Search NASA⌕ Search

Engineering topics

McDaniel, Anthony H.

Publications and source records attributed to McDaniel, Anthony H..

At least 19 records

Solar Thermochemical Redox Cycling Using Ga- and Al-Doped LSM Perovskites for Renewable Hydrogen Production

Solar thermochemical hydrogen production using redox-active metal oxides is a promising pathway for the production of green hydrogen and synthetic fuel precursors. Herein, the perovskite material (La 0.6 Sr 0.4 ) 0.95 Mn 0.8 Ga 0.2 O 3–δ (LSMG6482) is identified as a promising metal oxide for thermochemical water splitting. LSMG6482, along with more-established water splitters ceria and (La 0.6 Sr 0.4 ) 0.95 Mn x Al 1–x O 3–δ (LSMA) perovskites, is experimentally characterized via thermogravimetric (TGA) analysis and high-temperature water splitting in a reactor simulating solar concentrating conditions. TGA analysis demonstrated that LSMG6482 has high and stable oxygen exchange capacity under controlled pO 2 redox cycling, demonstrated by large changes in oxygen nonstoichiometry (δ) relative to ceria. Water splitting experiments using laser heating (T red = 1400 °C, T ox = 1200 °C) resulted in H 2 yields of 165.1 μmol g –1 for the candidate LSMG6482 composition, exceeding that of all benchmark materials tested. Under high conversion oxidation conditions, where H 2 is cointroduced with H 2 O (150 ≤ nH 2 O/nH 2 ≤ 500), H 2 yields were greatest for LSMG6482 and LSMA6482, up to four times that of ceria at the highest nH 2 O/nH 2 conditions. Crystallographic analysis showed that over the course of experimentation, there is some secondary phase growth for all perovskite compositions, except for LSMA6482, but there was no observable degradation in H 2 yields.

08 HYDROGEN↗

Stabilization of Catalytically Active Surface Defects on Ga-doped La–Sr–Mn Perovskites for Improved Solar Thermochemical Generation of Hydrogen

Solar thermochemical hydrogen (STCH) production from water splitting typically requires performing redox cycles at temperatures above 1200 °C to reduce and re-oxidize the bulk of a reversible material. Bulk processes such as oxygen vacancy formation and oxygen diffusion energies dictate the viability of a material for STCH. The surface plays an important role in the formation and destruction of vacancies and interacts with gas phase water and surface adsorbed species. These surface processes can lead to surface reconfigurations and even the formation of surface phases with stoichiometry and oxygen content very different from the bulk composition. Understanding in-situ the surface chemical state and its evolution under water splitting is important to design nonstoichiometric oxides capable of longer-lasting STCH generation at lower temperatures. In this work, we describe the water splitting active defect sites in LSM ((La 0.65 Sr 0.35 ) 0.95 MnO 3–δ ) and Ga-doped LSM ((La 0.6 Sr 0.4 ) 0.95 (Mn 0.8 Ga 0.2 )O 3–δ ) perovskites during Operando thermochemical water splitting conditions using ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) experiments at 800 °C under steam. We show that sub-stoichiometric La +3 in the oxygen-vacancy rich surface at operating conditions can be used to correlate surface water splitting activity and the creation of surface hydroxide intermediates. The addition of Ga in LSM is shown to drastically stabilize the surface chemical composition by preventing Sr segregation and stabilizing catalytically active surface defects that promote the binding of adsorbed hydroxides. Here, we use Operando AP-XPS quantification of metastable surface hydroxide intermediates (La(OH) 3 ) to determine the amount of catalytically active surface sites in LSM (2.9%) and in LSMG (7.8–8.1%, depending on the bulk oxidation state).

