Search NASA⌕ Search

Engineering topics

McFarlane, Joanna

Publications and source records attributed to McFarlane, Joanna.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

NO 2 -mediated voloxidation for iodine separation from cesium iodide surrogates

Heterogeneous NO 2 -mediated oxidation of uranium, also known as advanced voloxidation, is a proposed head-end reprocessing method for used nuclear fuel. An advantage of advanced voloxidation is the removal of volatile fission products, which complicate downstream separation and containment challenges leading to increased processing economics. Iodine, one of the volatile species of interest, has exhibited varied results in this process. Using CsI as a surrogate material, this work mimics the effect of NO 2 -based voloxidation on iodine and sheds light on the factors that influence the solid–gas phase reaction. Solid-state analysis using Fourier transform infrared attenuated total reflectance spectroscopy and scanning electron microscopy with energy-dispersive X-ray spectroscopy confirmed the conversion of CsI to CsNO 3 . Iodine separation ranged from 46% to 100% across multiple tests. Iodine separation was most effective when multiple recharges of NO 2 were administered. In conclusion, at the bench scale, liberating iodine from CsI appears to occur within 1 h, but the presence of surface H 2 O and the composition of the NO x reagent mixtures greatly influence its success.

advanced voloxidation↗
DOE OSTI2024

The chlorination and separation of aluminum using low-temperature sulfur chloride reagents

There is currently no strategy for the permanent waste disposal or recycling for used nuclear fuelsfrom research reactors. For this reason, low-temperature reactions have been developed for thechlorination of the Al alloys and subsequent separation from used nuclear fuels to reducethe volume of high-level waste in storage. Three sulfur chloride reagents – S 2 Cl 2 , SOCl 2 , and SO 2 Cl 2 —were tested, and two were found to quantitatively chlorinate Al metal and Al alloys undermild conditions. Further, these low-temperature reactions proceed between 298 and 411 K, and up to 5 gof metal is chlorinated in 1–3 h. Preliminary results indicate that the reactivity and exothermicity ofthe reaction between the Al and sulfur chloride reagents is highly dependent on the surface area-to-volume ratio of the metal and the volume of solvent. Elemental S is produced as a by-productduring the chlorination with S 2 Cl 2 but can be quantitatively rechlorinated under mild conditions toregenerate the initial chlorination reagent. Therefore, in this case, chlorine is the only elementconsumed in the reaction, thus minimizing the waste generated during the chlorination process.The AlCl 3 may then be separated from other materials present in Al 6061 or Al 8001 because of itshigh solubility in the sulfur chloride reagents. This process may also be extended to chlorinate Alfrom research reactor fuels.

aluminum↗
DOE OSTI2024

Iodine solid sorbent design: a literature review of the critical criteria for consideration

Designing sorbents for iodine capture in different conditions requires selection and optimization of a large and diverse range of variables. These variables fall into general categories (or features) of sorbent activity, sorbent stability, and the fate of the loaded material in terms of the disposal (waste form) options available. To illustrate, silver-loaded, high-porosity sorbents make for maximized iodine capture and less pressure drop in a column-based sorption system approach, however, this high porosity can lead to less mechanically stable sorbents. Additionally, waste forms containing silver must also be compliant with additional criteria for hazardous waste disposal. Thus, all these aspects must be considered simultaneously when selecting a sorbent for utilization under specific conditions. Information is given for different types of sorbent design considerations for different operating conditions and some emphasis is also given on promising alternatives for silver as the active (chemisorption-based) getter metal. Discussion is given around demonstrated options for waste forms for different metal-iodide compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Aerosol and Gas Transport in Ventilation Ducts in Nonreactor Nuclear Facilities

This document summarizes outcomes and finding in FY 2022 from a project sponsored by the Nuclear Safety Research and Development Program, which is managed by the Office of Nuclear Safety, within the Office of Environment, Health, Safety and Security. Literature survey and data collection are discussed in Sections 1 and 2, respectively. Numerical modeling of particulate transports in ventilation systems performed for standard geometries and a full-scale ventilation system is described in Section 3, and Section 4 summarizes the development of proof-of-concept sensors featuring ultrasound technology for particle deposition removal. Conclusions and recommendations are outlined in Section 5.

