Search NASASearch

Engineering topics

Mcclain, Charles R.

Publications and source records attributed to Mcclain, Charles R..

At least 19 records

SeaWiFS technical report series. Volume 28: SeaWiFS algorithms, part 1

This document provides five brief reports that address several algorithm investigations sponsored by the Calibration and Validation Team (CVT) within the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Project. This volume, therefore, has been designated as the first in a series of algorithm volumes. Chapter 1 describes the initial suite of masks, used to prevent further processing of contaminated radiometric data, and flags, which are employed to mark data whose quality (due to a variety of factors) may be suspect. In addition to providing the mask and flag algorithms, this chapter also describes the initial strategy for their implementation. Chapter 2 evaluates various strategies for the detection of clouds and ice in high latitude (polar and sub-polar regions) using Coastal Zone Color Scanner (CZCS) data. Chapter 3 presents an algorithm designed for detecting and masking coccolithosphore blooms in the open ocean. Chapter 4 outlines a proposed scheme for correcting the out-of-band response when SeaWiFS is in orbit. Chapter 5 gives a detailed description of the algorithm designed to apply sensor calibration data during the processing of level-1b data.

Hooker, Stanford B.

SeaWiFS technical report series. Volume 23: SeaWiFS prelaunch radiometric calibration and spectral characterization

Based on the operating characteristics of the Sea-viewing Wide Field-of-view Sensor (SeaWiFS), calibration equations have been developed that allow conversion of the counts from the radiometer into Earth-existing radiances. These radiances are the geophysical properties the instrument has been designed to measure. SeaWiFS uses bilinear gains to allow high sensitivity measurements of ocean-leaving radiances and low sensitivity measurements of radiances from clouds, which are much brighter than the ocean. The calculation of these bilinear gains is central to the calibration equations. Several other factors within these equations are also included. Among these are the spectral responses of the eight SeaWiFS bands. A band's spectral response includes the ability of the band to isolate a portion of the electromagnetic spectrum and the amount of light that lies outside of that region. The latter is termed out-of-band response. In the calibration procedure, some of the counts from the instrument are produced by radiance in the out-of-band region. The number of those counts for each band is a function of the spectral shape of the source. For the SeaWiFS calibration equations, the out-of-band responses are converted from those for the laboratory source into those for a source with the spectral shape of solar flux. The solar flux, unlike the laboratory calibration, approximates the spectral shape of the Earth-existing radiance from the oceans. This conversion modifies the results from the laboratory radiometric calibration by 1-4 percent, depending on the band. These and other factors in the SeaWiFS calibration equations are presented here, both for users of the SeaWiFS data set and for researchers making ground-based radiance measurements in support of Sea WiFS.

Barnes, Robert A.

SeaWiFS Technical Report Series. Volume 22: Prelaunch Acceptance Report for the SeaWiFS Radiometer

The final acceptance, or rejection, of the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) will be determined by the instrument's on-orbit operation. There is, however, an extensive set of laboratory measurements describing the operating characteristics of the radiometer. Many of the requirements in the Ocean Color Data Mission (OCDM) specifications can be checked only by laboratory measurements. Here, the calibration review panel examines the laboratory characterization and calibration of SeaWiFS in the light of the OCDM performance specification. Overall, the performance of the SeaWiFS instrument meets or exceeds the requirements of the OCDM contract in all but a few unimportant details. The detailed results of this examination are presented here by following the outline of the specifications, as found in the Contract. The results are presented in the form of requirements and compliance pairs. These results give conclusions on many, but not all, of the performance specifications. The acceptance by this panel of the performance of SeaWiFS must only be considered as an intermediate conclusion. The ultimate acceptance (or rejection) of the SeaWiFS data set will rely on the measurements made by the instrument on orbit.

Hooker, Stanford B.

