Engineering topics

Mccoy, J. E.

Publications and source records attributed to Mccoy, J. E..

At least 19 records

NASA NTRS1995

Plasma turbulence enhanced current collection: Results from the plasma motor generator electrodynamic tether flight

The plasma motor generator (PMG) experiment, launched June 26, 1993, was a tethered system of two identical plasma contactors connected via a 500-m conducting tether. The experiment was designed to demonstrate the ability of plasma contactors to provide a low-impedance connection between a spacecraft and the ionosphere for both the electron emission and collection. The flight data indicate that plasma contactors enhance electron collection and emission by both neutralizing the electron space charge and scattering electrons across the geomagnetic field lines. Up to a 0.3 A steady current flowed along the tether in a curcuit completed through the ionosphere. An analytical model for plasma contactor interaction with a background plasma which incorporates electron scattering by plasma waves is compared with the flight data. Good agreement between the model and the data is achieved for an effective scattering frequency equal to one twentieth of the local plasma contactor plasma frequency.

Katz, I.↗

NASA NTRS1989

HF sideband generation in the ionosphere

The temporal development of sidebands excited near sunrise by two strong HF waves separated by a few hertz is presented. Sidebands are not observed before sunrise when the ionospheric critical frequency is less than the heater frequency. As the ionospheric density increases following sunrise and overdense conditions are established, strong sidebands emerge. Even though these results favor a mechanism which phase modulates the reflected HF wave over one which first downconverts the HF power to ULF before exciting sidebands, it is possible that either mechanism could at times contribute to sideband production.

Noble, S. T.↗

NASA NTRS1984

Electrodynamic tethers. I - Power generation in LEO. II - Thrust for propulsion & power storage

The power gain and thrust for plasma engines available by unreeling 10 km of insulated Al wire from a spacecraft are investigated. The wire, unreeling in the vertical, would cut the earth's magnetic field lines, thereby generating 20 kW of power in the wire. A drag loss of 20.4 kJ/sec would reduce the power gain to 18.7 kW, an efficiency of 92 percent. Thicker wires could push the power gain to 1 MW at 95 percent efficiency. Conductive 'balloons' at the ends of the tether would function as ionospheric 'brushes' to complete the circuit. Reversing the IXB force by employing on-board stored power would drive the tether current against the induced voltage, providing a 1 N thrust for 8 kW of energy consumed, which could be supplied by solar panels during the day portion of orbit. The equivalent thrust by conventional stationkeeping means would consume 8000 kg of propellant/yr. Techniques for stabilizing the tether in the presence of variable magnetic fields are discussed.

Mccoy, J. E.↗

NASA NTRS1984

Electrodynamic Tethers. 1: Power Generator in LEO. 2: Thrust for Propulsion and Power Storage

An electrodynamic tether consists of a long insulated wire in space whose orbital motion cuts across lines of magnetic flux to produce an induce voltage that in typical low orbits averages about 200 v/km. Such a system should be capable of generating substantial electrical power, at the expense of IXB drag acting on its orbital energy. If a reverse current is driven against the induced voltage, the system should act as a motor producing IXB thrust. A reference system was designed, capable of generating 20 KW of power into an electrical load located anywhere along the wire at the expense of 2.6N (20,000 J/sec) drag on the wire. In an ideal system, the conversion between mechanical and electrical energy would reach 100% efficiency. In the actual system part of the 20 KW is lost to internal resistance of the wire, plasma and ionosphere, while the drag force is increased by residual air drag. The 20 KW PMG system as designed is estimated to provide 18.7 KW net power to the load at total drag loss of 20.4 KJ/sec, or an overall efficiency of 92%. Similar systems using heavier wire appear capable of producing power levels in excess of 1 Megawatt at voltages of 2-4 KV, with conversion efficiency between mechanical and electrical power better than 95%. The hollow cathode based system should be readily reversible from generator to motor operation by driving a reverse current using onboard power.