08 HYDROGEN↗

Manganese-based A-site high-entropy perovskite oxide for solar thermochemical hydrogen production

Non-stoichiometric perovskite oxides have been studied as a new family of redox oxides for solar thermochemical hydrogen (STCH) production owing to their favourable thermodynamic properties. However, conventional perovskite oxides suffer from limited phase stability and kinetic properties, and poor cyclability. Here, we report a strategy of introducing A-site multi-principal-component mixing to develop a high-entropy perovskite oxide, (La 1/6 Pr 1/6 Nd 1/6 Gd 1/6 Sr 1/6 Ba 1/6 )MnO 3 (LPNGSB_Mn), which shows desirable thermodynamic and kinetics properties as well as excellent phase stability and cycling durability. LPNGSB_Mn exhibits enhanced hydrogen production (~77.5 mmol mol oxide -1 ) compared to (La 2/3 Sr 1/3 )MnO 3 (~53.5 mmol mol oxide -1 ) in a short 1 hour redox duration and high STCH and phase stability for 50 cycles. LPNGSB_Mn possesses a moderate enthalpy of reduction (252.51–296.32 kJ (mol O) -1 ), a high entropy of reduction (126.95–168.85 J (mol O) -1 K -1 ), and fast surface oxygen exchange kinetics. All A-site cations do not show observable valence changes during the reduction and oxidation processes. In conclusion, this research preliminarily explores the use of one A-site high-entropy perovskite oxide for STCH.

08 HYDROGEN↗

Assessment of Bulk Oxygen Capacity and Transient Redox Behavior of Foamed Lanthanum Strontium Manganese Perovskites

Synthesis of solar thermochemical hydrogen (STCH) production redox materials with engineered structures, for example, replica foams, can enable efficient heat and mass transport and are critical for scaled-up systems. Prior work has motivated the use of lanthanum strontium manganese (LSM)-type perovskites as foamed STCH materials, but the effect of their morphology on bulk and kinetic behavior has not been reported. In this work, replica and direct foamed samples of La 0.65 Sr 0.35 MnO 3-δ (LSM35) were fabricated and compared to synthesized powders and dense monoliths, and similarly synthesized CeO 2-δ (ceria) foams, regarding their specific reaction rates and bulk oxygen capacity/H 2 yields. Changes in oxygen capacity (Δδ) and reaction rates were measured between 1200 °C and 1400 °C by using fixed ratios of steam and hydrogen during both reduction and oxidation steps, allowing for analysis under practical high conversion conditions. Results suggest bulk behavior and reaction rates of the foamed LSM materials are comparable to their powder analogues. Differences in reaction rates were observed only when replica foamed samples were subjected to rapid laser heating (emulating conditions expected in solar furnaces), which is expected but has not been demonstrated at such a small scale. Here, foamed samples were further subjected to 50 redox cycles at 1400 °C to evaluate their stability. Results show no statistically significant decrease in hydrogen production for any of the foamed samples, but the direct foamed samples became brittle with time. Together, these results demonstrate the viability of replica foamed LSM perovskites for integration in scaled-up STCH systems.

08 HYDROGEN↗

Defect graph neural networks for materials discovery in high-temperature clean-energy applications

We present a graph neural network approach that fully automates the prediction of defect formation enthalpies for any crystallographic site from the ideal crystal structure, without the need to create defected atomic structure models as input. Here we used density functional theory reference data for vacancy defects in oxides, to train a defect graph neural network (dGNN) model that replaces the density functional theory supercell relaxations otherwise required for each symmetrically unique crystal site. Interfaced with thermodynamic calculations of reduction entropies and associated free energies, the dGNN model is applied to the screening of oxides in the Materials Project database, connecting the zero-kelvin defect enthalpies to high-temperature process conditions relevant for solar thermochemical hydrogen production and other energy applications. The dGNN approach is applicable to arbitrary structures with an accuracy limited principally by the amount and diversity of the training data, and it is generalizable to other defect types and advanced graph convolution architectures. In conclusion, it will help to tackle future materials discovery problems in clean energy and beyond.

97 MATHEMATICS AND COMPUTING↗

Multiple and nonlocal cation redox in Ca–Ce–Ti–Mn oxide perovskites for solar thermochemical applications

Modeling-driven design of redox-active off-stoichiometric oxides for solar thermochemical H 2 production (STCH) seldom has resulted in empirical demonstration of competitive materials. Here, we report the theoretical prediction and experimental evidence that the perovskite Ca 2/3 Ce 1/3 Ti 1/3 Mn 2/3 O 3 is synthesizable with high phase purity, stable, and has desirable redox thermodynamics for STCH, with a predicted average neutral oxygen vacancy (VO) formation energy, E v = 3.30 eV. Flow reactor experiments suggest potentially comparable or greater H 2 production capacity than recent promising Sr–La–Mn–Al and Ba–Ce–Mn metal oxide perovskites. Utilizing quantum-based modeling of a solid solution on both A and B sub-lattices, we predict the impact of nearest-neighbor composition on E v and determine that A-site Ce 4+ reduction dominates the redox-activity of Ca 2/3 Ce 1/3 Ti 1/3 Mn 2/3 O 3 . X-ray absorption spectroscopy measurements provide evidence that supports these predictions and reversible Ce 4+ -to-Ce 3+ reduction. Our models predict that Ce 4+ reduces even when it is not nearest-neighbor to the V O , suggesting that refinement of Ce stoichiometry has the possibility of further enhancing performance.