SeaWiFS technical report series. Volume 22: Prelaunch acceptance report for the SeaWFS radiometer

The final acceptance, or rejection, of the Sea-viewing Wide field-of-view Sensor (SeaWiFS) will be determined by the instrument's on-orbit operation. There is, however, an extensive set of laboratory measurements describing the operating characteristics of the radiometer. Many of the requirements in the Ocean Color Data Mission (OCDM) specifications can be checked only by laboratory measurements. Here, the calibration review panel (composed of the authors of this technical memorandum) examines the laboratory characterization and calibration of SeaWiFS in the light of the OCDM performance specification. Overall, the performance of the SeaWiFS instrument meets or exceeds the requirements of the OCDM contract in all but a few unimportant details. The detailed results of this examination are presented here by following the outline of the specifications, as found in the Contract. The results are presented in the form of requirements and compliance pairs. These results give conclusions on many, but not all, of the performance specifications. The acceptance of this panel of the performance of SeaWiFS must only be considered as an intermediate conclusion. The ultimate acceptance (or rejection) of the SeaWiFS data set will rely on the measurements made by the instrument on orbit.

Hooker, Stanford B.

SeaWiFS technical report series. Volume 19: Case studies for SeaWiFS calibration and validation, part 2

This document provides brief reports, or case studies, on a number of investigations and data set development activities sponsored by the Calibration and Validation Team (CVT) within the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Project. Chapter 1 is a comparison with the atmospheric correction of Coastal Zone Color Scanner (CZCS) data using two independent radiative transfer formulations. Chapter 2 is a study on lunar reflectance at the SeaWiFS wavelengths which was useful in establishing the SeaWiFS lunar gain. Chapter 3 reports the results of the first ground-based solar calibration of the SeaWiFS instrument. The experiment was repeated in the fall of 1993 after the instrument was modified to reduce stray light; the results from the second experiment will be provided in the next case studies volume. Chapter 4 is a laboratory experiment using trap detectors which may be useful tools in the calibration round-robin program. Chapter 5 is the original data format evaluation study conducted in 1992 which outlines the technical criteria used in considering three candidate formats, the hierarchical data format (HDF), the common data format (CDF), and the network CDF (netCDF). Chapter 6 summarizes the meteorological data sets accumulated during the first three years of CZCS operation which are being used for initial testing of the operational SeaWiFS algorithms and systems and would be used during a second global processing of the CZCS data set. Chapter 7 describes how near-real time surface meteorological and total ozone data required for the atmospheric correction algorithm will be retrieved and processed. Finally, Chapter 8 is a comparison of surface wind products from various operational meteorological centers and field observations. Surface winds are used in the atmospheric correction scheme to estimate glint and foam radiances.

Hooker, Stanford B.

SeaWiFS technical report series. Volume 20: The SeaWiFS bio-optical archive and storage system (SeaBASS), part 1

This document provides an overview of the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Bio-Optical Archive and Storage System (SeaBASS), which will serve as a repository for numerous data sets of interest to the SeaWiFS Science Team and other approved investigators in the oceanographic community. The data collected will be those data sets suitable for the development and evaluation of bio-optical algorithms which include results from SeaWiFS Intercalibration Round-Robin Experiments (SIRREXs), prelaunch characterization of the SeaWiFS instrument by its manufacturer -- Hughes/Santa Barbara Research Center (SBRC), Marine Optical Characterization Experiment (MOCE) cruises, Marine Optical Buoy (MOBY) deployments and refurbishments, and field studies of other scientists outside of NASA. The primary goal of the data system is to provide a simple mechanism for querying the available archive and requesting specific items, while assuring that the data is made available only to authorized users. The design, construction, and maintenance of SeaBASS is the responsibility of the SeaWiFS Calibration and Validation Team (CVT). This report is concerned with documenting the execution of this task by the CVT and consists of a series of chapters detailing the various data sets involved. The topics presented are as follows: 1) overview of the SeaBASS file architecture, 2) the bio-optical data system, 3) the historical pigment database, 4) the SIRREX database, and 5) the SBRC database.

Hooker, Stanford B.

