Carbon corrosion in low-temperature CO 2 electrolysis systems
Mitigation of carbon corrosion, or the use of non-carbon based anodes, is required to achieve the necessary durability for industrial CO 2 electrolysis.
Engineering topics
Publications and source records attributed to McNeary, W. Wilson.
Mitigation of carbon corrosion, or the use of non-carbon based anodes, is required to achieve the necessary durability for industrial CO 2 electrolysis.
Reactive carbon dioxide capture (RCC) is a process where carbon dioxide (CO 2 ) is captured from a mixed gas stream (such as air) and converted to products without first performing a separation step to concentrate the CO 2 . Here, in this work, zeolite dual-functional materials (ZFMs) are introduced and evaluated for simulated RCC. The studied ZFMs feature high surface area, crystalline, microporous zeolite faujasite (FAU) as the support. Sodium oxide (“Na 2 O”) is impregnated as an effective capture agent capable of scavenging low concentration CO 2 (1,000 ppm). Exchanged and impregnated sodium on FAU chemisorbs CO 2 as carbonates and bicarbonates but does not promote the conversion of sorbed CO 2 to products when heated in hydrogen. The addition of Ru promotes the formation of formates, while the addition of Pt generates carbonyl surface species when heated in hydrogen. The active metal then promotes extremely high selectivity for CO 2 hydrogenation to either methane on Ru catalyst (~150 °C) or carbon monoxide on Pt catalyst (~200 °C) when heated in reducing atmospheres.
A novel RCC process using modified CZA DFMs to produce renewable MeOH is presented. K/CZA provides exceptionally high productivity of MeOH compared to previously reported attempts of RCC to MeOH.
Polymer electrolyte membrane fuel cells (PEMFCs) produce electricity with only heat and water as byproducts, but sluggish kinetics of the oxygen reduction reaction (ORR) at the cathode and durability limitations restrict widespread commercialization, motivating the development of advanced catalysts. In this research, extended-surface platinum nickel (PtNi) nanowires (NWs) synthesized using the scalable atomic layer deposition (ALD) technique are investigated with the goal of exploring the durability benefits of high-aspect-ratio electrocatalysts and the tunability of beneficial kinetic properties. The surface and bulk composition and the structure of the PtNi NWs were investigated as a function of a series of postsynthesis modifications. The results from a combination of electron microscopy and X-ray spectroscopy characterization techniques were correlated to electrochemical performance to gain a comprehensive understanding of the structure-property-performance relationships. The robust structure of the ALD-derived NWs enabled additional postsynthesis optimization steps, which were not possible with previous-generation materials synthesized via spontaneous galvanic displacement, resulting in a catalyst with beneficial properties for catalyst kinetics as well as improved durability. Our study demonstrates potential pathways toward further improving the performance of this class of materials through optimization of bulk and surface properties of the catalyst.
Heterogeneous catalysts are a key enabler of the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions in many biomass conversion processes lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Next-generation catalysts must be developed to address these stability challenges. This presentation will discuss ongoing work between the Catalytic Carbon Transformation and Scale-Up Center at NREL and various industrial partners to develop scalable and cost-effective atomic layer deposition (ALD) coatings for improving the performance of biomass conversion catalysts. The substantial focus will be devoted to the benefits of TiO2 ALD coatings on supported Pd hydrogenation catalysts. Ten cycles of TiO2 ALD were found to dramatically improve the activity of a conventional Pd/Al2O3 catalyst towards aromatic hydrogenation, despite partial coverage of the Pd sites by the ALD layer. Subsequent advanced characterization and atomic-scale computational modeling revealed that the ALD coating weakened the adsorption strength of hydrogenation surface intermediates, leading to higher reaction rates. Reaction testing after exposure to sulfur impurities, high temperature oxidation, and hydrothermal treatment demonstrated the improved stability of the ALD-coated catalyst. Additionally, the ALD synthesis process was found to be scalable over two orders of magnitude with minimal deviation in synthesized catalyst properties. These results were contextualized with cost models of industrial ALD coating and aromatic hydrogenation processes to further refine the value proposition of ALD coatings. Given the demonstrated improvements in hydrogenation, TiO2 ALD coatings have also been applied to supported Pt catalysts for use in other biomass conversion reactions, such as hydrodeoxygenation for the production of sustainable aviation fuel (SAF) and the oxidation of glucose to bio-derived gluconic acid. Recent findings from these experimental campaigns will also be shared. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts, and this work constitutes an important examination of the impact of ALD coatings in a variety of reaction environments.
