The effect of divertor closure on the impurity stagnation point in detached L-mode discharges on DIII-D
Not Available
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Engineering topics
McLean, A. G.
Publications and source records attributed to McLean, A. G..
SOLPS-ITER modeling of divertor detachment in MAST-U’s super-X double null configuration and comparison to experiment
Not Available
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Simulations of divertor designs that spatially separate power and particle exhaust using mid-leg divertor particle pumping
Predictive design modeling of a Dissipation-Focused Divertor for future operation in DIII-D reveals that increasing the poloidal distance of the pump duct entrance from the target surface along the low-field side divertor baffle increases neutral compression and modifies the spatial distribution of power dissipation. With a divertor pump located mid-leg between the target and the X-point, SOLPS-ITER boundary plasma simulations without drifts predict the formation of a dense neutral cloud near the target with > 30x higher neutral compression in detachment, a more stable detachment front located further from the target, and ~25% lower outer midplane separatrix density required for detachment onset, compared to a pump located in the scrape-off layer at the target surface. Up to 19 MW of power flowing into the divertors is modeled using the following two numerical implementations for particle pumping: a specified fraction of particles incident on variable wall sections of the plasma grid is removed from the computational domain (so-called albedo pumping), and a pump duct is modeled which includes dynamics of kinetic neutrals in the duct. The simulations show that the detachment front is located between the divertor target and the X-point and is relatively stable near the pump entrance, without a strong dependence on gas puff rate or injected power. The mid-leg pump design spatially separates the two primary functions of a divertor (power handling and particle exhaust), with the majority of power dissipation occurring near the target plate and particle exhaust taking place further upstream. The benefit of enhanced dissipation using mid-leg pumping comes at the cost of a higher outer midplane separatrix density for a given amount of particle injection.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
2D analysis of tokamak divertor-plasma detachment-bifurcation with operational parameters and geometries
UEDGE simulations with density scans for various input power, transport coefficients and outer poloidal leg length are performed to study the conditions for the existence of a bifurcation-like drop of T e at the outer strike point, commonly referred to as a detachment cliff, when transitioning to a detached plasma from an attached plasma in the outer divertor as the upstream density increases (McLean et al., 2015). The simulation results show that a detachment cliff tends to occur with a higher power input regardless of diffusivities and leg length. Further analysis of change of plasma profiles at a cliff indicate that, in addition to the sharp reduction of the E x B drift fluxes in the outer divertor studied in Jaervinen et al., (2018), the substantial change of the Mach number in the outer divertor and the decrease of the outer mid-plane T e due to the radiation front moving across the separatrix into the confinement region above the X-point consistently occur for all UEDGE density scans that have a detachment cliff. UEDGE time-dependent simulation of the evolution of a detachment cliff shows that the rapid increase of radiation above the X-point occurs in a time scale of ~0.3–0.5, which could possibly be the trigger for the formation of a detachment cliff, quicker than the Mach number change in a time scale of ~1 ms and the drop of T e in a time scale of ~2–3 ms in the outer divertor.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
First high-power helicon results from DIII-D
Abstract More than 0.6 MW of rf power at 476 MHz has been coupled to DIII-D plasmas by launching helicon (whistler) waves with a traveling-wave antenna (comb-line) in the fast-wave polarization (Van Compernolle et al 2021 Nucl. Fusion 61 116034) which resulted in the observation of electron heating of the core plasma with single-pass absorption based on ray-tracing in L-mode discharges. The coupling performance of the 1.5 m wide 30-element comb-line traveling-wave antenna has been consistent with expectations based on the 2015–2016 experiments on DIII-D with a low-power 12-element prototype (Pinsker et al 2018 Nucl. Fusion 58 106007). The conditioning process that was necessary to carry out high-power experiments is discussed; rf-specific impurities have not been observed. Parametric decay instabilities have been observed and are being investigated as a potential edge absorption mechanism (Porkolab et al 2023 AIP Conf. Proc. 2984 070004).