Mccoy, J. E.↗

NASA NTRS1982

Plasma flow measurements in a simulated low earth orbit plasma

The employment of large, higher power solar arrays for space operation has been considered, taking into account a utilization of high operating voltages. In connection with the consideration of such arrays, attention must be given to the fact that the ambient environment of space contains a tenuous low energy plasma which can interact with the high voltage array causing power 'leakage' and arcing. An investigation has been conducted with the aim to simulate the behavior of such an array in low-earth-orbit (LEO). During the experiments, local concentrations of the 'leakage' current were observed when the panel was at a high voltage. These concentrations could overload or damage a small area of cells in a large string. It was hypothesized that this effect was produced by electrostatic focusing of the particles by the sheath fields. To verify this experimentally, an end-effect Langmuir probe was employed. The obtained results are discussed.

Gabriel, S. B.↗

NASA NTRS1980

Three dimensional space charge model for large high voltage satellites

High power solar arrays for satellite power systems with dimensions of kilometers, and with tens of kilovolts distributed over their surface face many plasma interaction problems that must be properly anticipated. In most cases, the effects cannot be adequately modeled without detailed knowledge of the plasma sheath structure and space charge effects. Two computer programs were developed to provide fully self consistent plasma sheath models in three dimensions as a result of efforts to model the experimental plasma sheath studies at NASA/JSC. Preliminary results indicate that for the conditions considered, the Child-Langmuir diode theory can provide a useful estimate of the plasma sheath thickness. The limitations of this conclusion are discussed. Some of the models presented exhibit the strong ion focusing observed in the JSC experiments.

Cooks, D.↗

NASA NTRS1980

High voltage space plasma interactions

Two primary problems resulted from plasma interactions; one of concern to operations in geosynchronous orbit (GEO), the other in low orbits (LEO). The two problems are not the same. Spacecraft charging has become widely recognized as a problem, particularly for communications satellites operating in GEO. The very thin thermal plasmas at GEO are insufficient to bleed off voltage buildups due to higher energy charged particle radiation collected on outer surfaces. Resulting differential charging/discharging causes electrical transients, spurious command signals and possible direct overload damage. An extensive NASA/Air Force program has been underway for several years to address this problem. At lower altitudes, the denser plasmas of the plasmasphere/ionosphere provide sufficient thermal current to limit such charging to a few volts or less. Unfortunately, these thermal plasma currents which solve the GEO spacecraft charging problem can become large enough to cause just the opposite problem in LEO.

Mccoy, J. E.↗

NASA NTRS1979

A study of the Rima Sirsalis lunar magnetic anomaly

The source of the lunar magnetic anomaly associated with the Rima Sirsalis linear rille has been modelled using the vector field intensities due to arbitrary uniform magnetization in a rectangular prism. It is shown that in order to match the Apollo 16 subsatellite data, the lunar surface near the rille must have a vertical magnetization of 6,000-9,000 G if the anomaly is due to flux leakage from a gap in the crust with the dimensions of the rille. An alternative explanation is that Rima Sirsalis and its surroundings are the site of a vertical magnetization contrast of 100,000-10,000 G which is at least as wide as the rille and extends to a depth of tens of kilometers in the crust. A wider magnetic source reduces the required magnetization (or depth) proportionately, since to first order the field at high altitude is proportional to the magnetic dipole moment per unit length.

Srnka, L. J.↗

NASA NTRS1979

Current leakage for low altitude satellites

Ionospheric plasma densities exceeding 1,000,000 per cu cm exist around satellites in low earth orbit. Operation of large solar arrays at high voltage may drive substantial leakage currents through this surrounding plasma. Power losses exceeding solar cell output have been observed for small arrays biased above +2,000 V. Estimates of these effects for very large power systems are developed. Recent large scale (10 meter) lab tests are reported. Estimates based on calculations of space charge limited sheath dimensions are identified as a good working model, leading to projected power losses for large arrays increasing much more slowly than for small arrays.

