Engineering topics

Mcginness, H. D.

Publications and source records attributed to Mcginness, H. D..

7 records

NASA NTRS1985

A Description of the 64-meter Antenna Elevation Drive Gears and Their Strange Wear

The Deep Space Station (DSS) 64-m antenna elevation axis drive is executed by torquing two bull gears, concentric to the elevation axis, with the output pinions of four gear boxes. These gear boxes have functioned well during the 18 and 11 years, respectively, that the DSS 14, and the DSS 43 and DSS 63 antennas have been in service. A strange wear pattern gradually developed on the bull gears and driving pinions of all three antennas. These patterns were well developed after 8 years and apparently are intensifying in all instances. The elevation drive gears are described and their wear is compared to the wear of other antenna drive gears. The comparison is perplexing and satisfying explanations have not yet been made.

Mcginness, H. D.↗

NASA NTRS1985

Antenna Axis Drive Torques for the 70-meter Antenna

Antenna axis speeds versus wind speeds are given in terms of dish size, hydraulic motor size, and the number of servo valves. An increase in the dish diameter of antenna is usually accompanied by increases in the axis torques required to drive the antenna against wind. The proposed increase in the diameters of the 64-m antenna dishes to 70 m (plus a noise shield) does require increased axis torques. The increased dish diameter causes the maximum azimuth and elevation torques to increase 48% and 43% respectively.

Mcginness, H. D.↗

NASA NTRS1985

An Evaluation of the 64-meter Antenna Radial Bearing for Use on the 70-meter Antenna

The derivation of the proper truck preload is discussed and is shown to be dependent upon the azimuth drive preload direction, the wind direction and magnitude, and the out of roundness of the track. The resulting wheel and track contact stresses were evaluated and found to be satisfactory for either the 64-m or 70-m antenna. The wheel bearing loads were found to be quite satisfactory for the larger 70-m antenna. Methods for evaluating the effects of track out of roundness and for aligning the wheel and truck assemblies are presented. It is believed that these methods are practical and that the increased loadings on the parts should not affect the expected long life of the azimuth bearing.

Mcginness, H. D.↗

NASA NTRS1985

Elevation Bearing Maximum Load, 70-meter Antenna

One of the preliminary frequency analyses of the 64-m antenna disclosed that considerable flexibility was attributable to the structure adjacent to the elevation bearings. In order to reduce this compliance, this adjacent structure and the bearings were made substantially larger. The result is that the stresses in these parts are small when used with the 64-m reflector and should remain sufficiently small when used with the larger 70-m reflector, which has an extended one-meter noise shield at its outer edge. The loads on the elevation bearings of the larger 70-m reflector are documented and these loads are compared to the corresponding ones of the 64-m antenna.

Mcginness, H. D.↗

NASA NTRS1985

Characteristics of the Elevation Drive Suspension of the 64-meter Antennas

The elevation axis drive unit of the DSN 64-m antennas is arranged so that its output pinion can self-align to the bull gear. The design is described and conflicting desiderata are discussed. Static stability criterion for the elevation drive, derivation of strut stiffness ratios, and an outline for removing, installing, and adjusting the vertical struts are included.

Mcginness, H. D.↗

NASA NTRS1985

Hydrostatic Bearing Pad Maximum Load and Overturning Conditions for the 70-meter Antenna

The reflector diameters of the 64-m antennas were increased to 70-m. In order to evaluate the minimum film thickness of the hydrostatic bearing which supports the antenna weight, it is first necessary to have a good estimation of the maximum operational load on the most heavily loaded bearing pad. The maximum hydrostatic bearing load is shown to be sufficiently small and the ratios of stabilizing to over turning moments are ample.

Mcginness, H. D.↗

NASA NTRS1981

Suspension system for a wheel rolling on a flat track

An improved suspension system for an uncrowned wheel rolling on a flat track is presented. It is characterized by a wheel frame assembly including a wheel frame and at least one uncrowned wheel connected in supporting relation with the frame. It is adapted to be seated in rolling engagement with a flat track, a load supporting bed, and a plurality of flexural struts interconnecting the bed in supported relation with the frame. Each of said struts is disposed in a plane passing through the center of the uncrowned wheel surface along a line substantially bisecting the line of contact established between the wheel surface and the flat surface of the truck and characterized by a modulus of elasticity sufficient for maintaining the axis of rotation for the wheel in substantial parallelism with the line of contact established between the surfaces of the wheel and track.

Mcginness, H. D.↗