Search NASA⌕ Search

Engineering topics

McCormick, Robert L.

Publications and source records attributed to McCormick, Robert L..

27 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Global Ethanol-Blended-Fuel Vehicle Compatibility Study

The objective of this study is to understand the impact of ethanol-blended fuel at various blending levels (10%, 15%, and 20% vol.) on "in-operation" vehicles built to differing emissions and manufacturing standards around the world. The study focuses on vehicles used in Canada, China, India, Indonesia, Japan, South Korea, and Mexico. Historical experience in the United States and Brazil informs the analysis. The primary study question is: Are vehicles in targeted countries physically and operationally compatible with ethanol blended fuel? For a fuel to be compatible with a vehicle, the fuel must perform its function as part of the integrated fuel-vehicle system, meaning: the car should start easily and drive normally, the fuel should not cause catastrophic fuel system leaks, the fuel should not cause corrosion or degradation of any engine or fuel system components (including emissions control components). The history of E10 use in the United States, beginning in 1978, was evaluated and shows no reliability or operability issues for cars dating back to pre-emissions-control times -- and likely included many cars manufactured in the 1960s. This strongly supports the contention that fuel chemistry and property differences between E0 and E10 are so small that any car made to international standards in the last 50 years will have a very high probability of being fully compatible with E10. This conclusion is supported by the experience in Brazil in the 1970s, where E10 was also introduced, and ethanol blending for conventional cars rapidly ramped up to even higher blend levels. A limited number of fuel system and component manufacturers supply the global market, including Bosch, Continental, Denso, Delphi, and Visteon. To reduce complexity, ethanol-compatible materials began to be integrated in fuel system designs globally. Fuel systems evolved over the following decades to incorporate ethanol-compatible materials with core subsystem families, such as in-tank fuel pumps used across several global vehicle original equipment manufacturers (OEMs). A similarly compelling case can be made that all cars at the Tier 1 (or equivalent) emissions-control technology level or higher are fully compatible with E15 blends, based on the data evaluated by the U.S. Environmental Protection Agency (EPA) and Ricardo in 2010. For cars at this technology level, the minor differences in fuel chemistry and properties between E10 and E15 are not significant. For E20, studies are not as extensive but are still highly significant. A long-term durability study conducted on mileage accumulation dynamometers presents convincing evidence that Tier 2 technology level cars have materials of construction and engine control authority for compatibility with E20, although this conclusion is not as strong as those drawn for E10 and E15, which are also partly based on real-world experience.

09 BIOMASS FUELS↗
DOE OSTI2021

A Review and Perspective on Particulate Matter Indices Linking Fuel Composition to Particulate Emissions from Gasoline Engines

Particulate matter (PM) indices - those linking PM emissions from gasoline engines to the composition and properties of the fuel - have been a topic of significant study over the last decade. It has long been known that fuel composition has a significant impact on particulate emissions from gasoline engines. Since gasoline direct injection (GDI) engines have become the market-leading technology, this has become more significant because the evaporative behavior of fuel increases in importance. Several PM indices have been developed to provide metrics describing this behavior and correlating PM emissions. In this article, 16 different PM indices are identified and collected - to the authors' knowledge, all of the indices are available at the time of writing. The indices are reviewed and discussed in the context of the information required to calculate them, as well as their utility. Additionally, the authors believe that there is a need for indices that provide both a detailed and robust correlation, as well as those that are less sophisticated yet sufficient for specific use cases. Future research is suggested to guide the technical community toward improvements in the indices' methods and equations for both high and low fidelity and high and low time investment.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Top 13 Blendstocks Derived from Biomass for Mixing-Controlled Compression-Ignition (Diesel) Engines: Bioblendstocks with Potential for Decreased Emissions and Improved Operability

Reducing the impacts of medium- and heavy-duty (MD/HD) ground transportation can be enabled by fuel-engine combinations that use lower compression ignition liquid fuels and reduce criteria pollutant emissions. Fuels and blendstocks combined with advanced engine technologies could reduce the cost of ownership and the emission of pollutants, including soot, nitrogen oxides (NOx) and greenhouse gases (GHGs), from MD/HD vehicles. This report describes the evaluation and screening of MD/HD mixing-controlled compression ignition (MCCI) biofuel candidates for further development and commercialization. The report is aimed at 1) biofuel researchers looking to better understand options to reduce criteria pollutant and GHG emissions while maintaining efficiency and meeting requirements for engine operability and 2) engine researchers who want to evaluate biofuels that meet diesel fuel properties for their impact on conventional and advanced diesel combustion strategies.