Dynamics of the transition zone in coastal zone color scanner-sensed ocean color in the North Pacific during oceanographic spring

A transition zone in phytoplankton concentration running across the North Pacific basin at 30 deg to 40 deg north latitude corresponds to a basin-wide front in surface chlorophyll observed in a composite of coastal zone color scanner (CZCS) images for May, June, and July 1979-1986. This transition zone with low chlorophyll to the south and higher chlorophyll to the north can be simulated by a simple model of the concentration of phytoplankton, zooplankton, and dissolved nutrient (nitrate) in the surface mixed layer of the ocean applied to the North Pacific basin for the climatological conditions during oceanographic springtime (May, June, and July). The model is initialized with a 1 deg x 1 deg gridded estimate of wintertime (February, March, and April) mixed layer nitrate concentrations calculated from an extensive nutrient database and a similarly gridded mixed layer depth data set. Comparison of model predictions with CZCS data provides a means of evaluating the dynamics of the transition zone. We conclude that in the North Pacific, away from major boundary currents and coastal upwelling zones, wintertime vertical mixing determines the total nutrient available to the plankton ecosystem in the spring. The transition zone seen in basin-scale CZCS images is a reflection of the geographic variation in the wintertime mixed layer depth and the nitracline, leading to a latitudinal gradient in phytoplankton chlorophyll.

Glover, David M.

SeaWiFS technical report series. Volume 13: Case studies for SeaWiFS calibration and validation, part 1

Although the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Calibration and Validation Program relies on the scientific community for the collection of bio-optical and atmospheric correction data as well as for algorithm development, it does have the responsibility for evaluating and comparing the algorithms and for ensuring that the algorithms are properly implemented within the SeaWiFS Data Processing System. This report consists of a series of sensitivity and algorithm (bio-optical, atmospheric correction, and quality control) studies based on Coastal Zone Color Scanner (CZCS) and historical ancillary data undertaken to assist in the development of SeaWiFS specific applications needed for the proper execution of that responsibility. The topics presented are as follows: (1) CZCS bio-optical algorithm comparison, (2) SeaWiFS ozone data analysis study, (3) SeaWiFS pressure and oxygen absorption study, (4) pixel-by-pixel pressure and ozone correction study for ocean color imagery, (5) CZCS overlapping scenes study, (6) a comparison of CZCS and in situ pigment concentrations in the Southern Ocean, (7) the generation of ancillary data climatologies, (8) CZCS sensor ringing mask comparison, and (9) sun glint flag sensitivity study.

Hooker, Stanford B.

An investigation of Ekman upwelling in the North Atlantic

The spatial and temporal variability of the North Atlantic Ekman upwelling fields on seasonal and interannual time scales is investigated on the basis of surface winds from the Fleet Numerical Oceanography Center for 1979-1986. A pronounced minimum in the basin-wide monthly mean vertical Ekman velocities during 1981-1982 is found. It is shown that the primary source of the interannual signal was the region off NW Africa in the vicinity of the Guinea Dome. Other sectors of the basin experienced no significant interannual trends. Hydrographic data and SST data from the NW Africa sector for 1981-1986 indicate a cooling trend beginning in late 1982, consistent with increased upwelling. The fall and winter seasons' mixed layers at the center of the Guinea Dome were deeper in 1984 and 1985 than in previous years. The potential impact of large interannual variations in Ekman upwelling on basin-wide primary productivity is discussed.

Mcclain, Charles R.

SeaWiFS technical report series. Volume 10: Modeling of the SeaWiFS solar and lunar observations

Post-launch stability monitoring of the Sea-viewing Wide Field-of-view Sensor (SeaWifs) will include periodic sweeps of both an onboard solar diffuser plate and the moon. The diffuser views will provide short-term checks and the lunar views will monitor long-term trends in the instrument's radiometric stability. Models of the expected sensor response to these observations were created on the SeaWiFS computer at the National Aeronautics and Space Administration's (NASA) Goddard Space Flight Center (GSFC) using the Interactive Data Language (IDL) utility with a graphical user interface (GUI). The solar model uses the area of intersecting circles to simulate the ramping of sensor response while viewing the diffuser. This model is compared with preflight laboratory scans of the solar diffuser. The lunar model reads a high-resolution lunar image as input. The observations of the moon are simulated with a bright target recovery algorithm that includes ramping and ringing functions. Tests using the lunar model indicate that the integrated radiance of the entire lunar surface provides a more stable quantity than the mean of radiances from centralized pixels. The lunar model is compared to ground-based scans by the SeaWiFS instrument of a full moon in December 1992. Quality assurance and trend analyses routines for calibration and for telemetry data are also discussed.

