sooting index, using five linear, branched, and cyclic ethers: di-amyl-ether, 4-butoxy-heptane, 3,3-dimethyl-oxetane, 2-ethyl-4-methyl-1,3-dioxolane, and 2-isopropyl-4-methyl-1,3-dioxolane. First, we examined the chemical kinetics underlying the sooting tendency of the test fuels. The combustion product distribution was measured from flow reactor experiments at 750-1100 K, F=3, at atmospheric pressure. As a result, it was revealed that the sooting tendency is closely related to the size of hydrocarbon intermediates in the high-temperature regime (>1000 K); that is, larger hydrocarbons lead to more soot precursor formation. The underlying chemistry determining the size of the hydrocarbons from the tested fuels was analyzed using reaction pathway analysis and quantum mechanics calculations, which showed that the branched and cyclic ether structures form abundant C3-C4 compounds. Moreover, the auto-ignition characteristics of the test fuels were studied using the flow reactor at low-temperature (400-700 K) and F=1. We found a clear difference in the combustion-product distribution from high and low reactivity fuels, which was then correlated to the systematic analysis of the key reaction energy barriers with the varying molecular structure.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗
DOE OSTI2022

Measuring Critical Fuel Properties for Simulations to Accelerate Fuel Qualification

NREL's sustainable aviation fuel (SAF) research in the area of fuel properties and end use is focused on accelerating SAF development and deployment. This will be achieved by close collaboration with BETO program researchers on fuel property measurement and development of structure-property relationships. Additionally, fuel properties measured at often extreme engine operating conditions will be measured, and will be used as inputs to exascale ready simulations of aviation combustion turbines to reveal impacts of properties on turbine operation. This research will potentially lead to a widening of the allowable fuel property range for SAF, expanding SAF production process options and production volumes.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Reducing Sample Loss in Measurement of Heat of Vaporization of Ethanol/Gasoline Blends by Differential Scanning Calorimetry/Thermogravimetric Analysis

Higher gasoline Heat of Vaporization (HOV) can enable higher compression-ratio direct injection spark ignition engines by providing evaporative cooling that effectively increases fuel knock resistance. Methods to directly measure this fuel property in complex gasoline samples are not well developed. The objective of the present study was to further improve a Differential Scanning Calorimetry/Thermogravimetric Analyzer (DSC/TGA) method to measure the total and partial HOV of gasoline. Ten market gasoline samples were chosen to have a wide range of properties to assess the method's capability across the entire volatility range with an emphasis on understanding how well the method captures the initial 10 percent (%) of sample evaporation and how much sample is left unevaporated at the end of the experiment. Modifications to the sample preparation/introduction method as well as to the instrument itself were made to reduce initial sample losses which included measurements of the HOV at 10 degrees C and 5 degrees C (in a cold chamber) as well as under (uncontrolled) ambient conditions. Experimental results from the DSC/TGA were compared to calculated total HOV results based on Detailed Hydrocarbon Analysis (DHA). Results from the two methods agreed very well with the difference being 5% or less in almost every case. In addition, the repeatability of the method was investigated by analyzing samples in triplicate at the three temperatures investigated. One valuable conclusion from the study was that the lower temperatures of 10 degrees C and 5 degrees C enabled more reproducible measurements for both total and partial HOV. This improved precision may be caused by the fact that temperature control in the cold chamber was more reliable than the ambient laboratory temperature control. Additionally, cold chamber experiments, due to ergonomic limitations, did not allow for the use of a lid on the sample pan. The reproducibility of the evaporation rate was found to be highly dependent on the pan/lid fit which can vary significantly such that elimination of the lid improved measurement precision while operation at sub-ambient temperature slowed the evaporation rate. Results detailing sample preparation and instrument modifications as well as a detailed comparison of total and partial HOV results are presented.