09 BIOMASS FUELS↗
DOE OSTI2020

Understanding how chemical structure affects ignition-delay-time $\phi$-sensitivity

$\phi$-sensitivity is the change in ignition delay time (IDT) with respect to the fuel-to-air equivalence ratio ($\phi$). High $\phi$-sensitivity is a desirable fuel property for applications in advanced compression ignition and multi-mode engine designs. Understanding how $\phi$-sensitivity depends on chemical structure is essential for selecting promising biofuels from the ever-growing list of proposed candidates. Here, we investigate the effect of chemical structure on $\phi$-sensitivity with experiment, simulation, and theory. Experimental Advanced Fuel Ignition Delay Analyzer (AFIDA) measurements for 2,4-dimethylpentane and diisopropyl ether provide evidence that branching and functional groups strongly impact $\phi$-sensitivity. Further insights into this dependence are obtained with 0-D kinetic simulations with existing mechanisms for n-pentane, diethyl ether, 3-pentanone, n-heptane, 2-methylhexane, 2,4-dimethylpentane, and 2,2,3-trimethylbutane. Quantum mechanical (QM) G4 calculations of low-temperature reactions help explain the observed experimental and simulation trends. Specifically, these QM calculations provide theoretical estimates of the ketohydroperoxide (KHP) dissociation rates, the HO 2 formation rates from peroxy radical (ROO), and the “cross-over” temperatures, i.e., the temperature at which ROO dissociation is favored compared to hydroperoxyl radical (QOOH) formation. Each of these reaction rates is compared to the n-alkane reference point to determine the impact of branching and different functional groups. Although kinetic mechanisms typically assume that KHP dissociation rates are invariant of chemical environment, our QM results suggest that this rate can span a range of roughly two orders of magnitude. We also discuss the importance of including the peroxy-hydroperoxy (OO-OOH) hydrogen transfer reaction for branched ethers. Finally, the insights gained assist in proposing a highly $\phi$-sensitive compound, namely, isopropyl propyl ether.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Re-Additization of Commercial Biodiesel Blends During Long-Term Storage

Commercial biodiesel blends representative of the U.S. market were aged following procedure ASTM D4625, Standard Test Method for Middle Distillate Fuel Storage Stability at 43°C (110°F), with periodic monitoring of fuel properties indicative of oxidation. The oxidation stability—or oxidation reserve expressed as Rancimat induction period (IP)—gradually decreased from its initial value, as expected. At a predetermined IP threshold, an antioxidant was used to restore IP to the ASTM D7467 specification minimum of 6 six hours, referred to as re-additization. At lower IP values, the amount of antioxidant required increased significantly, and the effectiveness tended to be reduced. Once IP fell to essentially zero, the acid content increased to above the allowable limit. Insoluble material was detectable after the acid number increased out of specification. Storage life was increased with re-additization relative to the as-received fuels, as evidenced by longer time to produce acids. Experience in the field may vary based on storage conditions; however, these results indicate re-additization can significantly increase the storage life of biodiesel blends when used with regular monitoring of IP and acid number. An assessment of property changes during long-term storage showed the initial IP did not predict storage behavior, although fuels above the specification minimum remained stable for greater than 12 weeks of D4625 accelerated aging (1 one year simulated).