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Investigating the effect of B T direction on W source-to-core pathways during the SAS-VW campaign on DIII-D
Experiments using the V-shaped closed slot tungsten (W) coated SAS-VW divertor in DIII-D studied the effects of the BT direction on core contamination of eroded tungsten from a closed slot divertor configuration. Core W content is inferred using soft-X ray tomography (SXR) and vacuum ultraviolet spectroscopy (SPRED), while W divertor erosion is inferred from visible spectroscopy of W emission (400.9 nm) measured by in-slot filterscopes (filtered photo-multipliers). Post-mortem analysis from the campaign discovered tile misalignment leading to suspected pronounced leading-edge erosion in the unfavorable BT direction (ion B ⃗×∇B ⃗ drift away from divertor) likely not captured by diagnostics. However, empirical findings show up to ~2-3x larger core contamination in the favorable BT direction even considering no additional W erosion from leading edges. A “source-to-core efficiency factor” is derived to estimate the effects of leading-edge erosion and compare W contamination for two pairs of H-mode discharges in opposite BT directions. While having differing absolute parameters, similar core impurity density gradients suggest comparable core impurity transport. These results show that favorable BT may have stronger source-to-core pathways for W impurities sourced from the outer divertor region. Possible explanations could include the effects of E ⃗×B ⃗ drifts on W transport in the scrape-off-layer (SOL) as well as previously determined fast SOL inner target directed flows in favorable BT.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
High performance power handling in the absence of an H-mode edge in negative triangularity DIII-D plasmas
Abstract Experiments performed during strongly-shaped high-power diverted negative triangularity (NT) experiments in DIII-D achieved detached divertor conditions and a transient-free edge, showcasing the potential for application of NT to a core-edge integrated reactor-like scenario and providing the first characterization of the parametric dependencies for detachment onset. Detached divertor conditions will be required in future devices to mitigate divertor heat fluxes. Access to dissipative divertor conditions was investigated via an increase in upstream density. Detachment onset at the outer strike point was achieved with H-mode level confinement H 98 − y 2 ∼ 1 and reactor-relevant normalized pressures β N ∼ 2 . Confinement degradation was observed with deeper detachment, associated with the loss of an electron temperature pedestal. Differences in geometry, radial transport, impact of cross field drifts are discussed to explain differences in access to detachment in NT discharges. Higher normalized densities, with respect to equivalent discharges in positive triangularity, were necessary to achieve detachment, partially explained by the shorter parallel connection length to the targets. The effect of cross-field particle drifts ( E × B , B × ∇ B ) on access to detachment was demonstrated by the lower upstream density needed to access detachment with ion B × ∇ B drift directed outside of the active divertor (Greenwald fraction f Gw ∼ 0.9–1.0 vs f Gw ∼ 1.3). The upstream density at detachment onset was observed to increase linearly with plasma current with ion B × ∇ B drift into the divertor, consistent with the observed narrowing of the scrape-off layer heat flux width λ q . Edge fluid simulations capture separatrix densities needed to achieve detachment in NT plasma and their dependence on drift direction. The ability to reproduce detachment dynamics in NT plasma increases the confidence in future design studies for NT divertors.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Reversed-direction 2-point modelling applied to divertor conditions in DIII-D *
Abstract A predictive form of the extended 2-point model known as the ‘reverse 2-point model’, Rev2PM, is applied to a range of detachment levels in the open lower divertor of DIII-D, showing that the experimentally measured electron temperature ( T e ) and pressure ( p e ) at the divertor entrance can be calculated within 50% from target measurements, if and only if a posteriori corrections for convective heat flux are included in the model. Unlike the standard 2-point model, the Rev2PM calculates upstream scrape-off layer (SOL) quantities (such as separatrix T e and p e ) from target conditions (such as T e and parallel heat flux), with volumetric power and momentum losses depending solely on target T e . The Rev2PM is tested against a database of DIII-D inter-ELM divertor Thomson scattering measurements, built from a series of 6 MW, 1.3 MA, LSN H-mode discharges with varied main ion density, drift direction, and nitrogen puffing rate. Measured target T e ranged from 0.4–25 eV over this database, and upstream T e ranged from 5–60 eV. Poor agreement is found between upstream measurements and Rev2PM calculations that assume purely conductive parallel heat transport. However, introducing a posteriori corrections to account for convective heat transport brings the Rev2PM calculations within 50% of the measured upstream values across the dataset. These corrections imply that up to 99% of the parallel heat flux is carried by convection in detached conditions in the DIII-D open lower divertor, though further work is required to assess any potential dependencies on device size or divertor closure.