Woodward, Robert H.

Comment on 'A note on the possible connection between the El Chichon eruption and ocean production in the northwest Arabian Sea during 1982' by A. E. Strong

Strong argues that the El Chichon aerosol cloud resulted in relaxed southwest monsoon circulation and the dramatically reduced seasonal phytoplankton bloom documented in the northwestern Arabian Sea during summer and fall of 1982. It is argued here that Strong's ideas suggest a clear demonstration of an atmosphere-ocean interaction with implications for the ocean's biological CO2 pump. Strong's paper highlights the fundamentally different effects of volcanic aerosols on satellite infrared and visible band observations of the ocean.

Brock, John C.

PC-SEAPAK

Interactive satellite data analysis software package developed for oceanographic research. Program used to process data from Nimbus-7 Coastal Zone Color Scanner and NOAA Advanced Very-High-Resolution Radiometer.

Mcclain, Charles R.

An assessment of the Nimbus-7/CZCS calibration for May 1986 using satellite and in situ data from the Arabian Sea

A hydrographic survey of the central Arabian Sea was conducted in May 1986 and stations were correlated with Nimbus-7/Coastal Zone Color Scanner (CZCS) overpasses. As calibration of the CZCS degraded severely during its lifetime, pigment concentrations from samples at four sites in the Arabian Sea were used to refine the calibration of the CZCS. This vicarious calibration technique provided a final estimate of the sensor's sensitivity loss for sensor Gain 2. Calibration using normalized water-leaving radiance for the 520 nm and 550 nm bands showed considerable final sensor degradation. Future missions must incorporate calibration validation programs in order to maintain derived product accuracy requirements. Profiles of pigment concentration, salinity, temperature, and light attenuation are used to describe the bio-optical characteristics of the Arabian Sea during the intermonsoon period.

Hay, Bernward J.

SeaWiFS calibration and validation plan, volume 3

The Sea-viewing Wide Field-of-view Sensor (SeaWiFS) will be the first ocean-color satellite since the Nimbus-7 Coastal Zone Color Scanner (CZCS), which ceased operation in 1986. Unlike the CZCS, which was designed as a proof-of-concept experiment, SeaWiFS will provide routine global coverage every 2 days and is designed to provide estimates of photosynthetic concentrations of sufficient accuracy for use in quantitative studies of the ocean's primary productivity and biogeochemistry. A review of the CZCS mission is included that describes that data set's limitations and provides justification for a comprehensive SeaWiFS calibration and validation program. To accomplish the SeaWiFS scientific objectives, the sensor's calibration must be constantly monitored, and robust atmospheric corrections and bio-optical algorithms must be developed. The plan incorporates a multi-faceted approach to sensor calibration using a combination of vicarious (based on in situ observations) and onboard calibration techniques. Because of budget constraints and the limited availability of ship resources, the development of the operational algorithms (atmospheric and bio-optical) will rely heavily on collaborations with the Earth Observing System (EOS), the Moderate Resolution Imaging Spectrometer (MODIS) oceans team, and projects sponsored by other agencies, e.g., the U.S. Navy and the National Science Foundation (NSF). Other elements of the plan include the routine quality control of input ancillary data (e.g., surface wind, surface pressure, ozone concentration, etc.) used in the processing and verification of the level-0 (raw) data to level-1 (calibrated radiances), level-2 (derived products), and level-3 (gridded and averaged derived data) products.

Hooker, Stanford B.