Heterogeneous catalysts are a key enabler of the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions in many biomass conversion processes lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Next-generation catalysts must be developed to address these stability challenges. This presentation will discuss ongoing work between the Catalytic Carbon Transformation & Scale-Up Center at NREL and various industrial partners to develop scalable, cost-effective atomic layer deposition (ALD) coatings for improving the performance of biomass conversion catalysts. Substantial focus will be devoted to the benefits of TiO2 ALD coatings on supported Pd hydrogenation catalysts. Ten cycles of TiO2 ALD were found to dramatically improve the activity of a conventional Pd/Al2O3 catalyst towards aromatic hydrogenation, despite partial coverage of the Pd sites by the ALD layer. Subsequent advanced characterization and atomic-scale computational modeling revealed that the ALD coating influenced the adsorption strength of hydrogenation surface intermediates in unexpected ways, leading to higher reaction rates. Reaction testing after exposure to sulfur impurities, high temperature oxidation, and hydrothermal treatment demonstrated the improved stability of the ALD-coated catalyst. Additionally, the ALD synthesis process was found to be scalable over two orders of magnitude with minimal deviation in synthesized catalyst properties. These results were contextualized with cost models of industrial ALD coating and aromatic hydrogenation processes to further refine the value proposition of ALD coatings. Given the demonstrated improvements in hydrogenation, TiO2 ALD coatings have also been applied to supported Pt catalysts for use in other biomass conversion reactions, such as hydrodeoxygenation for production of sustainable aviation fuel (SAF) and the oxidation of glucose for bio-derived gluconic acid. Recent findings from these experimental campaigns will also be shared. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts and this work constitutes an important examination of the impact of ALD coatings in a variety of reaction environments.
Heterogeneous catalysts are a key enabler of the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions in many biomass conversion processes lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Next-generation catalysts must be developed to address these stability challenges. This presentation will discuss ongoing work between the Catalytic Carbon Transformation and Scale-Up Center at NREL and various industrial partners to develop scalable and cost-effective atomic layer deposition (ALD) coatings for improving the performance of biomass conversion catalysts. The substantial focus will be devoted to the benefits of TiO2 ALD coatings on supported Pd hydrogenation catalysts. Ten cycles of TiO2 ALD were found to dramatically improve the activity of a conventional Pd/Al2O3 catalyst towards aromatic hydrogenation, despite partial coverage of the Pd sites by the ALD layer. Subsequent advanced characterization and atomic-scale computational modeling revealed that the ALD coating weakened the adsorption strength of hydrogenation surface intermediates, leading to higher reaction rates. Reaction testing after exposure to sulfur impurities, high temperature oxidation, and hydrothermal treatment demonstrated the improved stability of the ALD-coated catalyst. Additionally, the ALD synthesis process was found to be scalable over two orders of magnitude with minimal deviation in synthesized catalyst properties. These results were contextualized with cost models of industrial ALD coating and aromatic hydrogenation processes to further refine the value proposition of ALD coatings. Given the demonstrated improvements in hydrogenation, TiO2 ALD coatings have also been applied to supported Pt catalysts for use in other biomass conversion reactions, such as hydrodeoxygenation for the production of sustainable aviation fuel (SAF) and the oxidation of glucose to bio-derived gluconic acid.