42 ENGINEERING↗
DOE OSTI2024

Analytical capabilities for iodine detection: Review of possibilities for different applications

This Review summarizes a range of analytical techniques that can be used to detect, quantify, and/or distinguish between isotopes of iodine (e.g., long-lived 129 I, short-lived 131 I, stable 127 I). One reason this is of interest is that understanding potential radioiodine release from nuclear processes is crucial to prevent environmental contamination and to protect human health as it can incorporate into the thyroid leading to cancer. It is also of interest for evaluating iodine retention performances of next-generation iodine off-gas capture materials and long-term waste forms for immobilizing radioiodine for disposal in geologic repositories. Depending upon the form of iodine (e.g., molecules, elemental, and ionic) and the matter state (i.e., solid, liquid, and gaseous), the available options can vary. In addition, several other key parameters vary between the methods discussed herein, including the destructive vs nondestructive nature of the measurement process (including in situ vs ex situ measurement options), the analytical data collection times, and the amount of sample required for analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Density Measurements of Molten LiF–BeF 2 and LiF–BeF 2 –LaF 3 Salt Mixtures by Neutron Radiography

The densities of eutectic (LiF) 2 –BeF 2 and mixtures of this salt (FLiBe) with LaF 3 were measured by dilatometry and by neutron attenuation from 673 K to 1,073 K. Because LaF 3 has a limited solubility in FLiBe, it was necessary to determine the amount of LaF 3 in solution before the density could be determined. The FLiBe density determination was favorably benchmarked against the literature data. A simple comparison was not available for the LaF 3 –FLiBe mixtures, so extrapolation of published data was necessary based on analysis using the Molten Salt Thermal Properties Database-Thermochemistry, or MSTDB-TC, developed by the US Department of Energy. Solubilities for LaF 3 in FLiBe ranged from 1 to 4 mol % over 673 to 1,073 K. The salt system was heated and cooled over 24 h to evaluate potential changes in composition and hysteresis during the measurement. Changes in the meniscus were observed, and these were included in the correction for density determinations. Salt surface tension may have led to supersaturation of LaF 3 in the salt because the solubility curve was nonlinear with respect to the inverse temperature, as would be expected for an ideal system. Surface tension measurements are currently underway to test this hypothesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Semi-empirical model for Henry’s law constant of noble gases in molten salts

Henry’s law constant, which describes the proportionality of dissolved gas to partial pressure of free gas in liquid–gas equilibrium systems, can also be applied to mass transport applications. In this work, we investigated an approach for determining the solubility of noble gases in a molten salt liquid utilizing the equilibrium concept of Henry’s gas constant. Henry’s gas constant is described as a mathematical function dependent on the van der Waals radius of the noble gas and the temperature of the molten salt. The alteration in Gibbs free energy encompasses contributions from both surface and volume energies. Enthalpy and entropy are deduced from these surface and volume energies in the Gibbs free energy formulation. A comparative analysis was conducted between the conventional method and our proposed model. Moreover, useful chemical properties can be determined from examination of surface and volume energies. Our findings provide an accurate and general theory of Gibbs free energy that can be validated experimentally based on the model proposed herein. This work unifies the prediction of Henry gas constant and subsequently the entropy and enthalpy calculation for noble gases in a molten salt solution to a single functional form using van der Waals radius of the gas and temperature of the system. This functional form is then used to perform a multiple regression method to find two parameters corresponding to the surface energy and volume energy. These two parameters are consistent between all combinations of noble gas and molten salt.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Cradle to grave: the importance of the fuel cycle to molten salt reactor sustainability

Advanced reactor technologies are being considered for the next-generation of nuclear power plants. These plants are designed to have a smaller footprint, run more efficiently at higher temperatures, have the flexibility to meet specific power or heating needs, and have lower construction costs. This paper offers a perspective on molten salt reactors, promoted as having a flexible fuel cycle and close-to-ambient pressure operation. A complexity introduced by reducing the reactor footprint is that it may require low-enriched fuel for efficient operation, available from enrichment of the feed salt or by reusing actinides from existing used nuclear fuel (UNF). Recycling UNF has the potential to reduce high-level waste, if done correctly. Release limits from UNF processing are stringent, and processes for waste reduction, fission gas trapping, and stable waste-form generation are not yet ready for commercial deployment. These complex processes are expensive to develop and troubleshoot because the feed is highly radioactive. Thus, fuel production and supply chain development must keep abreast of reactor technology development. Another aspect of reactor sustainability is the non-fuel waste streams that will be generated during operation and decommissioning. Some molten salt reactor designs are projected to have much shorter operational lifetimes than light-water reactors: less than a decade. A goal of the reactor sustainability effort is to divert these materials from a high-level waste repository. However, processing of reactor components should only be undertaken if it reduces waste. Economic and environmental aspects of sustainability are also important, but are not included in this perspective.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Novel Calibration Approach for Monitoring Aerosol Hydrogen Isotopes Using Laser-Induced Breakdown Spectroscopy for Molten Salt Reactor Off-Gas Streams