09 BIOMASS FUELS↗
DOE OSTI2020

Investigation of structural effects of aromatic compounds on sooting tendency with mechanistic insight into ethylphenol isomers

Small aromatic molecules with oxygen-containing functional groups are a promising class of fuel additives, as they can be readily sourced from depolymerized lignin. These oxygenated aromatic compounds (OACs) show a lower sooting tendency than aromatic hydrocarbons, but OACs having alkyl groups such as ethylphenol show a higher sooting tendency than other OACs such as phenol and anisole, despite the oxygen moiety. In this study, we investigate the relationship between chemical structure and soot precursor formation to explain observed differences in the sooting tendency of OACs and to gain insight into how alkyl or oxygenated substituents on the aromatic ring affect soot precursor formation. The weakest bond for 15 aromatic compounds was identified and cleavage of these bonds was shown to generate either benzyl or phenoxy radicals. A linear relationship between standard enthalpy of formation (ΔH f o ) of these radicals and the yield sooting index (YSI) was found, and thus ΔH f ° can be applied as a metric to estimate YSIs of various aromatic compounds; higher ΔH f o of a radical indicates an increase in the radical reactivity and leads to more soot precursor formation. Flow reactor experiments were performed for 2-ethylphenol and 3-ethylphenol to elucidate how ortho and meta substitution effects the sooting tendency. Soot precursors were identified from the experiment and their formation pathways were investigated computationally. 2-ethylphenol produces more oxygenated products than 3-ethylphenol since the ortho position has increased resonance stabilization of radical intermediates, which leads to lower YSI. Overall, these results further inform the selection of potential biomass-derived fuel blendstocks that have favorable sooting tendencies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

What fuel properties enable higher thermal efficiency in spark-ignited engines?

The Co-Optimization of Fuels and Engines (Co-Optima) initiative from the US Department of Energy aims to co-develop fuels and engines in an effort to maximize energy efficiency and the utilization of renewable fuels. Many of these renewable fuel options have fuel chemistries that are different from those of petroleum-derived fuels. Because practical market fuels need to meet specific fuel-property requirements, a chemistry-agnostic approach to assessing the potential benefits of candidate fuels was developed using the Central Fuel Property Hypothesis (CFPH). The CFPH states that fuel properties are predictive of the performance of the fuel, regardless of the fuel's chemical composition. In order to use this hypothesis to assess the potential of fuel candidates to increase efficiency in spark-ignition (SI) engines, the individual contributions towards efficiency potential in an optimized engine must be quantified in a way that allows the individual fuel properties to be traded off for one another. This review article begins by providing an overview of the historical linkages between fuel properties and engine efficiency, including the two dominant pathways currently being used by vehicle manufacturers to reduce fuel consumption. Then, a thermodynamic-based assessment to quantify how six individual fuel properties can affect efficiency in SI engines is performed: research octane number, octane sensitivity, latent heat of vaporization, laminar flame speed, particulate matter index, and catalyst light-off temperature. The relative effects of each of these fuel properties is combined into a unified merit function that is capable of assessing the fuel property-based efficiency potential of fuels with conventional and unconventional compositions.

42 ENGINEERING↗
DOE OSTI2020

Elucidating the Chemical Pathways Responsible for the Sooting Tendency of 1 and 2-phenylethanol

Yield Sooting Index (YSI) measurements have shown that oxygenated aromatic compounds (OACs) tend to have lower YSI than aromatic hydrocarbon (AHC) compounds. For example, typical AHCs such as toluene and ethyl benzene have a YSI of 170 and 216, respectively, in contrast, OACs such as phenol and anisole have a YSI of 81 and 111, respectively. However, this trend is not always true as was observed for the structural isomers 1-phenylethanol (1PE, YSI=142) and 2-phenylethanol (2PE, YSI=207), where 2PE contains a YSI more representative of AHCs than OACs. We applied flow reactor experiments and density functional theory (DFT) calculations to examine how oxygen functionality present in 1PE and 2PE alters the reaction pathways leading to the observed difference in soot formation. It was determined that the proximity of the oxygen functional group to the aromatic ring determines whether the oxygen remains attached to the primary reacting species (for 1PE) or is eliminated early in the combustion sequence (for 2PE). For these alcohols, preservation of the oxygen in the molecule leads to further OACs, while loss of the oxygen leads to AHCs and benzyl radical. The direct pathways to AHCs and benzyl radical result in the higher YSI observed for 2PE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