Mccoy, J. E.↗

NASA NTRS1979

Current leakage for low altitude satellites - Modeling applications

To simulate the behavior of a high voltage solar cell array in the ionospheric plasma environment, the large (90 ft x 55 ft diameter) vacuum chamber was used to measure the high-voltage plasma interactions of a 3 ft x 30 ft conductive panel. The chamber was filled with Nitrogen and Argon plasma at electron densities of up to 1,000,000 per cu cm. Measurements of current flow to the plasma were made in three configurations: (a) with one end of the panel grounded, (b) with the whole panel floating while a high bias was applied between the ends of the panel, and (c) with the whole panel at high negative voltage with respect to the chamber walls. The results indicate that a simple model with a constant panel conductivity and plasma resistance can adequately describe the voltage distribution along the panel and the plasma current flow. As expected, when a high potential difference is applied to the panel ends more than 95% of the panel floats negative with respect to the plasma.

Konradi, A.↗

NASA NTRS1977

Observations of magnetic merging and the formation of the plasma sheet in the earth's magnetotail

Particle and magnetic field observations of the field line merging process in the earth's magnetotail are presented. By analyzing the lunar shadow pattern of electron fluxes detected by the lunar-orbiting Apollo 16 subsatellite it has been possible to identify the topology and to measure the velocity of the magnetotail field lines. The observations reported here were made as the moon crossed the separatrix between premerging and merged field lines. The measured field line velocities toward the merging region were 30-60 km/s, and the thickness of the separatrix was estimated to be about 2000 km. Most of the magnetic energy released in the merging process appears to go into the energization of particles. The length and the thickness of the merging region are inferred to be of the order of about 10 earth radii and about 4000 km, respectively. The energized particles travel away from the merging region along the separatrix. Those headed earthward may form the plasma sheet by being trapped on closed field lines. The rate of energization and the energy spectrum of those particles are consistent with those required for formation of the plasma sheet.

Lin, R. P.↗

NASA NTRS1977

Linear magnetization feature associated with Rima Sirsalis

Measurements of the magnetic fields by the electron reflection method in the neighborhood of the long structural rille Rima Sirsalis show that a magnetic field with a strength of at least 100 nT (100 gammas) is present over a region of the order of 10 km in width and at least 300 km long. The center of the magnetized region closely parallels and is centered on the rille. The linear magnetization feature extends at least to latitude 8 deg S, 60 km beyond the place where the rille disappears at the edge of Oceanus Procellarum. This extension is coincident with the extrapolation of the rille based on photographs. However, the magnetization is much weaker or entirely absent at 5 deg S and has vanished at 0 deg latitude. These results suggest that the rille is indeed a structural feature and has associated with it magnetization, either in the form of intrusive magnetized rock or of a gap in an otherwise more or less uniformly magnetized layer of rock of large extent in two dimensions. Furthermore, the rille structure evidently is present for some distance beneath the lava flows of the Oceanus Procellarum basin.

Anderson, K. A.↗

NASA NTRS1976

Comparison of simultaneous magnetotail and polar ionospheric electric fields and energetic particles

DC electric fields and solar electrons were simultaneously measured by the Apollo 15 subsatellite in the earth's magnetotail at lunar orbital distance and by rocket and balloon experiments in the polar ionosphere. The magnetotail and polar ionosphere transverse electric fields are found generally to agree in magnitude and direction. The electron spectra from 0.5 to 200 keV are essentially identical, indicating that the potential difference due to parallel electric fields between the magnetotail and the rocket located in the polar ionosphere did not exceed approximately 500 V during the time of the measurements.