Online monitoring is a key challenge for the continued development of molten salt reactor (MSR) technology. Laser-induced breakdown spectroscopy (LIBS) has previously been demonstrated to be a viable tool for monitoring aerosolized species and noble gases in real time, but the ability to discern varying isotopes in these streams has not yet been investigated for MSR applications. Tritium will form in MSRs from ternary fission and from (n,α)-reactions occurring in lithium-containing salts. This study compares three spectrometers of varying resolutions and types for measuring hydrogen isotope shifts in LIBS spectra of wetted filter paper. For each spectrometer, multivariate models were built (i.e., principal component regression, partial least squares regression, and multivariate curve resolution) to quantify the isotope ratio. The top models were then modified and corrected to apply the models to aerosol samples with varying isotope ratios. This novel calibration strategy offers an 82% reduction in volume of the calibration samples needed and is a more viable pathway for calibrating deployable LIBS systems. Lastly, this calibration model was compared with an all-aerosol trained model for monitoring hydrogen isotopes during a real-time test where the protium/deuterium ratio, along with representative salt species (i.e., lithium, sodium, and potassium) were adjusted dynamically. Results of this test validated the predictive capabilities of the transferred model and highlighted the capabilities of LIBS for real-time monitoring of MSR effluent streams.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Behavior of contaminants and simulant fission products in the advanced chlorination process

The University of Tennessee, Knoxville and Oak Ridge National Laboratory have completed proof-of principle testing on an advanced sulfur-based zirconium and aluminum chlorination process for the recovery of Zr or Al from spent fuel claddings and purification of the products. This process could be used to recover hafnium-free nuclear-grade zirconium for reuse or disposal as low-level waste. Testing showed that even non-optimized reaction protocols could produce zirconium product streams from simulated irradiated fuel with purities >90%. The chlorination process was tested on representative fission product species that would be found in Advanced Test Reactor fuel (ATR). First, fission product generation was determined through modeling and simulation of the ATR. The generation of fission products was used to selected contaminants and potentially volatile fission product simulants for laboratory testing. The goal is to identify which species may react with the sulfur-chlorine reagents and be transported into the advanced chlorination off-gas.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

High-gradient magnetic separation of colloidal uranium oxide particles from soil components in aqueous suspensions

The separation of uranium oxide (UO 2 ) particles from soil-surrogate particles in aqueous suspensions was achieved using filtration enhanced by a magnetic field. Enhanced attraction of paramagnetic UO 2 colloids to a ferromagnetic stainless-steel filter placed in a strong magnetic field arises because of the positive magnetic susceptibility of the particles and the high-gradient field generated near ferromagnetic fibers. Enhanced uptake of smaller particles over larger ones occurs through Brownian motion that promotes the collision of particles with the ferromagnetic fibers of the filter. Hence, this work focused on UO 2 particles in the colloidal size range. Experiments used a water-cooled electromagnet and an array of permanent magnets. Chemical analysis showed that the magnetic field increased the capture efficiency of uranium particles from a range of 27–53% with the magnet off up to 98% with the magnet on after a single pass of the suspension through the filter. Further, the recovery of the UO 2 particles from the filter, however, was more difficult to achieve. Small amounts of UO 2 , together with significant amounts of background SiO 2 particles, were removed from the filter during a first flush with the magnetic field on. A much larger recovery of UO 2 was not observed until a second out-of-field flush was performed, which also released some SiO 2 . The degree to which particle separation was enhanced through the use of multi-stage filtration compared to single pass-through filtration was also examined. A design was suggested that could be used to optimize the separation efficiency for a continuous process.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Technology Development Roadmap for Volatile Radionuclide Capture and Immobilization

An “Off-Gas and Waste Forms Strategy Workshop” was held in Washington, D.C. on January 31, and February 1, 2023, to review the current state of the art (baseline) technologies for capturing and immobilizing these volatile radionuclides in waste forms (WFs). The discussions in that workshop were used to develop a roadmap for future research and development to mature technologies that are presently not ready for use in a commercial reprocessing facility and develop and demonstrate technologies that provide more safety, more simplicity, or lower costs compared to the current baseline.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Establishing Isotopic Measurement Capabilities using Laser-Induced Breakdown Spectroscopy for the Molten Salt Reactor Campaign

Proof-of-principle H isotope ratios of aqueous aerosol systems and liquid droplets on filter paper have been measured using laser-induced breakdown spectroscopy (LIBS) with root mean square error of prediction values down to 1.9%. Molten salt reactors (MSRs) will consist of a complex chemical and radiological system consistently producing new fission products as the reactor operates. Some of these fission products and/or their daughter species will leave the salt in the reactor off-gas. Monitoring the composition of the off-gas, as well as the salt itself, is important for monitoring reactor performance, including burnup, corrosion, and the concentration of impurities. Tritium is of concern for MSRs because it will be produced from the irradiation of key salt constituents, including Li and Be. LIBS offers an avenue for in situ salt and off-gas monitoring by firing a laser onto or into the sample stream to generate a plasma. The plasma light can be monitored to measure an elemental fingerprint of the sample. Extending this analysis to include isotopic ratios offers a critical expansion of the in situ monitoring capabilities being developed. This study demonstrates the expansion of Oak Ridge National Laboratory’s LIBS capabilities to monitor isotopes and shows how simple calibrations may provide rapid semiquantitative models.

07 ISOTOPE AND RADIATION SOURCES↗