2-point model↗
Spectroscopic measurement of increases in hydrogen molecular rotational temperature with plasma-facing surface temperature and due to collisional-radiative processes in tokamaks
Abstract Spatially resolved rotational temperature of ground state hydrogen molecules desorbed from plasma-facing surface was measured in QUEST, LTX-β, and DIII-D tokamaks, and the increases of the rotational temperature with the surface temperature and due to collisional-radiative processes in the plasmas were evaluated. The increase due to collisional-radiative processes was calculated by solving rate equations considering electron and proton collisional excitation and deexcitation and spontaneous emission. The calculation results suggest a high sensitivity for the rotational temperature to electron and proton densities, but a negligible sensitivity to the electron, proton, and surface temperatures. In the three tokamaks with different plasma parameters and plasma-facing surface materials, the spatial profile of the rotational temperature was estimated using Fulcher-α emission lines (600–608 nm). In QUEST, the spatial profile of the rotational temperature was estimated from spatially resolved spectra. In the other tokamaks, the rotational temperature was evaluated assuming a single point emission with a location determined from the Fulcher-α emission profile as measured with a filtered camera. In metal-walled devices QUEST and LTX-β, the rotational temperature increased with the surface temperature, and the calculated collisional-radiative increase is consistent with measured increase assuming that the rotational temperature at the surface is approximately 500–600 K higher than the surface temperature. In DIII-D with carbon walls, a larger collisional-radiative increase than the other tokamaks was observed because of the higher density leading to a large difference from the calculated increase compared to the other smaller tokamaks. Measurement of the Fulcher-α emission profile with higher spatial resolution in DIII-D may reduce the difference and reveal the effect of the surface temperature on the rotational temperature. These results show the increases in the rotational temperature with the surface temperature and due to the collisional-radiative processes.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Study on divertor detachment and pedestal characteristics in the DIII-D upper closed divertor
Abstract Experiments performed in DIII-D demonstrate that higher plasma current and heating power combined with impurity seeding facilitate the achievement of divertor detachment with a higher pedestal pressure and higher plasma performance in H-mode plasmas with a baffled closed divertor compared with an open divertor. Dedicated experiments were carried out to study the impact of power, plasma current and impurity seeding on divertor detachment with ion B × ∇ B directed into the divertor favorable for the L–H transition. With a factor of three variation in heating power and with only D 2 puffing, no significant difference in the separatrix density at detachment onset was found. The higher heating power leads to higher impurity concentration and wider scrape-off layer (SOL) width, and reduces the detachment onset density to one similar to that in lower-power plasmas. Higher current requires higher pedestal and line-averaged densities to achieve divertor detachment; however, the increase in separatrix density at increasing plasma current is found to be less pronounced. Initial calculations found that both power scan and plasma current scan datasets are qualitatively consistent with theory after considering the change in impurity concentration and heat flux width. This also motivates the future extensive study of transport and divertor impurity behavior in order to have a quantitative comparison between experiment and theory. Compared with an open divertor, a closed divertor facilitates detachment onset at ∼40% lower line-averaged plasma density. Additional N 2 seeding facilitates the achievement of detachment at a lower separatrix density and thus a higher pedestal temperature, which is beneficial for advanced tokamak scenarios. Higher heating power requires a higher N 2 puffing rate to achieve the same degree of detachment, while a higher N 2 puffing rate leads to lower detachment onset line-averaged density, both of which agree with theory. In contrast to the narrower pedestal in an open divertor approaching detachment, the pedestal density width in a closed divertor increases with density. The density gradient increases with line-averaged density