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗
DOE OSTI2021

Impacts of Biofuel Blending on MCCI Ignition Delay with Review of Methods for Defining Cycle-by-Cycle Ignition Points from Noisy Cylinder Pressure Data: Preprint

Conventional diesel combustion, also known as Mixing-Controlled Compression Ignition (MCCI), is expected to be the primary power source for medium- and heavy-duty vehicles for decades to come. Displacing petroleum-based ultra-low-sulfur diesel (ULSD) as much as possible with low-net-carbon biofuels will become necessary to help mitigate effects on climate change. Neat biofuels may have difficulty meeting current diesel fuel standards but blends of 30% biofuel in ULSD show potential as ‘drop-in’ fuels. These blends must not make significant changes to the combustion phasing of the MCCI process if they are to be used interchangeably with neat ULSD. An important aspect of MCCI phasing is the ignition delay (ID), i.e. the time between the start of fuel injection and the initial premixed autoignition that initiates the MCCI process. Bench experiments can evaluate the expected ignition delay of a fuel via cetane number (CN) or alternative methods such as the indicated cetane number (ICN); however, neither CN nor ICN correlate perfectly with the ignition delay measured in actual engine experiments. Furthermore, there is no standardized methodology on how to quantify MCCI ignition delay from engine cylinder pressure measurements, creating difficulties in cross-study comparison. In this study, several engine ignition delay calculation methods are evaluated for robustness in deriving ignition delay on both a cycle-averaged and cycle-to-cycle basis. Eight biofuel blends with varying ICN, oxygen concentration and other fuel properties were used to study the different methods. This yields a thorough analysis of how certain biofuel blends affect ignition delay and the entire MCCI process, as well as a thorough evaluation of the differences between the ID calculation methods. Many of these methods are equally valid, but the choice of method has a significant impact on the resulting ID, which must be carefully considered when evaluating results across multiple studies.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Fuel Property Effects of a Broad Range of Potential Biofuels on Mixing Control Compression Ignition Engine Performance and Emissions

Conventional diesel engines will continue to hold a vital role in the heavy- and medium-duty markets for the transportation of goods along with many other uses. The ability to offset traditional diesel fuels with low-net-carbon biofuels could have a significant impact on reducing the carbon footprint of these vehicles. A prior study screened several hundred candidate biofuel blendstocks based on required diesel blendstock properties and identified 12 as the most promising. Eight representative biofuel blendstocks were blended at a 30% volumetric concentration with EPA certification ultra-low-sulfur diesel (ULSD) and were investigated for emissions and fuel efficiency performance. This study used a single cylinder engine (based on the Ford 6.7L engine) using Conventional Diesel Combustion (CDC), also known as Mixing Control Compression Ignition (MCCI). The density, cetane number, distillation curve and sooting tendency (using the yield sooting index method) of the fuels were measured. Start of injection (SOI) timing and exhaust gas recirculation (EGR) sweeps were conducted at three separate speed-load operating points to examine fuel effects on the NOX/soot and NOX/efficiency trade-offs as well as to evaluate EGR tolerance. The results show that the biofuel blends all reduced NOX and soot emissions without penalty to engine efficiency, even improving efficiency for some of the blends at certain points, with one particular blend of polyoxymethylene ethers (POMEs) improving efficiency at all points while drastically reducing soot by 79%.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

A Perspective on Biomass-Derived Biofuels: From Catalyst Design Principles to Fuel Properties

The hazards to health and the environment associated with the transportation sector include smog, particulate matter, and greenhouse gas emissions. Conversion of lignocellulosic biomass into biofuels has the potential to provide significant amounts of infrastructure-compatible liquid transportation fuels that reduce those hazardous materials. However, the development of these technologies is inefficient, due to: (i) the lack of a priori fuel property consideration, (ii) poor shared vocabulary between process chemists and fuel engineers, and (iii) modern and future engines operating outside the range of traditional autoignition metrics such as octane or cetane numbers. In this perspective, we describe an approach where we follow a “fuel-property first” design methodology with a sequence of (i) identifying the desirable fuel properties for modern engines, (ii) defining molecules capable of delivering those properties, and (iii) designing catalysts and processes that can produce those molecules from a candidate feedstock in a specific conversion process. Computational techniques need to be leveraged to minimize expenses and experimental efforts on low-promise options. This concept is illustrated with current research information available for biomass conversion to fuels via catalytic fast pyrolysis and hydrotreating; outstanding challenges and research tools necessary for a successful outcome are presented.

BIOMASS FUELS↗