SeaWiFS technical report series. Volume 1: An overview of SeaWiFS and ocean color

The purpose of this series of technical reports is to provide current documentation of the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Project activities, instrument performance, algorithms, and operations. This documentation is necessary to ensure that critical information related to the quality and calibration of the satellite data is available to the scientific community. SeaWiFS will bring to the ocean community a welcomed and improved renewal of the ocean color remote sensing capability lost when the Nimbus-7 Coastal Zone Color Scanner (CZCS) ceased operating in 1986. The goal of SeaWiFS, scheduled to be launched in August 1993, is to examine oceanic factors that affect global change. Because of the role of phytoplankton in the global carbon cycle, data obtained from SeaWiFS will be used to assess the ocean's role in this cycle, as well as other biogeochemical cycles. SeaWiFS data will be used to help elucidate the magnitude and variability of the annual cycle of primary production by marine phytoplankton and to determine the distribution and timing of spring blooms. The observations will help to visualize the dynamics of ocean and costal currents, the physics of mixing, and the relationships between ocean physics and large-scale patterns of productivity. The data will help fill the gap in ocean biological observations between those of the CZCS and the upcoming Moderate Resolution Imaging Spectrometer (MODIS) on the Earth Observing System-A (EOS-A) satellite.

Hooker, Stanford B.

A southwest monsoon hydrographic climatology for the Northwestern Arabian Sea

This paper provides a detailed hydrographic climatology for the shallow northwestern Arabian Sea prior to and during the southwest monsoon, presented as multiple-year composite vertical hydrographic sections based on National Oceanographic Data Center historical ocean station data. Temperature and salinity measurements are used to infer the water masses present in the upper 500 m. The hydrographic evolution depicted on bimonthly sections is inferred to result from wind-driven physical processes. In the northwestern Arabian Sea the water mass in the upper 50 m is the Arabian Sea Surface Water. Waters from 50 to 500 m are formed by mixing of Arabian Sea Surface Water with Antarctic and Indonesian intermediate waters. The inflow of Persian Gulf Water does not significantly influence the hydrography of the northwestern Arabian Sea along the Omani coast. Nitrate has a high inverse correlation with temperature and oxygen in the premonsoon thermocline in the depth interval 50-150 m. During the southwest monsoon, coastal upwelling off Oman and adjacent offshore upward Ekman pumping alter the shallow hydrography.

Brock, John C.

Interannual variability in phytoplankton blooms observed in the northwestern Arabian Sea during the southwest monsoon

Interannual changes in the strength and seasonal evolution of the 1979 through 1982 surface-level southwest monsoon winds are related to variations in the summer phytoplankton bloom of the northwestern Arabian Sea by synthesis of satellite ocean-color remote sensing with analysis of in-situ hydrographic and meteorological data sets. The 1979-1981 southwest monsoon phytoplankton blooms in the northwest Arabian Sea peaked during August-September, extended from the Omani coast to about 6 E, and appeared to lag the development of open-sea upwelling by at least 1 month. In all 3 years the bloom was driven by spatially distinct upward nutrient fluxes to the euphotic zone forced by the physical processes of coastal upwelling and offshore Ekman pumping. Coastal upwelling was evident from May through September, yielded the most extreme concentrations of phytoplankton biomass, and along the Omani coast was limited in its impact on upper ocean biological variability to the continental shelf. Ekman pumping stimulated the development of a broad open-ocean component of the southwest monsoon phytoplankton bloom oceanward of the Omani shelf. Phytoplankton biomass on the Omani continental shelf was increased during both the early and late phases of the 1980 southwest monsoon due to stronger coastal upwelling under the most intense southwesterly winds of the four summers investigated. Diminished coastal upwelling during the early phase of the weak 1982 southwest monsoon resulted in a coastal bloom that reached a mean phytoplankton-pigment concentration that was 28 percent of that seen in 1980. The lack of a strong regional northwestern Arabian Sea bloom in late summer 1982 is attributed to the development of persistent, shallow temperature stratification that rendered Ekman pumping less effective in driving upward nutrient fluxes.

Brock, John C.

Analyzing Satellite Images Of The Ocean

PC-SEAPAK is user-interactive software package specifically developed for analysis of data from satellites in oceanographic research. Program used to process and interpret data obtained from Nimbus-7/Coastal Zone Color Scanner (CZCS) and NOAA Advanced Very High Resolution Radiometer (AVHRR). PC-SEAPAK copyrighted product with all copyright vested in National Aeronautics and Space Administration.

Mcclain, Charles R.