08 HYDROGEN↗

Synchrotron-based techniques for characterizing STCH water-splitting materials

Understanding the role of oxygen vacancy–induced atomic and electronic structural changes to complex metal oxides during water-splitting processes is paramount to advancing the field of solar thermochemical hydrogen production (STCH). The formulation and confirmation of a mechanism for these types of chemical reactions necessitate a multifaceted experimental approach, featuring advanced structural characterization methods. Synchrotron X-ray techniques are essential to the rapidly advancing field of STCH in part due to properties such as high brilliance, high coherence, and variable energy that provide sensitivity, resolution, and rapid data acquisition times required for the characterization of complex metal oxides during water-splitting cycles. X-ray diffraction (XRD) is commonly used for determining the structures and phase purity of new materials synthesized by solid-state techniques and monitoring the structural integrity of oxides during water-splitting processes (e.g., oxygen vacancy–induced lattice expansion). X-ray absorption spectroscopy (XAS) is an element-specific technique and is sensitive to local atomic and electronic changes encountered around metal coordination centers during redox. While in operando measurements are desirable, the experimental conditions required for such measurements (high temperatures, controlled oxygen partial pressures, and H 2 O) practically necessitate in situ measurements that do not meet all operating conditions or ex situ measurements. Here, we highlight the application of synchrotron X-ray scattering and spectroscopic techniques using both in situ and ex situ measurements, emphasizing the advantages and limitations of each method as they relate to water-splitting processes. The best practices are discussed for preparing quenched states of reduction and performing synchrotron measurements, which focus on XRD and XAS at soft (e.g., oxygen K-edge, transition metal L-edges, and lanthanide M-edges) and hard (e.g., transition metal K-edges and lanthanide L-edges) X-ray energies. The X-ray absorption spectra of these complex oxides are a convolution of multiple contributions with accurate interpretation being contingent on computational methods. The state-of-the-art methods are discussed that enable peak positions and intensities to be related to material electronic and structural properties. Through careful experimental design, these studies can elucidate complex structure–property relationships as they pertain to nonstoichiometric water splitting. A survey of modern approaches for the evaluation of water-splitting materials at synchrotron sources under various experimental conditions is provided, and available software for data analysis is discussed.

08 HYDROGEN↗

Probing Electronic and Structural Transformations during Thermal Reduction of the Promising Water Splitting Perovskite BaCe 0.25 Mn 0.75 O 3

Here, in this report, we investigate the thermal reduction of the octahedral perovskite BaCe 0.25 Mn 0.75 O 3 (BCM) using in situ electron energy loss spectroscopy (EELS) in an aberration-corrected transmission electron microscope (TEM). The 12R-polytype of BCM is known to demonstrate high solar thermochemical hydrogen production capacity. In situ EELS measurements show that Mn is the active redox cation in BCM, undergoing thermal reduction from Mn 4+ to Mn 3+ during heating to 700 °C inside the TEM under a high vacuum. The progressive reduction of Mn 4+ during oxygen vacancy (O v ) formation was monitored as a function of temperature. Additionally, atomic-resolution scanning transmission electron microscopy identified two different types of twin boundaries present in the oxidized and reduced form of 12R-BCM, respectively. These two types of twin boundaries were shown, via computational modeling, to modulate the site-specific O v formation energies in 12R-BCM. It is concluded that these types of atomic defects provide sites more energetically favorable for O v formation during thermal reduction.

