Engineering topics

McDuffee, Joel L.

Publications and source records attributed to McDuffee, Joel L..

5 records

DOE OSTI2024

Critical response to M. Worrall et al. Published in Annals of Nuclear Energy 207 (2024) 110731

M. Worrall et al. recently published a manuscript titled “Fast neutron irradiation capability in existing thermal test reactors” (Worrall, 2024) that summarizes an irradiation vehicle design that would boost the fast neutron flux in the Advanced Test Reactor (ATR) for testing of nonfuel materials in a neutron flux energy spectrum that is more representative of fast reactors. Here, the authors compare their design with a separate vehicle design that they conceived of that would be implemented within the High Flux Isotope Reactor (HFIR). They analyzed both designs and drew conclusions on the most realistic near-term options for shielded nonfuel material irradiations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2024

Heat transfer optimization of uo 2 -mo fuel using genetic algorithms

Two genetic algorithm (GA) methods were applied to thermal finite element models to optimize the heat transfer efficacy of a UO 2 -Mo composite fuel pellet with typical pressurized water reactor fuel geometry. Mo additions to UO 2 have been shown to increase the thermal conductivity, thus reducing centerline temperatures and temperature gradients. Previous studies evaluated uniformly dispersed Mo or continuous Mo internal geometries (e.g., fins, plates, discs) that were selected using engineering intuition. The current study uses two different implementations of the same GA to optimize Mo placement and minimize the fuel temperature with the only constraint being a maximum 10% Mo volume fraction. One approach superimposed Mo line elements onto the monolithic UO 2 pellet model, and the other converted entire UO 2 volume elements to Mo. The former method generated 1D heat transfer connections between nodes, whereas the latter method allowed for the formation of 3D structures. Features of the optimal fuel design produced by the GAs included dispersed Mo near the centerline that shifted the peak fuel temperature outward by 0.6 mm, Mo chains in the high-heat-flux region in the mid-to-outer radial zone, and a large continuous structure that spanned the full radius and height of the pellet and accounted for 87.7 % of the total Mo in the pellet. Analysis of this design indicates that the optimal Mo configuration is a balance between creating continuous heat transfer pathways and optimally dispersing Mo to minimize the heat transfer distance through UO 2 . This architecture ultimately produced an effective thermal conductivity of 11.3 W/m·K under the assumed boundary conditions. This result is higher than any previous values from the literature. In conclusion, potential fabrication methods and challenges are discussed in addition to the implications on fuel performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Testing and Simulation of an Updated Cartridge Loop Vehicle

The Versatile Test Reactor (VTR) is a sodium-cooled, fast-spectrum test reactor that is being developed in the United States and will support a variety of irradiation test vehicle configurations, including cartridge loops. This work includes out-of-pile experimental results from a single-phase, natural circulation cartridge loop vehicle with geometry relevant to VTR irradiation sites, as well as comparisons between the experimental results and results predicted using the TRAC/RELAP Advanced Computational Engine (TRACE) modeling tool. The experiments were conducted in the thermosyphon test loop (TSTL) facility at Oak Ridge National Laboratory. Comparisons are also made between the current experimental data and results from natural circulation experiments previously conducted in the TSTL in a cartridge vehicle that is similar in design but has smaller flow areas. This cartridge vehicle and the experimental program were developed to add to the single-phase, natural circulation data collected in the previous iteration of the cartridge loop design, which supports future irradiation experiments and adds to a database that is useful for validating computer models. Comparisons of experimental results to TRACE model predictions is a pertinent step in validating the computational tool for supporting future irradiation experiment design and safety calculations, and comparisons to previous cartridge loop results highlight the impact of the design changes made to the test vehicle. The experiments conducted include several steady state tests and transients, including power ramp, loss of offsite power, and loss of external flow scenarios. This work shows that TRACE can accurately predict temperatures and flow conditions in the cartridge loop and the updated vehicle design achieves higher mass flow rates at the same steady state power levels.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2022

Neutron irradiation of tungsten in hydrogen environment at HFIR

Neutron irradiation of tungsten with and without the presence of hydrogen is needed to understand the influence of hydrogen on microstructure development under fusion reactor conditions. However, there is a risk of ignition if air ingress occurs during seal welding of irradiation capsules in a pressurized hydrogen environment. Therefore, an irradiation capsule was designed that contains several disks of vanadium hydrides at a 30% hydrogen-to-metal atomic ratio. During irradiation, the hydrogen is released from the hydrides as the capsule temperature increases, so the irradiation capsule environment is mostly hydrogen when the capsule reaches its 400 °C design temperature. In this study, we describe the design and operating characteristics of this first-of-a-kind irradiation capsule.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Single-phase, natural circulation annular flow measurements for cartridge loop irradiation experiments

The nuclear industry is increasingly considering cartridge-style experiments for irradiation testing of advanced reactor fuels and materials under flowing conditions. Cartridge loops do not require the extensive support infrastructure that are necessary for external flow loops and minimize the possibility of coolant solidification over the long distance from the reactor to the external facilities. However, there is a general lack of quality flow data for internally heated fluids in an annular configuration representative of a cartridge-type irradiation experiment, particularly one with natural circulation. To address this data need, a series of experiments was conducted to measure the natural circulation flow rates of pressurized water in a sealed, internally heated vessel with annular flow conditions that represent a molten salt or sodium cartridge loop. Temperatures and flow rates were measured under steady-state and transient conditions. Here, this paper describes the facility, methods, and results of the experiments, including the determination of nondimensional parameters. A simple 1D model of the natural convection flow rates agrees well with the experimental results. Applying this model to simulate a liquid salt cartridge experiment predicts that natural circulation flow might be able to provide liquid salt Reynolds numbers similar to those of some molten salt reactor concepts at relevant power densities.

42 ENGINEERING↗