Search NASA⌕ Search

Engineering topics

Mcintosh, S. C., Jr.

Publications and source records attributed to Mcintosh, S. C., Jr..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Static aeroelastic analysis and tailoring of missile control fins

A concept for enhancing the design of control fins for supersonic tactical missiles is described. The concept makes use of aeroelastic tailoring to create fin designs (for given planforms) that limit the variations in hinge moments that can occur during maneuvers involving high load factors and high angles of attack. It combines supersonic nonlinear aerodynamic load calculations with finite-element structural modeling, static and dynamic structural analysis, and optimization. The problem definition is illustrated. The fin is at least partly made up of a composite material. The layup is fixed, and the orientations of the material principal axes are allowed to vary; these are the design variables. The objective is the magnitude of the difference between the chordwise location of the center of pressure and its desired location, calculated for a given flight condition. Three types of constraints can be imposed: upper bounds on static displacements for a given set of load conditions, lower bounds on specified natural frequencies, and upper bounds on the critical flutter damping parameter at a given set of flight speeds and altitudes. The idea is to seek designs that reduce variations in hinge moments that would otherwise occur. The block diagram describes the operation of the computer program that accomplishes these tasks. There is an option for a single analysis in addition to the optimization.

Mcintosh, S. C., Jr.↗
NASA NTRS1984

Optimal redesign study of the harm wing

The purpose of this project was to investigate the use of optimization techniques to improve the flutter margins of the HARM AGM-88A wing. The missile has four cruciform wings, located near mid-fuselage, that are actuated in pairs symmetrically and antisymmetrically to provide pitch, yaw, and roll control. The wings have a solid stainless steel forward section and a stainless steel crushed-honeycomb aft section. The wing restraint stiffness is dependent upon wing pitch amplitude and varies from a low value near neutral pitch attitude to a much higher value at off-neutral pitch attitudes, where aerodynamic loads lock out any free play in the control system. The most critical condition for flutter is the low-stiffness condition in which the wings are moved symmetrically. Although a tendency toward limit-cycle flutter is controlled in the current design by controller logic, wing redesign to improve this situation is attractive because it can be accomplished as a retrofit. In view of the exploratory nature of the study, it was decided to apply the optimization to a wing-only model, validated by comparison with results obtained by Texas Instruments (TI). Any wing designs that looked promising were to be evaluated at TI with more complicated models, including body modes. The optimization work was performed by McIntosh Structural Dynamics, Inc. (MSD) under a contract from TI.

Mcintosh, S. C., Jr.↗
NASA NTRS1978

On the optimization of discrete structures with aeroelastic constraints

The paper deals with the problem of dynamic structural optimization where constraints relating to flutter of a wing (or other dynamic aeroelastic performance) are imposed along with conditions of a more conventional nature such as those relating to stress under load, deflection, minimum dimensions of structural elements, etc. The discussion is limited to a flutter problem for a linear system with a finite number of degrees of freedom and a single constraint involving aeroelastic stability, and the structure motion is assumed to be a simple harmonic time function. Three search schemes are applied to the minimum-weight redesign of a particular wing: the first scheme relies on the method of feasible directions, while the other two are derived from necessary conditions for a local optimum so that they can be referred to as optimality-criteria schemes. The results suggest that a heuristic redesign algorithm involving an optimality criterion may be best suited for treating multiple constraints with large numbers of design variables.

Mcintosh, S. C., Jr.↗
NASA NTRS1975

Weight minimization of structures for fixed flutter speed via an optimality criterion

A rigorous optimality criterion is derived and a hybrid weight-reduction algorithm developed for the weight minimization of lifting surfaces with a constraint on flutter speed. The weight-reduction algorithm incorporates a simple recursion formula derived from the optimality criterion. Monotonic weight reduction is accomplished by dynamically adjusting a parameter in the recursion formula so as to achieve a predetermined weight decrease. The algorithm thus combines the simplicity of optimality-criterion methods with the convergence characteristics of mathematical-programming methods. The imposition of the flutter constraint is simplified by forcing to zero the imaginary part of the flutter eigenvalue, with the airspeed fixed. Four examples are discussed. The results suggest that significant improvements in efficiency are possible, in comparison with techniques based purely on mathematical programming.

Segenreich, S. A.↗
NASA NTRS1974

Theoretical considerations of some nonlinear aspects of hypersonic panel flutter

A research project to analyze the effects of hypersonic nonlinear aerodynamic loading on panel flutter is reported. The test equipment and procedures for conducting the tests are explained. The effects of aerodynamic linearities on stability were evaluated by determining constant-initial-energy amplitude-sensitive stability boundaries and comparing them with the corresponding linear stability boundaries. An attempt to develop an alternative method of analysis for systems where amplitude-sensitive instability is possible is presented.

Mcintosh, S. C., Jr.↗
NASA NTRS1973

Control law synthesis and sensor design for active flutter suppression.

Methods are presented for representing unsteady aerodynamic loadings, valid for arbitrary motion, for the two-dimensional typical section with a trailing-edge control surface in incompressible flow and a three-dimensional lifting surface with leading- or trailing-edge control surfaces in subsonic compressible flow. Loads for the two-dimensional incompressible case are obtained via analytic continuation of the Theodorsen function into the complex plane, with guidance from a time-domain approximation of the Wagner indicial function. For the three-dimensional case, it is proposed that oscillatory generalized aerodynamic forces be approximated by Pade fractions, thereby permitting an obvious continuation into the complex plane. A theoretical justification for this procedure is briefly outlined, and some practical aspects of its implementation are discussed.

Lyons, M. G.↗
NASA NTRS1972

The effect of hypersonic nonlinear aerodynamic loading on panel flutter.

The system considered is a two-dimensional isotropic panel, or plate-column, on hinged supports, with one end spring restrained in the plane of the panel. Panel geometric nonlinearities and piston-theory aerodynamic nonlinearities are included. Results from an earlier preliminary study indicate that only two second-order nonlinear aerodynamic terms are important. The nonlinear aerodynamic terms introduce the possibility of an amplitude-sensitive instability, where the panel is unstable to disturbances of a certain magnitude but stable for smaller ones. This type of instability is examined for various panel in-plane loads and initial conditions, with other parameters having values representative of current practice. A single new interaction parameter, representing the importance of the nonlinear aerodynamic terms in comparison with the panel geometric nonlinear terms, is introduced. A parameter survey is presented, involving this parameter and the static pressure difference across the panel. Finally, the practical impact of this type of instability is discussed.

Mcintosh, S. C., Jr.↗