Search NASA⌕ Search

Engineering topics

McDeavitt, Sean M.

Publications and source records attributed to McDeavitt, Sean M..

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Concept Descriptions for the VTR Rabbit System and Driver Fuel Test Assemblies

Two of the experiment vehicles being developed for the Versatile Test Reactor (VTR) are presented here. The first is a rabbit system that will enable rapid insertion of small test capsules into the high fast flux of the VTR core for relatively short durations. The rabbit concept development includes the construction/demonstration of a near-full-scale system in a deep-water pool to demonstrate functionality, development of a concept of operations and initial procedures, and validation of thermal-hydraulic modeling. In addition, modeling efforts are underway to simulate the thermal and neutronic environment of a rabbit capsule. The second type of experiment vehicle presented here is a driver fuel test assembly for inserting fuel and materials tests into the core by replacing a driver fuel assembly. Here, a novel design for dismountable test assemblies is proposed for the VTR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

A sensitivity analysis to predict the neutronics behavior of samples irradiated in the VTR rabbit system

We report a low-order neutronics model is developed to carry out hundreds of simulations efficiently and investigate the neutronics behavior of samples being irradiated in a test reactor setting under different geometrical constraints. The low-order model allowed for simulations that yield the expected neutronics behavior of any irradiated sample in any environment and allows for the calculation of highly accurate spatially averaged statistics and idealized spatial distributions in the neutron flux. Several benchmarks are performed to evaluate the performance and limitations of the low-order model revealing many important findings. The low-order model predicted the LHGR in the EBR-II driver fuel to within 2.34% by only simulating the fuel rod by itself, which served as a validation for the model. Sensitivity studies investigated 3% enriched UO 2 and U-10Zr being irradiated in the Versatile Test Reactor rabbit system. The analyses investigated a range of combinations of 15 radii and 5 heights for each sample in the rabbit system. Similar data sets are also provided for irradiations in the Advanced Test Reactor’s B-10 irradiation position, which is a thermal neutron spectrum environment. Generalized fits and fit coefficients are obtained for sample heating, reaction rate densities, and local multiplication rate characteristics, allowing the predictions of the neutronics behavior of the samples based on their geometrical constraints. The analyses and fits laid the groundwork for developing a user-end Multiphysics analysis framework to assist and accelerate irradiation experiment design and optimization.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Thermal-shock experiments for separate-effects validation of UO 2 fuel fracture models

Because of the important role that fracture plays in the behavior of ceramic UO2 fuel in a nuclear reactor environment, fracture models are a major component of fuel performance codes. As with any aspect of fuel performance, it is crucial to validate these fracture models against experimental data; however, obtaining well-controlled data for conditions representative of a reactor environment is difficult. Quenching is proposed here as a relatively simple approach for using a laboratory environment to achieve conditions that approximate those of a reactor environment. In this paper, an experimental apparatus containing a single instrumented fuel pellet in a sealed section of copper tubing is developed. It is then applied to a series of seven experiments in which the apparatus is first heated to a high temperature (580-680°C) by immersion in a molten salt bath, then quenched in a cold bath (-10-4 °C). Development of these experiments was guided by numerical simulations, and post-test simulations were performed to aid in understanding the experimental behavior and assessing the accuracy of the predictions of fracture initiation and propagation. In addition, similar experiments were performed on solid copper rods to provide temperature-dependent heat transfer coefficients for use in simulations of these experiments. Here, this study demonstrates that quenching is a viable approach for generating thermal gradients representative of those in prototypical light-water reactor conditions at powers of about 5–10 kW/m. Fracture is expected to begin at these power levels, and moderate amounts of radial and axial cracking was observed in these quenching tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Experimentally validated multiphysics modeling of fracture induced by thermal shocks in sintered UO 2 pellets

Uranium Dioxide (UO 2 ) fuel powers almost all commercial Nuclear Power Plants (NPPs) worldwide, generating carbon-free energy and contributing to the fight against climate change. UO 2 fuel incurs damage and fractures due to large thermal gradients that develop across the fuel pellet during normal and transient operating conditions. A comprehensive understanding of the underlying mechanisms by which these processes take place is still lacking. A combined experimental and computational approach is utilized here to quantify the behavior of UO 2 fuel fracture induced by thermal shock. Here, this work introduces both (1) an experimental study to understand the fuel fracturing behavior of sintered UO 2 pellets when exposed to thermal shock, and (2) a Multiphysics phase-field fracture model capable of simulating this process. Parametric studies were conducted to evaluate the effects of uncertainties in fracture properties on the fracture behavior of UO 2 due to thermal shocking. A set of energy release rate (or equivalently fracture toughness) and contract area (the part of the fuel pellet in direct contact with the cold bath) were able to capture the overall fracture trends of the corresponding experimental data. Our combined approach presents a new method for accounting for the effects of microstructure and sample size on the energy release rate/fracture toughness. The experimental data were collected from multiple experiments that exposed UO 2 pellets to high-temperature conditions (589–676 °C) followed by a quench in sub-zero water. This work demonstrates that joint experimental and computational efforts are able to advance the understanding of thermal fracture in the primary fuel source for existing and future NPPs.

36 MATERIALS SCIENCE↗