at higher plasma current, but remains nearly unchanged at lower plasma current. In particular, compared with discharges with low power, at high heating power the pedestal density gradient is much weaker, while the SOL density is significantly higher and wider. At the same plasma current, both pedestal pressure gradient and temperature gradient decrease linearly with the line-averaged density but remain similar across different heating powers. Even with different plasma current and heating power, the normalized pressure gradient remains identical. As a result, achievement of divertor detachment with a higher pedestal pressure and higher plasma performance is shown in a closed divertor, which is important for improving core–edge integration as one of the critical issues for future tokamak fusion reactors.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Validation of EDGDE2D-EIRENE predicted 2D distributions of electron temperature and density against divertor Thomson scattering measurements in the low-field side divertor leg in DIII-D
Comparisons of profiles of the electron temperature (T e ), density (n e ) and pressure (p e ) measured with Divertor Thomson Scattering in DIII-D low-confinement mode discharges to predictions from the edge fluid code EDGE2D-EIRENE show that the models implemented in EDGE2D-EIRENE predict the measurements within their collective uncertainties if the T e at the separatrix (T e,sep ) is 10 eV, or higher. The simulations do not predict, however, the peaked T e and ne profiles measured adjacent to the target plate when T e,sep , is below 10 eV, i.e., for the plasma downstream from the region of ionization of deuterium atoms. Inclusion of cross-field drifts and a five-fold reduction of radial transport cannot reconcile the discrepancy between the measurements and predictions.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Integration of high confinement, high poloidal beta plasma with dual radiated power and detachment controls for divertor protection and ELM suppression
Divertor detachment without serious core confinement quality loss in DIII-D’s high poloidal β scenario has been combined with impurity-induced ELM mitigation without disruption. Use of Ne previously granted access to a detached, non-ELMing regime that retained high confinement quality due to stimulation of Internal Transport Barrier (ITB) growth, but suffered from on-going core fuel dilution and high disruptivity. Excess Ne accumulation in the core plasma has now been avoided by feeding back core radiated power ($P_{rad}$) measurements to control Ne seeding, rather than using attachment fraction ($A_{frac}$) control with Ne; this also reduces disruptivity. At the same time, N 2 seeding is used in a feedback loop with $A_{frac}$ measurements, which previously posed low disruption risk. In this way, the effect of Ne in the core is managed while avoiding excess seeding, and N 2 acts to correct for any excess heat exhaust that might interfere with detachment. The average Ne flow rate was 38% of what was used in pure Ne $A_{frac}$ control, plus average N 2 flow that was 43% of pure N 2 $A_{frac}$ control, even while meeting an even deeper detachment target. Meanwhile, a steep pressure gradient in the core plasma reduces sensitivity to impurity-induced degradation of the pedestal and reasonable confinement quality was maintained despite operational challenges that blocked formation of an ITB in these experiments.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Recoil imaging for dark matter, neutrinos, and physics beyond the Standard Model
Recoil imaging entails the detection of spatially resolved ionization tracks generated by particle interactions. This is a highly sought-after capability in many classes of detector, with broad applications across particle and astroparticle physics. However, at low energies, where ionization signatures are small in size, recoil imaging only seems to be a practical goal for micro-pattern gas detectors. This white paper outlines the physics case for recoil imaging, and puts forward a decadal plan to advance towards the directional detection of low-energy recoils with sensitivity and resolution close to fundamental performance limits. The science case covered includes: the discovery of dark matter into the neutrino fog, directional detection of sub-MeV solar neutrinos, the precision study of coherent-elastic neutrino-nucleus scattering, the detection of solar axions, the measurement of the Migdal effect, X-ray polarimetry, and several other applied physics goals. We also outline the R&D programs necessary to test concepts that are crucial to advance detector performance towards their fundamental limit: single primary electron sensitivity with full 3D spatial resolution at the $\sim$100 micron-scale. These advancements include: the use of negative ion drift, electron counting with high-definition electronic readout, time projection chambers with optical readout, and the possibility for nuclear recoil tracking in high-density gases such as argon. We also discuss the readout and electronics systems needed to scale-up such detectors to the ton-scale and beyond.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Impact of edge harmonic oscillations on the divertor heat flux in NSTX