36 MATERIALS SCIENCE↗

Initiating a Roadmap for Solar Fuels R&D: Imagining Beyond Thermochemical Cycles

Sandia National Laboratories in collaboration with the National Renewable Energy Laboratory outline a framework for developing a solar fuels roadmap based on novel concepts for hybridizing gas-splitting thermochemical cycle s with high-temperature electro chemical steps. We call this concept SoHyTEC, a Solar Hybrid Thermochemical-Electrochemical Cycle. The strategy focuses on transforming purely thermochemical cycles that split water (H 2 O) and carbon dioxide (CO 2 ) to produce hydrogen (H 2 ) and carbon monoxide (CO) , respectively, the fundamental chemical building blocks for diverse fuels and chemicals , by substituting thermochemical reactions with high-temperature electrochemical steps. By invoking high-temperature electrochemistry, the energy required to complete the gas-splitting cycle is divided into a thermal component (process temperature) and an electrical component (applied voltage). These components, sourced from solar energy, are independently variable knobs to maximize overall process efficiency. Furthermore, a small applied voltage can reduce cycle process temperature by hundreds of degrees , opening the door to cost-effective solar concentrators and practical receiver/reactor de signs. Using the SoHyTEC concept as a backdrop, we outline a framework that advocates developing methods for automating information gathering, critically evaluating thermochemical cycles for adapting into SoHyTEC, establishing requirements based on thermodynamic analysis, and developing a model-based approach to benchmarking a SoHyTEC system against a baseline concentrating solar thermal integrated electrolysis plant. We feel these framework elements are a necessary precursor to creating a robust and adaptive technology development roadmap for producing solar fuels using SoHyTEC. In one example, we introduce high-temperature electrochemistry as a method to manipulate a fully stoichiometric two-step metal oxide cycle that circumvents costly separation processes and ultra-high cycle temperatures. We also identify and group water-splitting chemistries that are conceptually amenable to hybridization.

14 SOLAR ENERGY↗

The role of H–H interactions and impurities on the structure and energetics of H/Pd(111)

Understanding hydrogen incorporation into palladium requires detailed knowledge of surface and subsurface structure and atomic interactions as surface hydrogen is being embedded. Using density functional theory (DFT), we examine the energies of hydrogen layers of varying coverage adsorbed on Pd(111). Here we find that H–H and H–Pd interactions promote the formation of the well-known ($\sqrt{3}$ x $\sqrt{3}$) phases but also favor an unreported (3 × 3) phase at high H coverages for which we present experimental evidence. We relate the stability of isolated H vacancies of the (3 × 3) phase to the need of H 2 molecules to access bare Pd before they can dissociate. Following higher hydrogen dosage, we observe initial steps of hydride formation, starting with small clusters of subsurface hydrogen. The interaction between H and Pd is complicated by the persistent presence of carbon at the surface. X-ray photoelectron spectroscopy experiments show that trace amounts of carbon, emerging from the Pd bulk despite many surface cleaning cycles, become mobile enough to repopulate the C-depleted surface at temperatures above 200 K. When exposed to hydrogen, these surface carbon atoms react to form benzene, as evidenced by scanning tunneling microscopy observations interpreted with DFT.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Computationally Accelerated Discovery and Experimental Demonstration of Gd0.5La0.5Co0.5Fe0.5O3 for Solar Thermochemical Hydrogen Production

Solar thermochemical hydrogen (STCH) production is a promising method to generate carbon neutral fuels by splitting water utilizing metal oxide materials and concentrated solar energy. The discovery of materials with enhanced water-splitting performance is critical for STCH to play a major role in the emerging renewable energy portfolio. While perovskite materials have been the focus of many recent efforts, materials screening can be time consuming due to the myriad chemical compositions possible. This can be greatly accelerated through computationally screening materials parameters including oxygen vacancy formation energy, phase stability, and electron effective mass. In this work, the perovskite Gd 0.5 La 0.5 Co 0.5 Fe 0.5 O 3 (GLCF), was computationally determined to be a potential water splitter, and its activity was experimentally demonstrated. During water splitting tests with a thermal reduction temperature of 1,350°C, hydrogen yields of 101 μmol/g and 141 μmol/g were obtained at re-oxidation temperatures of 850 and 1,000°C, respectively, with increasing production observed during subsequent cycles. This is a significant improvement from similar compounds studied before (La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 and LaFe 0.75 Co 0.25 O 3 ) that suffer from performance degradation with subsequent cycles. Confirmed with high temperature x-ray diffraction (HT-XRD) patterns under inert and oxidizing atmosphere, the GLCF mainly maintained its phase while some decomposition to Gd 2-x La x O 3 was observed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