Mccoy, J. E.↗

NASA NTRS1976

Photometric studies of light scattering above the lunar terminator from Apollo solar corona photography

Excess brightness is found in 70-mm photographs of the solar corona above the lunar terminator during Apollo 15 and 17. Maximum brightness of this scattered light is determined from calibration of image density. The observed excess brightness displays circular symmetry above the lunar-horizon subsolar point, characteristic of forward diffraction scattering from micron or submicron size (solid) grains, and decays rapidly in intensity with altitude and distance from the lunar terminator. The observed brightness cannot be accounted for by a co-orbiting cloud of spacecraft contaminants, but requires a variable lunar dust 'atmosphere' over the terminator regions extending to altitudes in excess of 100 km. To maintain such large masses of lunar fines above the terminator requires either local mass-churning rates in excess of 2 by 10 to the -11th power g/sq cm sec or the assumption of some degree of high-altitude electrostatic suspension to increase the dwell time of individual grains at the altitudes observed. Such a model would reduce mass-churning rates while causing selective erosion/deposition and potential for escape of significant mass from the moon

Mccoy, J. E.↗

NASA NTRS1976

Lunar surface remanent magnetic fields detected by the electron reflection method

We present maps of the lunar surface remanent magnetic fields detected by the electron reflection method. These maps provide substantial coverage of the latitude band from 30 N southward to 30 S with a resolution of about 40 km and a sensitivity of about 0.2 gamma at the lunar surface. Regions of remanent magnetization are observed ranging in size from the resolution limit of 1.25 deg to above approximately 60 deg. The largest contiguous region fills the Big Backside Basin where it is intersected by the spacecraft orbital tracks. Preliminary analyses of the maps show that the source regions of lunar limb compressions correspond to regions of strong surface magnetism, and that there does not appear to be sharply discontinuous magnetization at the edges of maria. We also analyze the electron reflection observations to obtain information on the direction and distribution of magnetization in the Van de Graaff anomaly region.

Lin, R. P.↗

NASA NTRS1975

Measurement of lunar and planetary magnetic fields by reflection of low energy electrons

The paper describes the technique of planetary electron reflection magnetometry (PERM), a method for measuring the magnitude, direction, and scale size of magnetic fields near the surface of the moon and other planetary bodies with weak and small-scale-size surface fields. It is noted that the PERM technique is based on the ability of magnetic fields to reflect charged particles. A qualitative account of the implementation of the technique is presented along with some results obtained by the Apollo 15 and 16 Particles and Fields subsatellites. The quantitative aspects of PERM are treated by examining solutions to the equation of motion of a charged particle in a magnetic field, computing reflection coefficients on the basis of trajectory calculations, and determining the direction of the lunar surface magnetic field. The sensitivity of the PERM technique is calculated, and effects of lunar electric fields and spacecraft potentials on the measurements are described. Extension of the technique to Mars and Venus is discussed.

Anderson, K. A.↗

NASA NTRS1975

Lunar remnant magnetic field mapping from orbital observations of mirrored electrons

A technique is described for mapping areas of lunar surface magnetism by observing ambient low-energy electrons from lunar orbit with a detector that is sectored to distinguish directions of arrival with respect to the ambient magnetic field and the lunar surface. It is noted that the ambient electrons provide a probe along the ambient magnetic-field lines down to the lunar surface for remote sensing of the presence of surface fields. Unlike direct magnetometer measurements, this probe does not require low altitude or a very stable ambient field in order to map the occurrence regions of such fields. Preliminary maps generated for the surface magnetic areas underlying the orbit of the Particles and Fields Satellite deployed from Apollo 16 are presented to demonstrate the feasibility of this technique.

Mccoy, J. E.↗

NASA NTRS1975

Magnetotail electric fields observed from lunar orbit

Direct observations of convection electric fields in the earth's magnetotail are reported. The electric fields have been measured from lunar orbit by detection of the E x B/B-squared drift displacement of low-energy electrons at the limb of the moon. It is found that electric fields range in magnitude from a value less than or equal to 0.02 mV/m, the limit of sensitivity of the method, to 2 mV/M. The typical value is 0.15 mV/M, and the corresponding convection velocity is 15 km/s. The sense of the electric field is almost always dawn to dusk. The electric field is often variable on a time scale of hours and sometimes minutes. The observations indicate that the electric field is not uniform across the magnetotail. If it is assumed that the typical measured electric-field value represents an average over the inhomogeneities, the potential drop across the entire tail is of the order of 40 kV.

Mccoy, J. E.↗