Previously, ELM-free and inter-ELM divertor peak heat flux reduction induced by an edge harmonic oscillation (EHO) was observed in NSTX (K.F. Gan et al., 2017 Nucl. Fusion 57 126053). This paper introduces new analysis of the EHO impact on the divertor heat flux. It was found that enhanced edge turbulence significantly altered the divertor heat flux footprint in NSTX H-modes, relative to ELM-free discharges. When the background edge fluctuation level was low, the EHO significantly increased the heat flux width and decreased the divertor peak heat flux. When the background edge fluctuation level was high, the EHO actually increased the divertor peak heat flux. As a result, it was also found that the heat flux width increased with increasing frequency of the EHO.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Design and physics basis for the upcoming DIII-D SAS-VW campaign to quantify tungsten leakage and transport in a new slot divertor geometry
A set of experiments are planned to exploit the high SOL collisionality enabled by a tightly baffled slot divertor geometry to suppress tungsten leakage in DIII-D. A toroidal row of graphite tiles from the Small Angle Slot (SAS) divertor is being coated with 10–15 μ m of tungsten. New spectroscopic viewing chords with in-vacuo optics will measure the W gross erosion source from the divertor surface with high spatial and temporal resolution. In parallel, the bottom of the SAS divertor is changed from a flat to a ‘V’ shape. New SOLPS-ITER/DIVIMP simulations conducted with drifts using the planned ‘V’ shape predict a substantial reduction in W sourcing and SOL accumulation in either B × ∇B direction relative to either the old SAS divertor shape or the open, lower divertor. Dedicated studies are planned to carefully characterize the level of W sourcing, leakage, and scrape-off-layer (SOL) accumulation in DIII-D over a wide range of plasma scenarios. Various actuators will be assessed for their efficacy in further reducing high-Z impurity sources and leakage from the slot divertor geometry. Finally, this coupled code-experiment validation effort will be used to stress-test physics models and build confidence in extrapolations to advanced, high-Z divertor geometries for next-step devices.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Micro-trench measurements of the net deposition of carbon impurity ions in the DIII-D divertor and the resulting suppression of surface erosion
In this work, we report carbon impurity ion incident angles and deposition rates, along with silicon erosion rates, from measurements of micro-engineered trenches on a silicon surface exposed to L-mode deuterium plasmas at the DIII-D divertor. Post exposure ex-situ analysis determined elemental maps and concentrations, carbon deposition thicknesses, and erosion of silicon surfaces. Carbon deposition profiles on the trench floor showed carbon ion shadowing that was consistent with ERO calculations of average carbon ion angle distributions (IADs) for both polar and azimuthal angles. Measured silicon net erosion rates negatively correlated with the deposited carbon concentration at different locations. Differential erosion of surfaces on two different ion-downstream trench slope structures suggested that carbon deposition rate is affected by the carbon ion incident angle and significantly suppressed the surface erosion. The results suggest the C impurity ion incident angles, determined by the IADs and surface morphology, strongly affect erosion rates as well as the main ion (D, T, He) incident angles.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Experimental verification of ion impact angle distribution at divertor surfaces using micro-engineered targets on DiMES at DIII-D
Not Available
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Impact of divertor material on neutral recycling and discharge fueling in DIII-D.
Abstract not provided.
Bykov, I.↗