Hydrogenation of aromatic molecules in fossil- and bio-derived fuels is essential for decreasing emissions of harmful combustion products and addressing growing concerns around urban air pollution. In this work, we used atomic layer deposition to significantly enhance the hydrogenation performance of a conventional supported Pd catalyst by applying an ultrathin coating of TiO2 in a scalable powder coating process. The TiO2-coated catalyst showed substantial gains in the conversion of multiple aromatic molecules, including a 5-fold improvement in turnover frequency versus the uncoated catalyst in the hydrogenation of naphthalene. This activity enhancement was maintained upon scaling the coating synthesis process from 3 to 100 g. Based on the results from Xray photoelectron spectroscopy, X-ray absorption spectroscopy, and computational modeling, the activity enhancement was attributed to ensemble effects resulting from partial TiO2 coverage of the Pd surface rather than fundamental changes to the Pd electronic structure. Additional durability testing confirmed that the TiO2 coating improved the thermal and hydrothermal stability of the catalyst as well as tolerance toward sulfur impurities in the reactant stream. Using an economic model of an industrial deep hydrogenation process, we found that an increase in catalyst activity or lifetime of 2× would justify even a relatively high estimate for the cost of TiO2 atomic layer deposition coatings at scale
Heterogeneous catalysts are an essential tool in the transition towards a sustainable, bio-based economy for fuels and chemicals. However, many key biomass conversion processes utilize harsh conditions that lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Active site poisoning resulting from the relatively high sulfur content of most biomass feedstocks further compounds these durability problems. Next-generation catalysts must be developed to address these stability challenges. In this work, we have used atomic layer deposition (ALD), to modify a conventional Pd/Al2O3 hydrogenation catalyst and generate improvements in its stability and sulfur tolerance, as well as overall catalyst activity. Ten cycles of TiO2ALD were applied to Pd/Al2O3 using a proprietary coating process developed by industry partners. The coated catalyst (10cTiO2), alongside uncoated Pd/TiO2 and Pd/Al2O3 controls, was characterized in-depth and naphthalene hydrogenation was used as a probe reaction to assess activity. The 10cTiO2 catalyst was observed to be significantly more active towards hydrogenation than uncoated Pd/Al2O3, despite evidence that the ALD coating suppressed chemisorption uptake through coverage of Pd. In order to reconcile these seemingly contradictory findings, interactions between the Pd nanoparticles and TiO2ALD coating were investigated via XAS and computational modeling. The catalysts were also assessed for their sulfur tolerance, thermal stability, and hydrothermal stability. Each of these catalyst stability parameters was enhanced by application of the TiO2ALD layer; the mechanisms by which the layer may have mitigated these degradation processes will be discussed. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts and this work constitutes an important examination of the expected and unexpected benefits of applying TiO2ALD coatings to supported Pd hydrogenation catalysts.
NREL is located in the beautiful scenic Colorado, but it has a dirty secret. It is among one the top 10 worst U.S. cities for hazardous air pollution, particularly in Denver. The Denver metro area has been out of compliance with EPA's limits on ozone pollution for decades and it's gotten so bad that at the end of last year the EPA moved our designation from moderate non-obtainment to serious non-obtainment. There's a lot of work that needs to be done in Denver and around the world to reduce air pollution in urban areas.
Heterogeneous catalysts are an essential tool in the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions (e.g., high temperatures, acidity, oxidizing/reducing environments) of many key biomass conversion processes give rise to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Active site poisoning due to the relatively high sulfur content of most biomass feedstocks further compounds these durability problems. Next-generation catalysts must be developed to address these stability challenges. In this work, we used a scalable atomic layer deposition (ALD) process to modify conventional Pd-based hydrogenation catalysts to generate significant performance improvements. TiO2 ALD coatings were found to increase the activity of Pd/Al2O3 catalysts towards naphthalene hydrogenation; additionally, these coatings improved the catalyst's resistance to sulfur poisoning and thermal stability under oxidative calcination. Additional work in which Al2O3 ALD coatings were applied to Pd/TiO2 catalysts for muconic acid hydrogenation found similar stability benefits, including improved resistance to Pd leaching in the acidic environment. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts and this work constitutes an important examination of applying ALD coatings to supported Pd hydrogenation catalysts.
The deposition of alumina ALD films on Li ion battery cathode particles is known to enhance the cycling stability of lithium ion batteries fabricated from those coated particles. It is commonly assumed that the film on the particles is of uniform thickness and is optimally thin enough to facilitate lithium diffusion while blocking side reactions of the electrolyte with the cathode substrate. Here, we elucidate the nature of thin alumina films deposited with between 2 and 15 ALD cycles on lithium nickel manganese cobalt oxide cathode precursor particles. Low energy ion scattering (LEIS) and secondary ion mass spectroscopy (SIMS) methods were used to characterize thin (<2 nm) films that were deposited by ALD. Surface analysis showed that low-cycle number ALD films were not uniform nor uniformly thick over the surface of the cathode particles and that alumina ALD preferentially deposited on transition metal bound sites on the cathode particle surface and coated Li on the surface to a lesser extent. Lithium was found to still be present on the cathode powder surface, even after 10 ALD cycles. Contrary to current supposition, low-cycle ALD appeared to improve the cycling stability of battery cathode active materials through this preferential growth that stabilized the transition metal oxides in the presence of electrolyte without blocking lithium intercalation pathways. This is the first study to determine that Li remains exposed on the as-synthesized surface of ALD coated cathode particles and that the ALD film is nonuniform and nonuniformly thick when less than 10 ALD cycles are used.